Assign The Digital Audio Connectors; General Specifications - Harman Kardon AVR 156 Quick Start Manual

AVR 156
Use the remote's left and right arrow buttons to select "On" or "Off" for each speaker
position, depending on which speakers you have connected to the receiver. When you're
finished, select "Back To Master Menu."
For now you can skip the "Sub Mode" and "Crossover" settings. For complete details
about making these settings, please download the AVR 156 Owner's Manual from www.
harmankardon.com.
5. Measure the distance from each speaker in your system to the listening position. Write
down the distances.
6. Select "Distance." The Distance menu will appear.
* DISTANCE *
FL : 3.0m
CEN : 3.0m
FR : 3.0m
SR : 3.0m
DELAY RESET : OFF
UNIT : FEET
A/V SYNC DELAY : 0mS
BACK TO SPEAKER SETUP
Use the remote's left and right arrow buttons to change the distance setting on the screen
for each speaker so it matches the distance you measured. Note: If you want, you can
change the units from meters to feet by selecting "Unit" and pressing the right arrow
button. When you're finished, select "Back To Speaker Setup."
7. Select "Level." The Level Adjust menu will appear.
* LEVEL ADJUST*
FL : 0dB
CEN: 0dB
FR : 0dB
SR : 0dB
CHANNEL RESET: OFF
TEST TONE SEQ: MANUAL
TEST TONE
BACK TO SPEAKER SETUP
Use the remote's down arrow button to select "Test Tone" and press the right arrow button
to set "Test Tone" to ON. You will hear test noise through the front left speaker.
8. Sit in the main listening position and note the volume of the test noise through the first
speaker. Press the remote's down arrow button to advance the test noise to each of your
system's speakers and note the volume level of the noise in each speaker.
9. As you advance the test noise through the speakers, use the remote's left and right
arrow buttons to adjust the volumes of the channels until all of them play at the same
volume. When you're finished, press the remote's OSD button to turn off the on-screen
menus.

Assign the Digital Audio Connectors

1. Review the input connections you listed on the
table, on page 4. Note which source devices you connected to the digital audio
connectors. (If you did not connect any source devices to the digital audio connectors,
you can skip this section.)
2. Turn on your TV and select the TV input where you connected the AVR in
TV or Video Display , on page 3.
SL : 3.0m
SUB : 3.0m
SL : 0dB
SUB: 0dB
: OFF
Input Connections and Source Buttons
Connect Your
3. Press the remote control's OSD button. The AVR's on-screen display (OSD) Master
Menu will appear on the TV.
** MASTER MENU
INPUT SETUP
SURROUND SELECT
SPEAKER SETUP
SYSTEM SETUP
4. Use the remote's arrow and OK buttons to select "Input Setup." The Input Setup menu
will appear.
* INPUT SETUP *
SOURCE
TITLE:
AUDIO IN
AUTO POLL : OFF
BXR
TONE
BASS
TREBLE
BACK TO MASTER MENU
5. For each source device you connected to a digital audio input:
a) Use the remote's up and down arrow buttons to select "Source." Use the left and
right arrow buttons to change the listed source to one of the sources you connected
to a digital audio input.
b) Use the remote's down arrow button to select "Audio In."
* INPUT SETUP *
SOURCE
TITLE:
AUDIO IN
AUTO POLL : OFF
BXR
TONE
BASS
TREBLE
BACK TO MASTER MENU
c) Use the remote's left and right arrow buttons to select the digital audio input where
you connected the source device.
When you're finished, press the remote's OSD button to turn off the on-screen menu.
You are now ready to enjoy your AVR!
IMPORTANT: For complete information about using all of your audio/video
receiver's features and capabilities, download the AVR 156 Owner's Manual from
www.harmankardon.com.

General Specifications

Power consumption: <0.5W (standby); 250W (maximum)
Dimensions (W x H x D): 17-5/16" x 6-1/2" x 17-1/16"
(440mm x 165mm x 435mm)
Weight: 20 lb (9.1kg)
Connections
**
: DVD
: ANALOG
: OFF
: IN
: 0
: 0
: DVD
: ANALOG
: OFF
: IN
: 0
: 0
7