Table of Contents
Related Manuals for Steelmate PTS600MM
Summary of Contents for Steelmate PTS600MM
- Page 1 PTS600MM PTS800MM Parking Assist System Front & Rear Protetion All rights reserved The trademark, patent and copyright are owned by Steelmate Co., Ltd. The right to change the design and specifications for improving the product is reserved...
-
Page 2: Table Of Contents
User's Manual Installation Manual User's Manual slowing down, use of mirrors etc. are always essential. Reasons to choose Steelmate ----------------------- Brief installation diagram ------------------------------ 1. This unit is for vehicles with 12V DC only. Important notice ------------------------------------------ Packing list ------------------------------------------------- 2. -
Page 3: About The Product
~ +80°C/-40°F~+185°F) meaning it will still continue Front display Beep volume: 70 ~ 90 dB to function when you are parking on a raining day, snowing day or at night etc. With the help of Steelmate Display range: Front 0.3m ~ 1m/1ft ~ 3.2ft Rear display... -
Page 4: Volume Adjustment
Self-test function Volume adjustment Front display When the ignition is turned on, the system will test the front sensors E, F, G and H automatically. If a damaged or defective sensor is detected, then the system will: Beep three times. The locations of the damaged or defective sensors will be shown on the display Other sensors will continue to function normally Once the self-test procedure is completed, the system will detect the obstacle in front of the car for 30 seconds. -
Page 5: Learning Function
Learning function How does the system work Driving forward Learning function for cars with front metal bar Turn the ignition on, press the footbrake and connect the green learning wire (located in the main front ECU No beep Be ** Be ** Be **** wiring loom) to a +12V power supply. - Page 6 Zigzag reversing Reversing Be **** Be--Be--Be-- No beep Be--Be--Be-- No beep Distance: <0.3m/0.9ft Distance: 0.5m/1.5ft Distance: 1m/3.2ft Distance: 0.4m/1.3ft Distance: 0.6m/1ft No beep Be-Be-Be-Be- Be **** Be **** Be-Be-Be-Be- Distance: >1.5m/4.9ft Distance: 0.8m/2.6ft Distance: < 0.3m/0.9ft Distance: 0.6m/1.9ft Distance: 0.3m/0.9ft...
-
Page 7: Attention
Attention Sensor maintenance Troubleshooting False detection may occur in the following After installation, the display doesn't work 3) Plug the certified sensors into the ECU and situations: a) Are all wires connected properly? recheck. b) Is the vehicle's ignition ON? 4) Email your question to us and we will reply ASAP. -
Page 8: Warranty Terms
Warranty terms Damage to the system caused by accident or The unit is warranted for a limited period of time from the date of purchase. In the unlikely event improper use in any manner whatsoever not the fault, including but not limited to damage of a defect arising in this product when used in by water or as a result of excess voltage... -
Page 9: Brief Installation Diagram
Brief installation diagram Rear display Rear display Front display Reversing Reversing light light Rear ECU Rear ECU Front display Radio mute wire Radio mute wire Footbrake Footbrake Front ECU Front ECU... -
Page 10: Packing List
Sensor installation Packing list H > 45cm/1.5ft H < 60cm/2.0ft * The actual sensor may vary from the image shown above * Your product may be any two from the three displays shown above. Installation tools H < 45cm/1.5ft 35cm/1.2ft<L1<45cm/1.5ft H >... - Page 11 H > 45cm/1.5ft H < 65cm/2.1ft < 45cm/1.5ft < 45cm/1.5ft < 45cm/1.5ft H < 45cm/1.5ft Check the size of the hole saw packed in the product to be matching the diameter of the sensors before drilling any holes. H > 65cm/2.1ft = 1/8L = 2/8L = 1/8L...
-
Page 13: Display Installation
Display installation Rear display installation Front display installation Installation steps for M5 1. Remove the paper liner from 3M adhesive 2. Stick the display to a desired location. * The display can be one of the three displays shown above depending on the product ordered. pad on the display. -
Page 14: Installation Diagram
Installation diagram Front unit: Installation steps for M6 and M8 4-front-sensor system Pink (ACC) Red (Reversing light +12V) Positive output (+) White (Footbrake light + 12V) Negative output (-) Blue (Radio mute wire) Green (Learning wire) Black (GND) 1. Fix the display with two screws. 2. - Page 15 2-front-sensor system 2-front-sensor system Pink (ACC) Pink (ACC) Red (Reversing light +12V) Red (Reversing light +12V) Positive output (+) Positive output (+) White (Footbrake light + 12V) White (Footbrake light + 12V) Negative output (-) Negative output (-) Blue (Radio mute wire) Blue (Radio mute wire) Green (Learning wire) Green (Learning wire)
-
Page 16: Function Test After Installation
Function test after installation Rear unit: Function test is possible by holding a wooden board (30 x100cm/1x3.3ft) standing at the front or rear of the car, and drive the car forward and backward to t e s t e a c h f u n c t i o n respectively as shown in PARKING ASSIST SYSTEM...
Need help?
Do you have a question about the PTS600MM and is the answer not in the manual?
Questions and answers