Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Compaq S7300CL
Summary of Contents for Compaq S7300CL
- Page 1 Compaq Presario Desktop Products Upgrading and Servicing Guide...
- Page 2 HP shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
-
Page 3: Table Of Contents
table of contents upgrading and servicing the pc ... 1 preparing the pc ... 1 removing or upgrading a drive ... 2 upgrading or replacing memory ... 7 removing or installing an expansion card ... 8 reassembling the pc ... 10 locating drive positions...3 removing a drive ...3 replacing or adding a drive ...5... - Page 4 Upgrading and Servicing Guide...
-
Page 5: Upgrading And Servicing The Pc
upgrading and servicing the pc This guide describes procedures for accessing the internal parts of the PC and installing components. NOTE: The procedures for the S0000 and 8000 series models are the same except where noted. 8000 series model and S0000 series model preparing the pc Before you upgrade any component in your PC, you need to prepare the PC so that you can safely handle... -
Page 6: Removing Or Upgrading A Drive
removing the pc access panel on the 8000 series 8 Remove the front bezel by following the appropriate method for your PC model: • To remove the front bezel from the S0000 series model, gently pry the top section (1) of the bezel away from the chassis. -
Page 7: Locating Drive Positions
locating drive positions 1 Optical drive, may be a CD-ROM, CD-RW, DVD-ROM, or DVD+RW/+R drive 2 Second optical drive, may be a DVD-ROM, DVD+RW/+R, CD-ROM, CD-RW drive, or 7-In-1 memory card reader (select models only) 3 Diskette (floppy) drive 4 Hard disk drive drive positions on the S0000/8000 series (S0000 shown) removing a drive... - Page 8 disconnecting the hard disk drive cables 4 Release the drive from the chassis by following the method appropriate for your PC model. • To release a drive from the chassis of the S0000 series, lift the release tab (1) on the latch drive bracket of the drive you want to remove, and then slide the drive from its drive bay (2).
-
Page 9: Replacing Or Adding A Drive
If you have the S0000 series, and you NOTE: removed a 7-In-1 memory card reader, continue to step 7; otherwise, you are finished with the task of removing a drive from the chassis. If you have the 8000 series and you removed a hard disk drive, a 7-In-1 memory card reader, or an optical drive, you are also finished with this task. - Page 10 2 Slide the drive into the drive bay (1), making sure to align the guide screws with the guide slots, until it snaps into place. sliding the drive into the drive bay on the S0000/8000 (S0000 shown) 3 Reconnect the power and data cables to your drive as indicated in the following illustrations.
-
Page 11: Upgrading Or Replacing Memory
2 Press inward on each side of the bracket brace (3), and lower the bracket until it snaps into place over the diskette drive. Ensure that the guide screws (4) are installed in the adapter. 3 Return to “replacing or adding a drive” on page 5, and begin with step 1. -
Page 12: Replacing Or Adding A Memory Module
replacing or adding a memory module Upgrade the memory in your PC with memory of the same type and speed as the memory originally installed in your PC. CAUTION: When handling a memory module, be careful not to touch any of the contacts. -
Page 13: To Install An Expansion Card
to remove an expansion card 1 Complete the procedure described in “preparing the pc” on page 1, but do not remove the front bezel. • To remove an expansion card from the S0000 series, continue to step 2. • To remove an expansion card from the 8000 series, skip to step 3. -
Page 14: Reassembling The Pc
• If you have an 8000 series, continue to step 2. • If you have an S0000 series, skip to step 3. 2 For the 8000 series, secure the expansion card to the chassis with the slot cover screw. 3 For both the S0000 and 8000 series, if you have replaced an expansion card, store the old card in the anti-static packaging that contained your new card. - Page 15 replacing the side access panel on the S0000 series replacing the side access panel on the 8000 series 3 Reconnect the power cable (1) to the PC, and plug the cable into an electrical outlet (2). reconnecting the power cable on the S0000/8000 (S0000 shown) 4 Reconnect the modem/telephone cable, if present.
- Page 16 Printed in...
Need help?
Do you have a question about the S7300CL and is the answer not in the manual?
Questions and answers