Related Manuals for SANEI ELECTRIC ?TP-5820A
Summary of Contents for SANEI ELECTRIC ?TP-5820A
- Page 1 TP-5820A ƒÊ ƒÊ TP-5824A INSTRUCTION MANUAL Before using the printer you must read this instruction manual well for proper operation. Be sure to save this manual and keep it at hand.
- Page 2 Precautions on Handling the Printer When incorporating our product in another system or unit, the system must be so designed so that the customer's final product and system are not defective due to any faults caused by our product and the corresponding delivery must be performed. When incorporating our product in another system or unit, please consult with our sales office.
-
Page 3: Table Of Contents
Contents Before Use Parts Designation Features How to Use 1. Preparation..................4 1-1.Unpacking................. 4 1-2.Part functions ................4 1-3.Outer dimensions..............5 2.Setting roll paper ................. 6 3.Functions..................... 8 3-1.Test printing ................8 3-2.Printing mode................8 3-2-1.Front view................. 8 3-2-2.Setting correct standing printing and reversed standing printing ...... -
Page 4: Before Use
Before use CAUTION (Observe precautions for safe use) Just after printing, the printer motor becomes hot and dangerous. Do not touch it directly. Set the operating power supply to 5Vdc•}5%. An extremely high current flow may cause a fire. Precautions on Use •... - Page 5 Location l Use your printer in a horizontal to vertical place. l Using or storing your printer in the following places may cause a malfunction. Avoid places where Avoid dusty places or a Avoid places subjected to electromagnetic noise or places with exce sive strong vibration.
-
Page 6: Parts Designation
Parts Designation Mounting screw for main body fitting Main body case Main body Panel Main body fitting PAPER LED (No sheet LED) Lock lever Paper cutter Printer rear side FEED switch . I/O connector Features: uTP-5820A/24A incorporates data memory and a character generator. It is an ultra-small thermal printer that prints data input from a computer or the other host systems via a thermal-sensitive printing method. -
Page 7: How To Use
How to Use 1. Preparation 1-1. Unpacking After unpacking the product, ensure that the main body and accessories are all found. Main body (ƒÊ TP-5820A or 24A) Main body fitting Main body fitting mounting screw Thermal-sensitive paper (incorporated in the main body, P-58-15) 1 volume Instruction Manual 1 volume... -
Page 8: 1-3.Outer Dimensions
1-3. Outer dimensions Unit: mm Mount hole dimensions • Main body fitting Inner dimension:111.5 Inner dimension:99 Unit: mm... -
Page 9: Setting Roll Paper
2. Setting roll paper Roll paper can be set inside the main body. Pull the main body out from the front surface and set roll paper. When setting roll paper with the power ON, be sure to use the pull-out knob to draw the board. - Page 10 (3) Pull out roll paper to this side and turn on the power supply. While pressing the FEED switch, insert the tip of roll paper with it straight so that it can be set horizontally with the wall surface of the sheet insertion slot. Note: If paper is bent, it may cause jams.
-
Page 11: Functions
3. Functions 3-1. Test printing Turning on the power with the FEED switch pressed will result in test printing beginning after feeding paper by one line without printing. All characters are printed once, and then 10 lines of a zigzag pattern (0FEH) patterns are printed. Test printing sample Paper feeding direction... -
Page 12: And Reversed Standing Printing
3-2-2 Setting correct standing printing and reversed standing printing After turning power ON during initialization, the printer checks the correct and reverse standing printing switch on the left side of the circuit board to set correct or reversed standing printing. Note: When changing the setting, enter the reset or turn OFF the power supply once. - Page 13 [Name] Printing-paper feeding [Code]: <0A> H or <10>D [Function]: Prints data in the printer buffer and feeds paper. [Operation]: When no data is found in the printer buffer, paper is fed only. [Name] Printing/paper feeding [Code] <0D>H or <13>D [Function] Prints data in the printer buffer and feeds paper.
- Page 14 ESC +"S" + n1 + n2 + n3 + n4 + DATA [Name] Bit image mode (Graphic mode) [Code] <1B>H + <53>H + n1 + n2 + n3 + n4 + DATA or <27>D + <83>D + n1 + n2 + n3 + n4 + DATA [Function] Ordinarily, character printing is performed, but by receiving specific control...
-
Page 15: 3-4.Character Font Configuration
ESC +"c" [Name] Special character specification [Code] <1B>H + <634>H or <27>D + <99>D [Function] F9H to FDH in the character code table are changed as shown in the table below. [Operation] This is a toggle operation. Executing ESC + "c" again resumes the original state. -
Page 16: Data Code Table
4. Data code table (An undefined code is ignored.) -
Page 17: Maintenance
Maintenance CAUTION When holding the printer, take the fullest care while handling it. When the printer surface is contaminated, wipe off the contaminant with a dry soft cloth. If the contamination is severe, immerse a soft cloth in water containing a small amount of a neutral detergent. -
Page 18: Specifications
Specifications 1. General specifications 1-1. Printer specifications Printing method: Thermal-sensitive serial dot printing Type of character: Conforms to JIS-C6220, extended ASCII version (available with katakana), alphabetic characters (uppercase, lowercase), numeric figures, kana, symbols, and the like for 250 types in total Character configuration: 7 x 5 dot matrix Input character code: JIS 8-bit code (See the code table.) - Page 19 l POWER ON conditions of the internal circuit With power ON, the voltage level is detected and the circuit is initially reset under the following conditions: * Time cycle Power On Detection Reset l Resetting conditions with POWER DOWN during operation If power voltage fluctuation arises as follows, the circuit is reset like with POWER ON RESET: Reset...
-
Page 20: Interface Specifications
2. Interface Specifications 2-1. I/O connection terminals • Connector plug 4234-0001LCSC (manufactured by 3M) • I/O connector signal layout ______________________ ( Signal name is Active Low) Terminal Name Direction Description Terminal Name _________________ Input With the fall of the Return GND STROBE command signal for reading data, data is latched. -
Page 21: Input/Output Functions
2-2. Input/output functions ________________ 1. STROBE [input] Command signal for reading data At the fall of the signal, data is latched. 2. DATA0 to 7 [Input] 8-bit parallel data signal 3. BUSY [Output] Signal indicating whether or not data is acceptable. ______________ ___________ Note: During paper insertion, READY... -
Page 22: Basic Operations
2-3, Basic operations 1. Turn on the power or enter reset, and then initialize the printer. Perform unloaded feeding by one line to remove recording paper looseness. ________________ _________ 2. Enter 8-bit data from the host system by shaking the STROBE and BUSY or ACK 3. -
Page 23: Options
Options (sold separately) 1. Paper Paper is available in units of 20 rolls. Model name: P-58-15 Thermal paper black color development 2. Cables 1). PK-1 (cable 1) 34-core • Connector: HIF3BA-34D-2.54R (Hirose) • Cable length: 500 mm 2) PK-2 (cable 2) 34-core •... - Page 24 For inquiries: 171-0014 Taisou Ikebukuro Building 5F, 2-61-1, Ikebukuro, Toshima-ku, Tokyo, Japan Phone: +81-3-3986-0646 (representative) Fax: +81-3-3988-5876 Opens at 9:00 am and closes at 5:00 pm (except 12:00 to 1:00) (Closed on Saturday, Sunday and national holidays.) V1.0 0109...