Table of Contents COPYRIGHT ................................2 FCC INTERFERENCE STATEMENT ........................2 CHAPTER 1 PRODUCT INFORMATION ......................1 1.1 I ....................1 NTRODUCTION AND SAFETY INFORMATION 1.2 P ..........................2 ACKAGE ONTENTS 1.3 F .................... 3 AMILIAR WITH YOUR NEW REEN OUTER CHAPTER 2 CONFIGURE THE ROUTER ......................
Page 4
3.6 A ..........................46 CCESS ONTROL 3.6.1 IP Filtering ..........................47 3.6.2 MAC Filtering ..........................50 3.6.3 Domain Filtering ........................52 3.7 D DNS ............................ 54 YNAMIC 3.8 S ........................... 56 YSTEM OOLS 3.8.1 Firmware Upgrade ........................56 3.8.2 Backup & Restore ........................57 3.8.3 Diagnostic Tools ........................
WPA2-PSK provide the highest level of wireless network security. The bundled EZ Setup Wizard allows you to set up the router with an easy-to-use user interface. Best of all, AR686WV2 works with all 802.11n / g / b network devices which ensures compatibility with the existing wireless products.
1.2 Package Contents Before you start using this router, please check if there is anything missing in the package, and contact your dealer of purchase to claim for missing items: 1. Wireless N 300 Green Router with 2 un-detachable Antennas 2.
1.3 Familiar with your new Green Router A. Front Panel LEDs Status Description Power On Power Power Off Blinking WPS Active Easy-Setup Button WPS Inactive Blinking System Function Normal System Steady On / Off System Loading / Malfunction Flashing Wireless Data Transmitting Wireless LAN Wireless Inactive WAN Active...
Page 8
B. Back Panel Button Description Easy-Setup Press and hold until the WPS™ light begins to blink. This Button will initiate WPS™ search on your router in order to (WPS™ quickly create a secure network connection with other compatible) WPS™-compatible devices. Press this button and hold for 7 seconds to restore Reset factory default settings.
Chapter 2 Configure the Router 2.1 Connect the Router to your network Note: Prior to connecting the router, be sure to power off your computer, DSL/Cable modem, and the router. Step 1 Connect one end of a network cable to the WAN port of the router and connect the other end of the cable to the DSL/Cable modem.
Page 10
Step 4 Plug the power adapter to the router and connect it to an electrical outlet. Step 5 Power on your computer. Step 6 Check LEDs of the router: make sure Status, WAN, W.LAN, and the LAN port that the computer is connected to are ON.
2.2 Configure the Router with Quick Setup Setting up the router is made easy with the Quick Setup page. Here you can configure the most basic aspects of your router. Step 1 Open the web browser (i.e. Internet Explorer or Mozilla Firefox) of the computer connected to the router and type 192.168.2.1 or the IP address you assigned to this router in the address bar and press Enter.
2.2.1 Internet Connection Type Select the WAN type associated with your ISP. For Cable Users: Please select DHCP (Dynamic Host Configuration Protocol). If your ISP has assigned you a Static IP: Please select Static IP and enter the IP information provided by your ISP. Press Save to apply changes.
2.2.2 Wireless Setup Here you can instantly set up your Wireless Network. SSID (Network Name): Choose a name for your wireless network. Make sure to use a name that you can easily remember. The default SSID is set to Airlink101. Press Save to after you have chosen your own unique network name.
2.3 Connect to Router Wirelessly In this section, you can find the instructions of how to connect to the router wirelessly with your Windows 7 computer. You can also refer to the manual of your wireless adapter on how to connect to the router. Step 1 Click on the wireless icon in the system tray on your desktop.
Chapter 3 Advanced Router Configuration You can make advanced configurations on this router to meet your network’s needs, such as: Virtual Server, Access Control, Network Security, etc. If you have already gone through the Setup Wizard, you do NOT need to configure anything here for you to start using the Internet.
3.1 Status The status page shows the current router configurations. You can find detailed information about your wired and wireless network here as well as the WAN connection. 3.2 Network Here you can configure the Networking properties of the router.
3.2.1 WAN 3.2.1.1 WAN Type – Wired Access Select Wired Access if you are connecting to your Modem using an Ethernet cable. Under WAN Settings select the WAN Connection Type used by your ISP. A. Dynamic IP Address: Click on Dynamic IP if you are connecting to Internet through a cable modem.
