Prestige Platinum APS-510C Owner's Manual

Platinum 5 button remote security system with dual stage shock sensor

Hide thumbs

Table of Contents

Quick Links

Download this manual

Page 1: Table Of Contents
Model APS-510C 5 Button Remote Security System with Dual Stage Shock Sensor Owners Guide Table Of Contents: Features and Options Page 2 Your Code Hopping Transmitters Page 3 Arming Your System- Active Page 3 - 4 Protection While the System is Armed...
Page 2: Features And Options
IMPORTANT! In order to provide the highest possible level of security to your vehicle, this system is equipped with selectable manual override circuitry. It is possible that you will need to manually override your security system if the transmitter becomes lost, or inoperative due to battery failure.
Page 3: Your Code Hopping Transmitters
YOUR " CODE HOPPING" TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your keychain transmitter, and retransmit at a later time to disarm your system.
Page 4: Protection While The System Is Armed
SILENT ARMING - ACTIVE 1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid. 2. Press and hold the Lock button on the keychain transmitter for 2 seconds.  Dash mounted LED begins to flash slowly. ...
Page 5: Disarming The System
seconds, then stop and continue to monitor all protected entry points. If the thief left a door opened, the alarm will sound for six 30 second cycles, remain armed and ignore that triggered zone.  Whenever the system is armed, the dash mounted LED indicator will slowly flash.
Page 6: While The System Is Sounding
 Headlight Illumination - Optional  Illuminated Entry Upon Disarm SILENT DISARMING 1. As you approach the vehicle, press and hold the Unlock button on the keychain transmitter for 2 seconds.  Dash mounted LED turns off. If passive arming was selected during the installation, then the LED will start flashing rapidly, indicating that the system is rearming automatically.
Page 7: Valet Override, Programming Switch (Pbled)
 If the LED is flashing one time...pause...one time...pause...etc., then an intrusion attempt was made to the shock sensor, or an accessory triggering device that may have been added to the system.  If the LED is flashing two times...pause...two times...pause...etc., then an intrusion attempt was made to a hood or trunk pin switch that was added to the system, or to a light activated entry point if the alarm was installed using the voltage sensing feature.
Page 8: Programming Your Custom Code Override
3. Within 5 seconds, press and release the PBLED override switch. The alarm system will stop sounding and enter the (bypassed) mode. You can now start and operate the vehicle normally. Typically this override mode is used only if the transmitter has become inoperative.
Page 9: Custom Code Programming Example
Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3.
Page 10: Eliminating The Normal Arm/Disarm Chirps
MANUALLY OVERRIDING YOUR SYSTEM: USING THE CUSTOM CODE OVERRIDE Assuming the override code programmed has not been changed, and the default override code of 11 is in the system's memory. 1) Enter the vehicle and turn the ignition switch to the on position. NOTE: The siren will sound.
Page 11: Optional Device Channels
1. Press and hold the ARM or DISARM button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound. 2. To stop the alarm, press and hold the ARM or DISARM button on the transmit- ter again for 3 seconds. If the button is not pressed, the alarm will automati- cally stop after 30 seconds.
Page 12: Ignition Controlled Lock/Unlock Setting
ADDITIONAL REMOTE FUNCTION ( CHANNEL 5 ) This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are;  Remote Trunk Release  Remote Car Starter ...
Page 13 For additional channel programming beyond the 1 option button, you can use any unused button or combination of buttons not in use. In other words, to access option channel 5, 6, 7, you would do the following: From step 3 above: a) Press and release the valet/programming button 4 additional times to get to channel 5, then press any unused transmitter button or button combination to program.
Page 14: Features And Function Settings
 Valet Switch Override  Illuminated Entry Upon Disarm To purchase replacement transmitters or to get additional product information go to: www.prestigecarsecurity.com © 2013 Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-8805b Page 14 128-8805b 14 of 16...
Page 15: Notes
NOTES Page 15 128-8805b 15 of 16...
Page 16 NOTES Page 16 128-8805b 16 of 16...

Prestige Platinum APS-510C Owner's Manual

Quick Links

Table Of Contents:

Related Manuals for Prestige Platinum APS-510C

Summary of Contents for Prestige Platinum APS-510C

Table of Contents