Table Of Contents - Invacare Ranger II Basic Service Manual

The procedures in this manual refer to the following models:
RANGER II MWD models: RANGER II BASIC RANGER II STANDARD RANGER II 250
RANGER II FWD models: RANGER II
Weight Shift Basic Tilt.
SPECIAL NOTES ................................................ 2
SPECIFICATIONS ............................................... 4
PROCEDURE 1 - GENERAL GUIDELINES .......... 7
REPAIR OR SERVICE INFORMATION ................. 7
OPERATING INFORMATION ............................... 7
WARNING/CAUTION LABEL LOCATION ............ 8
PROCEDURE 2- TROUBLESHOOTING ........... 12
FIELD LOAD TEST .......................................... 12
USING HYDROMETER TO CHECK BATTERY
CELLS (LEAD ACID)..................................... 12
MOTOR TESTING ........................................... 13
MOTOR BRUSH INSPECTION ......................... 14
ELECTRO-MECHANICAL PARKING BRAKE
TESTING ..................................................... 14
PROCEDURE 3 - FRONT RIGGINGS ................ 15
ADJUSTING FLIP-UP REMOVABLE
FOOTBOARD ............................................. 16
ADJUSTING THE REMOVABLE FOOTBOARD ... 16
PROCEDURE 4 - ARMS .................................... 18
REPLACING ARMREST PADS .......................... 18
REPLACING ARMREST PLATE ........................ 18
PROCEDURE 5 - SEAT/BACK ........................... 19
REPLACING SEAT POSITIONING STRAP .......... 19
REPLACING BACK UPHOLSTERY ................... 19
REPLACING CAPTAIN'S SEAT .......................... 20
PROCEDURE 6 - SEAT FRAME ......................... 21
ADJUSTING SEAT DEPTH ................................ 21
ADJUSTING BACK HEIGHT .............................. 21
CHANGING BACK ANGLE ................................ 22
REPLACING BACK CANES .............................. 22
PROCEDURE 7 - ELECTRONICS ..................... 24
REPOSITIONING MKIV JOYSTICK ..................... 24
REMOVING/INSTALLING MKIV CONTROLLER ... 24
PROCEDURE 8 - LIMIT SWITCH ...................... 27
DISCONNECTING/CONNECTING LIMIT
SWITCH ..................................................... 27
ADJUSTING LIMIT SWITCH ............................... 27
PROCEDURE 9 - WHEELS ............................... 29
REPLACING PNEUMATIC TIRES/TUBES -
DRIVE WHEELS/CASTERS ......................... 29
REMOVING/INSTALLING DRIVE WHEELS ......... 29
REMOVING/INSTALLING DRIVE WHEEL HUB .. 30
REPLACING CASTERS ................................... 32
REPLACING FORKS ....................................... 32

TABLE OF CONTENTS

RANGER II
BASIC
PROCEDURE 10 - SHROUDS ........................... 33
PROCEDURE 11 - CROSSBRACES ................ 37
PROCEDURE 12 - BATTERIES ....................... 41
PROCEDURE 13 - FWD WHEELCHAIRS .......... 46
PROCEDURE 14 - MWD WHEELCHAIRS ......... 64
LIMITED WARRANTY ....................................... 83
3
TABLE OF CONTENTS
RANGER II
STANDARD 250 Series
REMOVING/INSTALLING SHROUDS .................. 33
ADJUSTING SEAT WIDTH - INTEGRATED
SLING SEATS ............................................. 37
REPLACING CROSSBRACES - CAPTAIN'S
SEATS ........................................................ 39
INSTALLING/REMOVING BATTERIES INTO/
FROM BATTERY BOXES ............................ 41
ASSEMBLING RANGER II FWD ....................... 46
WHEN TO CHARGE BATTERIES ...................... 48
CHARGING BATTERIES ................................... 48
REPLACING BATTERIES ................................. 49
INSTALLING/REMOVING BATTERY BOXES ....... 50
BATTERY TRAY .............................................. 51
REPLACING WIRING HARNESS ..................... 55
REPOSITIONING MOTORS .............................. 59
REPLACING CLUTCH HANDLES - R2
REPLACING MOTOR/GEARBOX - R2
REPLACING MOTOR/GEARBOX -R2
ASSEMBLING RANGER II MWD....................... 64
WHEN TO CHARGE BATTERIES ...................... 66
CHARGING BATTERIES ................................... 66
REPLACING BATTERIES ................................. 67
INSTALLING/REMOVING BATTERY BOXES ....... 68
BATTERY TRAY .............................................. 69
REPLACING WIRING HARNESS ..................... 71
STABILIZER IDENTIFICATION .......................... 73
ADJUSTING SPRINGS .................................... 73
ADJUSTING STABILIZERS FOR USER
PREFERENCE ........................................... 74
REPLACING STABILIZER CYLINDERS .............. 75
REPLACING STABILIZER WHEELS ................... 76
REPLACING STABILIZER CYLINDER SPRINGS .. 77
REPOSITIONING MOTORS .............................. 78
REPLACING CLUTCH HANDLES
-R2 /R2
.....................................................................
BASIC 250 series
REPLACING MOTOR/GEARBOX -R2
REPLACING MOTOR/GEARBOX -R2
.
SERIES
and RANGER II with
60
.................
BASIC
61
................
BASIC
62
......
STANDARD
78
79
.................
BASIC
80
........
STANDARD
T
A
B
L
E
O
F
C
O
N
T
E
N
T
S