Page 18
Please see the following instructions for settings for the 3 most common WAN types: A) DHCP DHCP WAN is the common among cable ISP’s. There is no configuration necessary. Click on Advanced if you’d like to manually set the DHCP Parameter Description MAC Address...
Page 19
B) Static IP Address Enter the WAN IP address, WAN Subnet Mask, WAN Gateway, Primary DNS , and Secondary DNS addresses provided by your ISP. After you’ve finished all settings, click Save to save the setting. The change will take effect after the router automatically reboots.
Page 20
Parameter Description Username Enter the User Name for your DSL account, you can obtain this information from your ISP. Password Enter the Password for your DSL account, you can obtain this information from your ISP. MAC Address Please input MAC address of your computer here if your ISP only permits computer with certain MAC address to access Internet.
Page 21
MTU (Maximum Transmission Unit) The most common MTU value is 1480. You can configure it as your ISP suggested. Server Name Enter the DSL service company. This is optional. PPPoE AC Name Enter name of the Access Concentrator you’d like to connect to. Leave it blank for automatic configuration.
Page 22
Step 2 Press AP Scan to view a list of available networks. Alternatively, you may manually enter the SSID of the network you’d like to connect to. Step 2 Select the network you’d like to connect to by marking the circle on the right of the network.
Step 4 Select the WAN Connection Type of the network you are connecting to. Enter the configurations for the connection type associated with the network you are connecting to. Please see Section 3.2.1.1 for information on how to configure the individual connection types.
Page 24
Enter the LAN configurations in order to adjust the settings of your Local Area Network. Parameter Description IP Address The local IP address of this router. You can change it if necessary. Subnet Mask Enter the Password for your DSL account, you can obtain this information from your ISP.
3.2.3 IPTV If your television service uses IPTV, you can configure the settings here. Please consult your TV service providers for more details on how to configure the IPTV settings. 3.2.4 Address Reservation When using a DHCP server you may find situations where you want to reserve an IP address for a certain network device.
Page 26
Step 2 Enter the IP Address you would like to reserve. Make sure the IP address is configured statically to the Network Device you are using. Step 3 Enter the MAC Address of the network device. Step 4 Click Add to finish reserving the IP Address. The client will now appear in the Address Reservation List.
Bridge Mode: Turn the AR686WV2 into a bridge by selecting Bridge Mode and pressing Save. NOTE: If would like to return the AR686WV2 from Bridge Mode to Router Mode, you will need to perform a factory reset by holding the reset button for 10 seconds with the power attached.
3.3.1.1 for more information on the different Radio Modes. 3.3.1.1 Radio Modes The wireless radio on the AR686WV2 is capable of different functions. Select the mode based on the function you need. A. Access Point This is the standard wireless mode. Wireless devices will be able to connect to the...
Page 29
Parameters Description Wireless Mode Please select the wireless mode from one of the following options: 11b/g/n mixed: 2.4GHz band, allows 802.11b, 802.11g, and 802.11n wireless network clients to connect to this router (maximum transfer rate 11Mbps for 802.11b clients, maximum 54Mbps for 802.11g clients, and maximum 300Mbps for 802.11n clients*).
Page 30
SSID Broadcast Select Enable to broadcast the SSID so that your wireless client can detect it on the available wireless network list. Region Select the region you live in. Channel Please select a channel from the drop-down list of ‘Channel Number’ for broadcasting. You can let the router automatically choose a channel or manually assign one yourself.
Page 31
Key Mode: Select HEX or ASCII. You can select ASCII (alphanumeric format) or Hexadecimal (in the “a~f” and “0~9” range) for the key format. Password: Set a WEP Key you wish to use and enter the key value. If you select HEX and 64 bits, enter a 10-digit Hex key, for example, “12345abcde”.
Page 32
Password: Enter 8~63 characters as the security key of your wireless network. B. Repeater Repeater mode takes the wireless signal from another router and broadcasts it as its own. You can extend the range of your existing router by using Repeater mode. Step 1 Scan for existing wireless networks by pressing AP Scan.
Page 33
Step 3 Enter the password of the network you are trying to replicate. Step 4 Press Save and wait for 2-5 minutes to allow the AR686WV2 to pick up the signal from the router whose network you are repeating. C. AP+WDS This function is very similar to Repeater mode in that the router will take its input signal from a pre-existing network.
Page 34
Step 1 Select AP+WDS as the Radio Mode. Step 2 Set the SSID for the network. This will be the name of your network, so make sure it is easy to remember and recognizable. As usual, the default will be Airlink101.
