Fujioh BUF-06W Installation Manual

Range Hood

INSTALLATION MANUAL

SAFETY INSTRUCTIONS

Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.
WARNING:
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION:
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
CAUTION:
CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.
NOTE: The safety instructions are explained with the following
pictographic symbols.
means prohibition. It indicates actions, if any,
that mustn't be done.
means forcible execution. It indicates actions, if
any, that must be done.
WARNING
1. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning the unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
2. To reduce the risk of fire or electric shock, do not
use this product with any solid-state speed control
device.
3. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Installation work and electrical wiring must be
done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-
rated construction.

1. Preparation

WARNING:
• Ensure that the metal duct does not touch other metal housing
materials, otherwise fire or electric shock could result.
1
This range hood is Roof cap
designed to discharge
7" round duct
upward. For vertical
(For vertical discharge)
discharge, run duct work
between the hood location
and roof cap location.
To get the best result, use
a minimum number of
Soffit
transitons and elbows.
Be sure to attach a roof
cap to avoid rain from
entering the exhaust duct.
Range hood
2
The range hood unit must be mounted to a liner which has the
following dimensions. Install the liner securely after checking that
the opening size of the liner is the same as the figure below.
4-∅1/4" (4-∅6.5)
25-3/16" (640)
26" (660)
Unit: inch (mm)
CAUTION:
• The liner should be installed tightly. If the liner installation is not
correct, the range hood unit may become detached and fall.
3
Make sure that a wood panel for
mounting the range hood is fixed
Wood panel
on the wall where the range hood
is installed.
Note: If no wood panel is found
on the wall, be sure to
prepare one referring to the
figure.
Fan unit
Liner
4
Referring to "DIMENSIONS" above,
5mm
insert 2 supplied wood screws into
the mounting wall for the left and
right hangers. Allow about 5mm
space between the wall and screw-
heads for hanging.
b) Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer's
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and The American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
c) When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
d) Ducted fan must always be vented to outdoors.
4. TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
5. This unit must be grounded.
6. Install this range hood to a liner. Check that the
hood is correctly installed, since incorrect
installation could result in the range hood
becoming detached and falling off.
7. Connect only to an AC120 Volt power source or
the range hood could result in fire, electric shock,
and damage.
CAUTION
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive material and
vapors.
2. To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls, ceilings or into attics,
crawl spaces or garages.
3. Read specification label on this product for further
information and requirements.
4. Use only for the purpose of kitchen ventilation.
5. Do not install this range hood in the bathroom or
in other wet rooms since electrical shock and
damage may result.
6. Fasten the filter and other parts securely. Incorrect
attachment may result in personal injury or
property damage.

INSTALLATION

2. Range Hood Mounting

CAUTION:
• Wear working gloves to avoid injury.
1
Detach the tape on the exhaust port.
2
Detach the filters by loosening 2 screws. Remove 5 screws
fixing the front cover and detach the front cover.
Screw
3
Hold up the range hood and align the 4 screw holes of the liner
and range hood, then fix securely using the supplied screws
(M5×30) and nuts.
Note: Fasten all the screws and nuts evenly.
Liner
Securing plate
[Securing plate turns
while passing through
the opening of Liner]
Four screws (M5×30)
4
With inserting the exhaust
port into the duct, hook
both the left and right
hangers on the screws
provided in "Preparation"
step 4.
5
Tighten both the left and
right screws, and fix the
Wall
Tighten screws to fix
range hood securely
adding 4 more supplied
washer head wood
screws to the holes on
the hangers and back of
the range hood.
6
Make the duct joint secure
and air-tight using non-
flammable tape such as duct
tape, etc. (Not supplied)
Non-flammable tape
MODEL: BUF-06W

NAMES OF PARTS

Lamp Switch
Fan Switch
Filter
DIMENSIONS
∅ ∅
7/8"( 22.6)
8-9/16"(217.5)
26" (660)
∅ ∅
4- 1/4"(4- 6)
16-3/8"(415.2)
11"(279.3)
19-13/16" (503.3)
26-3/4" (680) 16-5/8"(423)
27"(686)
17-11/16"(450)
12-3/8"(314) 12-3/8"(314)

3. Connecting Power Supply Wires

WARNING:
• Electrical wiring should be done by a qualified person(s) in
accordance with all applicable codes and standards, including
fire-rated construction. An unqualified person doing the work could
result in fire, electric shock or injury.
• This range hood uses 120V AC. Do not connect to other voltage
since fire, electric shock or damage could result.
1
Remove the nut from the conduit
Tape
connector at the end of power wiring.
WARNING:
Be sure to switch power OFF at
service panel before wiring.
2
Remove one screw fixing the
wire cover and detach it.
Screw-washer
[Right & left,
3
each two (2) places] Connect the conduit through the connecting hole of the body
using the nut previously removed.
Liner
4
Connect wires tightly and securely using wire connectors
(not supplied).
Connect the electrical wires as follows:
Hanger
• Black to Black
• White to White
• Green to Green
5
Replace the wire cover with
the screw removed previously.
Make sure that all wires are
connected properly and
enclosed inside of the wiring
compartment.

CIRCUIT DIAGRAM

Front Cover
Enclosure
Connector
White
120V
Black
60Hz
Green
Black
Capacitor
Unit: inch (mm)

RANGE HOOD LOCATION

14-5/8"(371.5)
or
16-1/8"(410)
6-5/16"(160)
∅ ∅
6-15/16"( 176) 1
The range hood must
9/16"(14)
be installed just above
the cooktop.
2
The minimum distance
19-11/16"(500)
from the cooking
surface to the bottom of
the range hood must
be 24".
3
The total weight of the
BUF-06W range hood
unit is 35.2 lbs. (16 kg)
4
Power requirements are:
AC120 V, 60 Hz,
3.0 Amp
CAUTION:
• Check that the hood is correctly installed, since incorrect
installation could result in the detachment of the range
hood and the unit could fall.
• To protect hands from injury, wear working gloves when
installing the range hood.

4. Final Assembly and Check

1
Assembly
Attach the front cover, and secure it with 5 screws.
Then attach the filters.
Conduit
(Not supplied)
Screw
Nut
(Not supplied)
Two 50 W halogen light bulbs (not supplied) can be mounted in
this range hood.
Prior to function check, install light bulbs (PAR20 bulb, in the base
diameter 26 mm: medium base), rated 120 V - 50 W or below.
Turn the lamps clockwise to install them.
Bulb
(Not supplied)
2
Check
(1) Turn on the electrical circuit to the range hood.
(2) Make sure that the switchs and light operate correctly.
Refer to page 4 of the Operation Manual.
(3) Make sure that the range hood functions properly and it has
no abnormal noises and/or vibration.

5. Explanation to the End User

(1) Referring to the Operation Manual, explain the operation of this
range hood to end users.
(2) The Installation Manual and Operation Manual should be given to
the end user.
1U03 1381
Lamp Switch Fan Switch
Connector
Pilot Lamp
Connector
Black White
Grey Yellow
Black
Lamp
Yellow Yellow
Motor
White White
Black
Black
Connector
Connector
White
White
Black
Black
Connector Lamp
White
ACCESSORIES
Screw M5.1×45
Four (4) pieces
Screw M4.5×45
Two (2) pieces
Screw M5×30
Four (4) pieces
Nut with plate
Four (4) pieces
Liner
24" (Minimum)
Cook top
Push to turn ON