Advertisement
7" POLISHER/SANDER
Model 46507
ASSEMBLY AND
OPERATING INFORMATION
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright
2001 by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions please call 1-800-444-3353
Advertisement
Table of Contents
Related Manuals for Chicago Electric CHICAGO 46507
Summary of Contents for Chicago Electric CHICAGO 46507
- Page 1 2001 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions please call 1-800-444-3353...
-
Page 2: Specifications Table
USE EYE, BREATHING, AND HEARING PROTECTION. Wear ANSI approved safety impact eye glasses, ANSI approved breathing protection, and ANSI approved hearing protection when using this product. ANSI approved safety impact eye glasses, dust masks, and hearing protectors are available from Harbor Freight Tools. SKU 46507 SPECIFICATIONS TABLE Description... -
Page 3: Specific Product Warnings And Precautions
REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. MAINTAIN THIS PRODUCT WITH CARE. Keep this tool clean and dry for better and safer performance. - Page 4 DO NOT FORCE THE EQUIPMENT. This Polisher/Sander will do the work better and safer at the speed and capacity for which it was designed. REMOVE ALL ADJUSTING WRENCHES FROM THE POLISHER/SANDER BEFORE TURNING IT ON.
- Page 5 When unpacking, check to make sure all parts shown on the Parts List (page 11) are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
-
Page 6: Assembly Instructions
Carefully inspect the condition of the accessory before use and check the accessory continually during use. If any damage is noted, stop immediately and replace the accessory with an undamaged one. Harbor Freight Tools cannot be held responsible for damage caused by using a damaged accessory on this tool. -
Page 7: Operating Instructions
Polisher/Sander. (See Figure C, and Assy. Diagram.) To attach the Side Handle (part #20), remove the Rubber Plunge (part #19) from either the right, left, or top side of the Polisher/Sander in order to expose the threaded mounting hole. (See Figure C, and Assy. Diagram.) Firmly hand tighten the threaded portion of the Side Handle (part #20) into the desired mounting hole of the Polisher/Sander. - Page 8 To Attach The Rubber Backing Plate And Sandpaper: Caution: Prior to installing the Rubber Backing Plate (part #46), make sure the Polisher/Sander is disconnected from its electrical power source. Rest the tool on a flat surface. Depress the Brake Pin (#18) to keep the Spindle (#3) from turning.
-
Page 9: Inspection, Maintenance, And Cleaning
Power Cord (part #36) into a 110-120 Volt, grounded, electrical power outlet. (See Figures B, C, and Assy. Diagram.) Make sure to use both hands to firmly grip the Polisher/Sander by its Side Handle (part #20) and Back Handle (part #39). (See Figures B, C, and Assy. -
Page 10: Please Read The Following Carefully
If there are large scratch marks in the Brushes, or parts of the Brushes have broken off, replace both Brushes immediately with approved replacement Brushes from Harbor Freight Tools. To reinstall the Brushes, insert them into the two Brush Holders (part #42). Turn the Brushes vertically so they will fit into the Brush Holders. -
Page 11: Parts List
PARTS LIST Adaptor Wool Compounding Bonnet Rubber Backing Plate REV 09/02 SKU 46507 PAGE 11... - Page 12 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 46507 PARTS LIST PAGE 12 For Polishing Note: #45 includes Arbor Nut 5/8” - 11 TPI. For Sanding REV 09/02...