Page 1
7” ElEctric PolishEr / sandEr Model 41213 sEt UP and oPErating instrUctions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. ® distributed exclusively by harbor Freight tools 3491 Mission Oaks Blvd., Camarillo, CA 93011...
Notice Notice related to personal injury. caUtion, without the safety alert symbol, caUtion caUtion is used to address practices not related to personal injury. SKU 41213 For technical questions, please call 1-800-444-3353. Page 2...
Use safety equipment. always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protec- tion used for appropriate conditions will reduce personal injuries. SKU 41213 For technical questions, please call 1-800-444-3353. Page 3...
Page 4
Use of the power tool for operations different from those intended could result in a hazardous situation. SKU 41213 For technical questions, please call 1-800-444-3353. Page 4...
Prepare to begin work before turning on the tool. do not lay the polisher down until it has come to a complete stop. Moving parts can grab the surface and pull the tool out of your control. SKU 41213 For technical questions, please call 1-800-444-3353. Page ...
Page 6
Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. SKU 41213 For technical questions, please call 1-800-444-3353. Page ...
Page 7
It must be understood by the operator that common sense and caution are fac- tors which cannot be built into this product, but must be supplied by the operator. saVE thEsE instrUctions. SKU 41213 For technical questions, please call 1-800-444-3353. Page 7...
Page 8
Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Stan- SKU 41213 For technical questions, please call 1-800-444-3353. Page ...
Always replace a damaged extension cord or have it repaired by a qualified elec- trician before using it. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas. SKU 41213 For technical questions, please call 1-800-444-3353. Page 9...
Page 10
* Based on limiting the line voltage drop to five volts at 150% of the rated amperes. symbology Double Insulated Volts Alternating Current Canadian Standards Association Amperes No Load Revolutions per Minute n 0 xxxx/min. Underwriters Laboratories, Inc. (RPM) SKU 41213 For technical questions, please call 1-800-444-3353. Page 10...
Flange Nut (47). Loosen and remove the Flange Nut (47) by turning it coun- terclockwise. Set the Backing Pad (4) on the Output Shaft (42). Replace the Flange Nut (47) by turning it clockwise. SKU 41213 For technical questions, please call 1-800-444-3353. Page 11...
Page 12
For sanding, place a sanding disk with a hole in the center onto the Backing Pad and secure it with the Flange Nut (47). See Figure 1 below. Figure 1 Flange Nut (47) Backing Pad (46 ) Output Shaft (42) Stop Pin (3) Housing (16) Side Handle (34) Figure 2 Polishing Bonnet (48) SKU 41213 For technical questions, please call 1-800-444-3353. Page 12...
Always start and stop the Polisher while it is held firmly against the surface of the vehicle. Failure to do so may result in the Bonnet being thrown from the Backing Pad (4). SKU 41213 For technical questions, please call 1-800-444-3353. Page 13...
Page 14
When finished, release the Switch (24) to its OFF position. Then unplug the Power Cord (33) from the electrical extension cord. Unplug the extension cord from the electrical outlet. Store in a dry area. SKU 41213 For technical questions, please call 1-800-444-3353. Page 14...
Page 15
When finished, release the Switch (24) to its OFF position. Then unplug the Power Cord (33) from the electrical extension cord. Unplug the extension cord from the electrical outlet. Figure 2 15 to 25 Degrees SKU 41213 For technical questions, please call 1-800-444-3353. Page 1...
Check that cord is plugged in. MaintEnancE chart before after Every 6 Maintenance type Weekly Monthly Yearly Months Inspect tool for damage (see #1, above) Wipe off with clean, moist cloth SKU 41213 For technical questions, please call 1-800-444-3353. Page 1...
Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 41213 For technical questions, please call 1-800-444-3353. Page 1...
TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND record Product’s serial number here: note: If product has no serial number, record month and year of purchase instead. SKU 41213 For technical questions, please call 1-800-444-3353. Page 19...