Rear Panel Installation Features; Video And Audio Connections, Sync Termination, And External Sync - Extron electronics CrossPoint 450 Plus Series Setup Manual

Installation
*
3
ANAHEIM, CA
OUTPUTS 1 - 16
1 2 3 4
1 2 3
1 2 3 4 5 6 7 8
75
5 6 7 8
510
9 10 11
10 12 14 16
9 11 13 15
75
9 10 11 12
510
17 18 19
13 14 15 16
25 26 27
33 34 35
OUTPUTS 17 - 32
17 18 19 20
41 42 43
21 22 23 24
49 50 51
25 26 27 28
57 58 59
29 30 31 32
LISTED
1T23
C U S
I.T.E.
*
* Sync BME only
11 2
MAV Plus video BME only
G
Figure 2-1 — Sync or video BME
C
11
Figure 2-2 — Audio BME
2-2 CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / MAV Plus User's Manual at www.extron.com.
1
OUTPUTS 33 - 48
33 34 35
INPUTS
4 5 6 7 8
37 38 39
12 13 14 15 16
41 42 43
20 21 22 23 24
45 46 47
28 29 30 31 32
36 37 38 39 40
OUTPUTS 49 - 64
49 50 51
44 45 46 47 48
53 54 55
52 53 54 55 56
57 58 59
60 61 62 63 64
61 62 63
REMOTE
EXT BME
ADDRESS LAN
SYNC BME COMM
Tx
-
Tx Tx Rx
4
Rx Rx +
ACT LINK
IN OUT RESET RESET
G
4 10 9 8 7
5
6

Rear Panel Installation Features

36
40
44
48
2
52
Video and audio connections, sync termination,
56
and external sync
60
64
7
8
9
10
Extron recommends locking redundant front panel
N
controllers (if included in your system). See page 3-4.
Only sync BMEs have sync termination switches.
N
Only MAV Plus video BMEs have External Sync connectors.
N Smaller matrix sizes have fewer input connectors, output
connectors, or both.
C Turn off power to the input and output devices, and
disconnect their power cords.
a
Video inputs — Connect RGBHV, RGBS, RGsB, RsGsBs,
component/ HDTV video, S-video, or composite video sources,
as appropriate to your switcher system's video format and
matrix size.
b
Video outputs — Connect RGBHV, RGBS, RGsB, RsGsBs,
component/HDTV video, S-video, or composite video displays,
as appropriate to your switcher system's video format and
matrix size.
c
Sync termination switches (sync BMEs only) — Set the switches
as necessary to condition non-TTL sync levels greater than 5 Vp-p
for inputs 1 through 16 only. Sync termination enables the sync to
be properly passed from an input to the selected output(s).
510 ohms — The default position, suitable for most video.
75 ohms — Typically required only for an input with non-TTL
sync (greater than 5 V p-p).
N An input that produces an out of sync display, a display
that is rolling vertically and/or tearing horizontally, could
indicate a non-TTL sync input. If you are not sure, check
the specifications in the user's manual for the input device.
d
External Sync (MAV Plus video BME) — If desired, attach an
external sync timing device to the external sync connector.
BBG 6 A
BLACK BURST/COLOR BAR
/AUDIO GENERATOR
1 3 5
POWER
1 KHZ AUDIO
12V
+4dBu
0.5A MAX
L 1 R
ON
1 2 3
2 4 6
BLACKBURST/
-10dBV PAL COLORBAR BLACKBURST
OUT
Extron BBG 6 A
Black Burst Color Bar
Audio Generator
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / MAV Plus User's Manual at www.extron.com.
EXT
SYNC
Connect to
MAV Plus.
Terminate cable
or connect to
another device.
2-3