Page 35
Press AP Scan to bring up a list of available networks. Step 4 Just like in Repeater mode and W-ISP, the AR686WV2 will source its Internet connection from this base network. Select the network you’d like to use and press Connect to continue.
Page 36
Step 6 Setup the security settings for your new network. Please see AP Security Settings in the Access Point section for more details. The factory default is ‘password’. We recommend changing that to something that only you will know. Step 7 Press Save to apply the changes and initiate the AP+WDS function.
Setup is very similar to Repeater and WDS mode with the difference being that the AR686WV2 will NOT repeat the wireless signal from the existing network. This is similar to Bridge mode, with the difference being that Client mode will only output signal to a single device on the LAN.
Page 38
Step 1 Enable or Disable the MAC Filter. Step 2 Choose whether or not the clients on the list are denied or granted exclusive access to the wireless network. Step 3 Press Save to continue. Step 4 Enter a quick description of the device you want to filter. Step 5 Enter the MAC address of the device you want to filter.
Step 6 Press Add to create the client profile. Your full clientelle will be listed below on the Wireless MAC Filtering List. 3.3.3 WPS Setting WPS is a way to connect a wireless device to the network with the press of a button or by entering a PIN.
Page 40
Easy Push Button After WPS has been enabled, press the WPS button on the router for 2 seconds and then press the WPS button on your device in order to establish a wireless connection. See your devices User Manual for specific push-button protocol. PIN Code Use the PIN code generated by the router to connect with your device.
3.3.4 Multiple SSID The AR686WV2 is able to broadcast up to 3 additional wireless networks. Step 1 Choose which SSID you’d like to configure Step 2 Press Enable to activate the AP selected in the previous step. Step 3 Set the SSID for the new network. Make sure to name the network differently...
Page 42
Step 4 Enable or Disable the SSID Broadcast to control whether or not the network is detectable by other network devices. Step 5 Set the Access Control of the new network. Step 6 Choose the Authentication Type. Please see section 3.3.1.1 part A for further instructions on securing the network.
3.4 Bandwidth Control Bandwidth Control allows you to control the amount of data used by the network. This is especially useful if you have Bandwidth limitations set by your ISP or if a particular network device is taking up too much of your available bandwidth. Step 1 Enable Bandwidth control to activate the function.
Page 44
Step 4 Set a Description for the device or devices associated with the Bandwidth rule you are setting. Step 5 Enable or Disable the control rule you are setting. Step 6 Choose the devices that the rule will apply to. You can select all the devices on the network, or use set a rule for a specific device using the IP address or subnet.
Page 45
Step 8 Set Restricted Bandwidth Limitation if you want to limit the bandwidth allotted to device(s) in the rule. This will restrict how much data the device(s) in the rule can use. Step 9 Press Add to activate the rule. To view or modify the active rules, look at the Bandwidth Control List.
3.5 Forwarding This section covers all the Forwarding functions of your router. 3.5.1 Virtual Server The Virtual Server allows external devices to communicate with devices inside your network over the internet. Set the server rules to control which devices are granted remote access.
Page 47
Step 4 Set the External Port number or range. This will be the port number needed to access the device from the outside. Step 5 Set the Internal Port number or range. In most cases the Internal and External ports will be the same. Step 6 Press Add to add the new rule to the Virtual Server.
3.5.2 DMZ The DMZ (Demilitarized Zone) function allows unregulated communication for a specific device on the network. We don’t recommend using DMZ unless the device you are using will not work behind a Firewall. There are two different types of DMZ connections: 1.
Page 49
Step 3 Press Save to apply the change. 2. Super DMZ – Super DMZ assigns the WAN IP address to the device. This may affect other clients on your LAN. Step 1 Select Enable to activate the Super DMZ function. Step 2 Enter the MAC Address of the network device that will be set to the Super DMZ.
3.5.3 UPnP UPnP (Universal Plug and Play) is automatically enabled. Here you can enable or disable UPnP function. 3.5.4 Port Triggering Port Triggering is very similar to Port Forwarding and is used for special applications. Please see section 3.5.1 for more information on how to configure Port Triggering Rules. 3.6 Access Control You can control how or when clients in the network communicate with each other and with the internet.
3.6.1 IP Filtering IP Filtering allows you to control who can connect to your wireless network. This is similar to the MAC filtering covered in Section 3.3.2, but the devices are identified by their IP addresses and you can schedule specific times for the rules you set. Step 1 Enable or Disable the IP Filter.
