Delta 36-850 Instruction Manual
  1. Manuals
  2. Brands
  3. Delta Manuals
  4. Tools
  5. 36-850
  6. Instruction manual

Delta 36-850 Instruction Manual

Stock feeder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Stock Feeder
(Model 36-850)
PART NO. 1346942 - 03-30-05
Copyright © 2005 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
1-800-223-7278 (
1-800-463-3582).
please call
In Canada call

Advertisement

Table of Contents
loading

Related Manuals for Delta 36-850

Summary of Contents for Delta 36-850

  • Page 1 Stock Feeder (Model 36-850) PART NO. 1346942 - 03-30-05 Copyright © 2005 Delta Machinery To learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com. For Parts, Service, Warranty or other Assistance, 1-800-223-7278 ( 1-800-463-3582). please call In Canada call...

  • Page 2: Table Of Contents

    NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery and we have advised you.

  • Page 3: Safety Guidelines

    SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protect- ing YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

  • Page 4: General Safety Rules

    NIOSH/OSHA approved respiratory protection appropriate for 13. USE RECOMMENDED ACCESSORIES. The use of the dust exposure, and wash exposed areas with soap and accessories and attachments not recommended by Delta water. may cause damage to the machine or injury to the user.

  • Page 5: Additional Specific Safety Rules

    ADDITIONAL SPECIFIC SAFETY RULES FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY. NEVER PERFORM LAYOUT, assembly, or set-up work DO NOT OPERATE THIS MACHINE until it is completely on the table/work area when the machine is running. assembled and installed according to the instructions.
  • Page 6 POWER CONNECTIONS A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3- prong grounding type plugs and matching receptacle which will accept the machine’s plug.

  • Page 7: Functional Description

    FUNCTIONAL DESCRIPTION FOREWORD The Delta Model 36-850 four-speed, three-roller, Stock Feeder includes a 1/4 hp, 120V single-phase reversing motor, 3 rubber feed rollers, vertical and horizontal support columns, universal joints, and an additional set of speed-changing gears and lubricating gun.

  • Page 8: Assembly

    ASSEMBLY ASSEMBLY TOOLS REQUIRED 3/8" Wrench 7/16" Wrench 4mm Hex Wrench 5/16" Wrench 1/2" Wrench Phillips Screwdriver ASSEMBLY TIME ESTIMATE Approximately 2-4 hours ATTACHING THE TABLE MOUNTING BRACKET Refer to Figs. 10, 11 and 12 when you mount the feeder assembly to a table saw, jointer or shaper. To mount the feed- er assembly: 1.

  • Page 9: Operation

    OPERATION OPERATIONAL CONTROLS AND ADJUSTMENTS FEED RATE ADJUSTMENTS Feed rates of 14, 26, 33, and 63 feet per minute (or 4, 8, 10 and 19 meters per minute) are available with the stock feeder. A gear arrangement/feed rate chart (Fig.5) is attached to the inside cover of the gear box.

  • Page 10: Operating Controls

    MACHINE USE MOTOR CONTROL SPEED SWITCH To operate the feeder in a forward position, turn switch (A) Fig. 7 clockwise. To operate the feeder in the oppo- site direction, turn switch (A) counterclockwise. OPERATING CONTROLS Disconnect machine from power source! 1.
  • Page 11 USING THE STOCK FEEDER ON A TABLE SAW Position the feeder assembly (A) Fig. 10 on a table saw so that the saw blade is between the middle roller (B) and the outfeed roller (C) and slightly angled to the direction of the feed.

  • Page 12: Troubleshooting

    SERVICE PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network • of Porter-Cable Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).

  • Page 13: Warranty

    Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection.
  • Page 14 NOTES...
  • Page 15 NOTES...
  • Page 16 Fax: (519) 767-4131 Fax: (604) 420-3522 Fax: (514) 336-3505 The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ®...

Table of Contents