Advertisement
Quick Links
Advertisement
Related Manuals for Hunter Tea Stain Bowl Light Kit
Summary of Contents for Hunter Tea Stain Bowl Light Kit
- Page 1 Tea Stain Bowl Light Kit Installation Instructions 43536-01 r111407...
- Page 2 • To avoid possible electrical shock, before installing light fixture disconnect power by turning off the circuit breakers both to the outlet box and to its associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel. • Connect house wiring to the fan before attaching the light fixture to the fan. • All wiring must be in accordance with national and local electrical codes. If you are unfamiliar with wiring, you should use a qualified electrician. Professional installation is recommended. • To reduce the risk of fire or personal injury, allow bulbs and surrounding surfaces to cool to room temperature before touching or removing them. This light fixture is for use only on Hunter Ceiling Fans Type A-Z. This light fixture weighs 3.66 pounds. This manual contains installation instructions for the following types of fans: • Fans With Removable Switch Housing • Fans With Non-Removable Switch Housing • Fans With Non-Removable Switch Housing and No Center Hole Preparing the Installation Site 1. Disconnect power by turning off the circuit breakers both to the outlet box and to its associated wall switch...
- Page 3 Installing the Light Kit on Fans With Removable Switch Housing 1. Unscrew the three screws from the upper switch housing. Disconnect the 9-pin plug connectors. Remove the lower switch housing. 2. Push the plug from inside the lower switch housing to remove the plug and switch housing cap. NOTE: Save the plug button and switch housing cap should you choose to remove the light fixture in the future. Removable Switch Housing CAUTION: If your fan is operated by remote control, take care not to damage the small components on the circuit board inside the housing. 3. Screw the threaded rod of the upper light housing into the center of the lower switch housing until you feel resistance. Unscrew the upper light housing slightly 9-Pin Plug until the holes of the upper light housing are aligned with the holes in the lower Connector switch housing. 4. Finish attaching the upper light housing to the lower switch housing using the two attachment screws included. Securely tighten the two screws. 5. Install the nut and washer inside the upper switch housing onto the threaded Screw rod from the upper light housing.
- Page 4 8. Remove the wire connectors from the two wires in the switch housing labeled “Connect Light Here” or “For Light Use.” To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist the wire connector clockwise until tight. Connect the black/white striped wire from the switch housing to the black wire from the light kit. Connect the white wire from the switch housing to the white wire from the light kit. Secure all wire connections using wire connectors. Wires and Wire CAUTION: Be sure no bare metal wires or wire strands are visible after making connectors the connections. 9. Reconnect the 9-pin plug connector. Steps 8-10 10. Install screws to reattach the lower switch housing to the upper switch housing. 11. Go to the instructions for Installing the Bulbs, Chains, and Globe. 43536-01 r111407 4...
- Page 5 Installing the Light Kit on Fans With Non-Removable Switch Housing 1. Uninstall the two screws from the switch housing cover. 2. Remove the plug or screw from the center of the switch housing cover. 3. Thread the switch housing cover onto the upper light housing. Align the screw holes in the upper light housing with the screw holes in the switch housing cover. Install the nut and washer onto the threaded rod from the light kit to secure the Non-Removable Switch Housing switch housing cover. with Center Hole WARNING: Improper installation could cause the light fixture to fall, or result in electrical shock or personal injury. 4. Remove the wire connectors from the two wires in the switch housing labeled “Connect Light Here” or “For Light Use.” One wire is white and the other wire is black/white striped. 5. Feed the two wires from the switch housing through the threaded rod in the upper light housing. Switch Housing 6. Align the threaded screw holes in the switch housing cover with the threaded Cover holes in the switch housing. Attach the switch housing cover and upper light housing assembly to the switch housing using the included attachment screws. 7. To connect the wires, hold the bare metal leads together and place a wire Steps 1–2 Attachment connector over them, then twist the wire connector clockwise until tight. Screw Plug Connect the black/white striped wire from the switch housing to the black wire from the light kit. Connect the white wire from the switch housing to the Switch...
- Page 6 Installing the Light Kit on Fans With Non-Removable Switch Housing and No Center Hole 1. Uninstall the two screws from the switch housing plate. 2. Remove the wire connectors from the two wires in the switch housing labeled “Connect Light Here” or “For Light Use.” One wire is white and the other wire is black/white striped. Thread the two wires through the hole in the center of the upper light housing. 3. Align the screw holes in the upper light housing with the screw holes in the Hunter original and non- switch housing. Install the upper light housing to the switch housing using the removable switch, no center hole two attachment screws provided. 4. To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist the wire connector clockwise until tight. Connect the black/white striped wire from the switch housing to the black wire from the light kit. Connect the white wire from the switch housing to the white wire from the light kit. Secure all wire connections using wire connectors. CAUTION: Be sure no bare metal wires or wire strands are visible after making the connections. 5. Attach the light kit to the upper light housing by partially installing two screws Screw in the upper light housing. Align the keyhole slots in the light kit with the Switch Step 1 Housing preinstalled screws. Turn the light kit clockwise until the housing assembly Plate screws are firmly situated in the narrow end of the keyhole slots. Install a third screw into the upper light housing. Tighten all three screws firmly. WARNING: Improper installation could cause the light fixture to fall, or result in electrical shock or personal injury. 6. Go to the instructions for Installing the Bulbs, Chains, and Globe.
-
Page 7: Troubleshooting
Fan Pull 4. Place the cover plate up against the glass bowl. Align the holes in the Light Pull Chain Chain cover plate with the grommet hole of the metal disc. 5. Screw the finial onto the threaded rod end until tight . 6. The installation is complete and you can restore power to the ceiling fan. Hole (Cover Plate) Finial Steps 1–5 Hunter Fan Company 2500 Frisco Avenue Memphis, Tennessee 38114 Troubleshooting For other problems or questions, contact the Light does not come on. Hunter Fan Company Technical Support at 1. Make sure bulbs are installed properly and filament is not blown. US 888-830-1326 / Canada 866-268-1936. 2. Make sure breakers or fuses are on. http://www.hunterfan.com 3. Verify that the light power lead is connected at the ceiling. Refer to your ceiling fan manual for locating assembly and wiring.