Page 52
Step 4 Enter a quick description of the device you want to filter. Step 5 Set the whether or not the new Rule allows or denies access. Step 6 Enter the IP information of the device you want to filter.
Page 53
Step 7 Set the Day(s) and Time(s) you’d like the rule to be active. Step 8 Press Add to create the client profile. Your full clientelle will be listed below on the IP Filtering List.
3.6.2 MAC Filtering MAC Filtering allows you to control who can connect to your wireless network. This is similar to the MAC filtering covered in Section 3.3.2 with the addition of scheduling options. Step 1 Enable or Disable the MAC Filter. Step 2 Choose whether or not the clients on the list are denied or granted exclusive access to the wireless network.
Page 55
Step 5 Set the whether or not the new Rule allows or denies access. Step 6 Enter the MAC address of the device you want to filter. Step 7 Set the Day(s) and Time(s) you’d like the rule to be active. Step 8 Press Add to create the client profile.
3.6.3 Domain Filtering Domain Filtering allows you to control which websites clients can or cannot access based on key words. Step 1 Enable or Disable the function. Step 2 Choose whether or not the domains will be denied or granted access. Step 3 Press Save to apply the changes.
Page 57
Step 5 Choose whether the rule will Permit or Deny access to websites in the rule. Step 6 Enter the Keywords for the domains you’d like to filter. Any website name containing the Keywords will be affected by the filter. Step 7 Set the Day(s) and Time(s) you’d like the rule to be active Step 8...
Your Domain rules will be listed below on the Domain Filtering List. 3.7 Dynamic DNS You may set up DDNS access to the router in order to reach the router from outside the network. Step 1 Choose to Enable or Disable the DDNS feature. Step 2 Select the DDNS Service Provider that you use.
Page 59
Step 3 Enter the Username and Password associated with your DDNS account. Step 4 Enter the Domain Name(web address) registered to your DDNS account. Step 5 Press Save to apply the changes and check your connection in the Connection Status box.
3.8 System Tools Use the System Tools for general Router maintenance and configuration. 3.8.1 Firmware Upgrade Firmware Upgrades can be done within the System Tools. It is recommended to connect directly to the router through one of the LAN ports when performing a Firmware Upgrade. Step 1 Select Browse to select the new firmware file.
3.8.2 Backup & Restore You may save your configurations here or load a previously saved router configuration. Step 1 Select Backup in order to save your current router configuration. Step 2 Use the Browse button to search for saved configurations. Step 3 Press Restore in order to load the configuration that you have chosen.
3.8.3 Diagnostic Tools Diagnostic Tools allow you to perform simple troubleshooting to see if the router is connected to the internet. Step 1 Select which type of diagnostic test you’d like to perform. Step 2 Enter the IP Address or website that you would like to test. Step 3 Click on Start to begin the diagnostic test.
3.8.4 Remote Management Remote Management allows you to access your router via the internet. This is useful to check on your network when away from home or to allow someone else in to help you configure your router. For security reasons, this feature is disabled by default and we do not recommend leaving this feature on unless you have set a new username and password on the router.
3.8.5 Time Management Adjust the internal clock of your Router. This is a very important step if you have enabled any rules that run on a schedule. Select the NTP (Network Time Protocol) of your time zone or manually enter the time yourself. If you have your own NTP server, you may also use that to set your router’s clock.
Page 65
Step 2 Type the password that you would like to use. Please note that the password is case-sensitive. Step 3 Confirm your new password by retyping the password in the box. Step 4 Save your changes.
3.8.7 Statistics View router activity and performance here. Press Refresh in order to update the page. Parameter Description System Uptime Displays the amount of time the router has been running. CPU Usage Displays the current use of the processor (CPU). Memory Usage Displays the current use of the memory (RAM).
3.8.8 System Log View past events on the System Log. The Log is active as long as the router is running. You may scroll pages to see older events or delete the history by selecting Delete All. 3.8.9 System Restart Restart the entire router here.
Technical Support E-mail: support@airlink101.com Toll Free: 1-888-746-3238 Website: www.airlink101.com *Theoretical maximum wireless signal rate derived from IEEE standard 802.11 specifications. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, mix of wireless products used, radio frequency interference (e.g., cordless telephones and microwaves) as well as network overhead lower actual data throughput rate.
Need help?
Do you have a question about the AR686WV2 and is the answer not in the manual?
Questions and answers