Download  Print this page

Sharp HT-SL72 Operation Manual

Sound bar home theater system
Hide thumbs


HT-SL72 / HT-SL77
Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read
this manual carefully. It will guide you in operating your SHARP product.
HT-SL72 SOUND BAR HOME THEATER SYSTEM consisting of TX-SL72 (Amplifier System),
CP-SW72 (Active Subwoofer System) and HT-SL72 (Sound Bar).
HT-SL77 SOUND BAR HOME THEATER SYSTEM consisting of TX-SL77 (Amplifier System),
CP-SW77 (Active Subwoofer System) and HT-SL77 (Sound Bar).
This product is recommended for flat panel TV (LED, LCD and plasma).
For HDMI connection, this product only supports PCM (Pulse Code Modulation) signals.
This product is controlled via HDMI CEC (Consumer Electronics Control) specification, therefore
for HDMI connection, your TV's CEC must be enabled. For detail, refer to the operation manual of the TV.
For TV without HDMI CEC, headphone or RCA analog connection is available.
For TV without HDMI, headphone or RCA connection is required.
This unit supports HDMI which enables Audio Return Channel (ARC).
HDMI connection and input selector are not available.
Recommended Connection:
TV Type
(with ARC)
with HDMI
HDMI TV without
CEC & ARC or non


Page 11, Method 1
Page 11, Method 2
Page 12, Method 1
Page 12, Method 2
Printed in Malaysia
12C R KI 1



  Also See for Sharp HT-SL72

  Related Manuals for Sharp HT-SL72

  Summary of Contents for Sharp HT-SL72

  • Page 1: Operation Manual

    SOUND BAR HOME THEATER SYSTEM OPERATION MANUAL Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. HT-SL72 SOUND BAR HOME THEATER SYSTEM consisting of TX-SL72 (Amplifier System), ●...
  • Page 2 52" TV x 1 for 60" TV x 1 for 70" TV x 1 (GCOVAA353AW01) (GCOVAA354AW01) (GCOVAA355AW01) (GCOVAA356AW01) HT-SL72 only Sound Bar Cover Joint Stand Cover x 2 Stand Base x 2 for 60" TV x 1 (GCOVAA330AW01) (GDAI-A016AW01) (GCOVAA360AW01) The illustrations printed in this operation manual are for the model HT-SL77.
  • Page 3: Special Notes

    Special Notes NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 4: Important Safety Instructions

    Important Safety Instructions Electricity is used to perform many useful functions, but it 17) Object and Liquid Entry - Never push objects of any kind can also cause personal injuries and property damage if into this product through openings as they may touch improperly handled.
  • Page 5: For U.s Customer Only

    Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer.
  • Page 6: Controls And Indicators

    SHARP will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified.
  • Page 7 Controls and indicators (continued) Sound Bar FRONT VIEW REAR VIEW Reference page 1. Left Front Speaker 4. Right Front Speaker Terminal (Red/Black) ..10 2. Right Front Speaker 5. Left Front Speaker Terminal (White/Black) ..10 3.
  • Page 8: System Preparation

    2. Fix the Sound Bar stand as shown. Use Sound Bar cover joint 23-3/8" (594 mm) for 70" TV. For model Use Sound Bar cover joint 14-17/32" HT-SL72 (369 mm) for 60" TV. 1. Pull out both joint covers as below. Note: Cover...
  • Page 9: Installing The Sound Bar

    Amplifier once it is attached on the wall as it can cause damage and injury. Driving screws SHARP designed the Sound Bar and Amplifier so you may Slot in the wire inside the hang them on the wall. Use proper screws (not supplied).
  • Page 10: Installing The Amplifier System

    Installing the Amplifier System Installing the Sound Bar (continued) The Amplifier can be installed as below: Screw the wall mount angle to the wall as shown in the illustration. (Total screw is 4 pieces) ● Make sure that the screw and the wall can support a load of 45 lbs (20 kg).
  • Page 11: Placing The System

    Placing the system Installation image: Notes: ● As the sound from the system is omni-directional, you can place the speaker anywhere you like. However, it is recommended to place it as close to the TV as possible. ● The front panel of the speaker is not removable. ●...
  • Page 12 For details, refer to the operation manual of the TV. ● If you are unable to select external speaker setting from the TV menu (E.g. For SHARP LCD TV, it is named as AQUOS AUDIO SP), turn the CEC OFF and ON again.
  • Page 13 System connections (continued) Connecting a TV (with AUDIO IN (TV)) Switch the input selector to ANALOG. (For HT-SL77) Connect to the TV using an audio cable. 1. Method 1 To HEADPHONE terminal Audio cable Amplifier To AUDIO IN (TV) input terminal Notes: ●...
  • Page 14: General Control

    ● “AQUOS speaker is enabled” message will be the area around the Sound Bar and Subwoofer is clear displayed if SHARP LCD TV does not detect HT-SL77 of any obstacles. during power on. However the message “AQUOS audio with AQUOS LINK is enabled” will be displayed soon as Input Selector (HT-SL77) HT-SL77 is detected.
  • Page 15: Troubleshooting Chart

    ● If something is wrong with this product, check the following Wireless connection Check the distance between the Amplifier and cannot be before calling your authorized SHARP dealer or service Subwoofer (less than 32 established. center. feet (10m)). ● Make sure there is no other...
  • Page 16: Specifications

    Specifications As part of our policy of continuous improvement, SHARP Sound Bar speaker reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal Type Full Range speaker system values of production unit.

This manual is also suitable for: