Steelmate PTS800V7 User Manual

Front & rear parking assist system top front windshield display

Advertisement

Front & rear
Parking assist system
PTS800V7
Top front windshield display
Manual
BRM061

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PTS800V7 and is the answer not in the manual?

Questions and answers

Summary of Contents for Steelmate PTS800V7

  • Page 1 Front & rear Parking assist system PTS800V7 Top front windshield display Manual BRM061...
  • Page 2: Table Of Contents

    Contents User's Manual Installation Manual Important notice ---------------------------------------- Brief installation diagram ---------------------------- Disclaimer ----------------------------------------------- Packing list ---------------------------------------------- About the product ------------------------------------- Installation tools ---------------------------------------- Key features -------------------------------------------- Sensor installation ------------------------------------- Technical specifications ------------------------------ Display installation ------------------------------------ LCD display --------------------------------------------- Wire connection ---------------------------------------- Voice and volume adjustment ---------------------- Function test after installation ---------------------- Self-test function ---------------------------------------...
  • Page 3: User's Manual

    Self-test function technician. Voice / beep alert selectable PTS800V7 is a front and rear parking assist system Intelligent detection, supper for cars with 3. Route wiring harness away from heat sources with blue wide LCD display. All the detachable...
  • Page 4: Voice And Volume Adjustment

    Display Voice and volume adjustment Turning ON/OFF voice alert Matrix indication (front) ACC ON Meters Press "SET" once Voice alert turned off START Volume Distance Damaged sensor indication Matrix indication (rear) Press "SET" button Ignition on seconds. (Front view) Press "SET"...
  • Page 5: Self-Test Function

    Self-test function Learning function for cars with tow-bar or spare wheel 1. Once the ignition is turned on, the system will test the 4 front sensors E,F,G and H automatically. 1) All sensors are working. 2) Damaged sensors are detected. Beep three times Be...Be...Be...
  • Page 6: How Does The System Work

    How does the system work Driving forward (6 sensor) Driving forward (8 sensor) +12V +12V +12V +12V +12V +12V 0.81m/2.6ft 0.40m/1.3ft Stop(<0.30m/1.0ft) 0.81m/2.6ft 0.35m/1.1ft Stop(<0.30m/1.0ft) No beep No beep...
  • Page 7 Reversing Zigzag reversing 0.30m/1.0ft Stop! (<0.30m/1.0ft) 1.21m/4.0ft 0.60m/2.0ft Stop(<0.30m/1.0ft) Be-Be-Be-Be- Be---Be---...
  • Page 8: Attention

    Attention Sensor maintenance False detection may occur in the following situations: Do not wash the sensor with squirt gun or swab them forcibly. Installation Manual Please wash car with low-pressure water. Please melt the ice with warm water when the sensors are covered by ice.
  • Page 9: Brief Installation Diagram

    Brief installation diagram Packing list The actual sensor may vary from the image shown above Display Installation tools 60' ~ 80'...
  • Page 10: Sensor Installation

    Sensor installation Pls adjust the sensor angle according to sensor height and bumper angle, avoid detecting to ground. H > 45cm/1.5ft H < 65cm/2.1ft H > 40cm/1.3ft H < 60cm/2.0ft < 45cm/1.5ft < 45cm/1.5ft < 45cm/1.5ft 2.5m /0.8ft 0.9m /3.0ft 35cm/1.1ft <L1<...
  • Page 11 Check the size of the hole saw packed in the product to be matching the diameter of the sensors before drilling any holes.
  • Page 12 Power Reversing light + Check the size of the hole saw packed in the product to be matching the diameter of the sensors before drilling any holes.
  • Page 13: Display Installation

    Display installation Wire connection Display E F G H A B C D Pink Reversing light White Footbrake light Black wire Ground Sensor D Sensor C Sensor B Sensor A Sensor H Sensor G Sensor F Sensor E...
  • Page 14: Function Test After Installation

    Function test after installation Troubleshooting After installation, the display doesn’t work The display always shows 0.4/15.7ft~0. a) Are all wires connected properly? 6m/23.6ft. b) Is the ignition turned on? a) Are sensors mounted too low or detecting the c) Is the reverse gear selected or is the footbrake ground? pressed? b) Check whether the sensor is installed up-side-...

Table of Contents