Table of Contents
Advertisement
Quick Links
Installation Manual
RANGE HOOD
MODEL: BUF-07W
BUF-07P
Safety Instructions ................................................................................................ 2, 3
Name of Parts .......................................................................................................... 4
Circuit Diagram ........................................................................................................ 4
Dimensions/Accessories ...................................................................................... 5, 6
Range Hood Location .............................................................................................. 7
Installation .......................................................................................................... 8~22
1. Preparation .................................................................................................. 8, 9
2. Range Hood Mounting ............................................................................... 9~17
Mounting Procedure for BUF-07W (Wall Mounting) ............................... 9~13
Mounting Procedure for BUF-07P (Ceiling Mounting) ......................... 14~17
3. Connecting Power Supply Wires .............................................................. 18, 19
4. Final Assembly and Check ....................................................................... 19~22
5. Explanation to the End User by Installer ........................................................ 22
READ AND SAVE THESE INSTRUCTIONS.
Keep this manual in a convenient place for future reference.
TABLE OF CONTENTS
FUJI INDUSTRIAL CO., LTD.
BUF-07W/P
1U03 3081
*1U033081*
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Fujioh BUF-07W
Summary of Contents for Fujioh BUF-07W
-
Page 1: Table Of Contents
Installation ......................8~22 1. Preparation ....................8, 9 2. Range Hood Mounting ................9~17 Mounting Procedure for BUF-07W (Wall Mounting) ....... 9~13 Mounting Procedure for BUF-07P (Ceiling Mounting) ......14~17 3. Connecting Power Supply Wires .............. 18, 19 4. Final Assembly and Check ............... 19~22 5. -
Page 2: Safety Instructions
SAFETY INSTRUCTIONS Before installation and operation, read these instructions carefully and use this product only in the manner described by the manufacturer in the operation manual. The instruction shown below are used to alert you to potential personal injury and property damage hazards. There are three hazard classifications based on potentially dangerous situations. - Page 3 CAUTION 1. For general ventilating use only. Do not use to exhaust hazardous or explosive material and vapors. 2. To reduce the risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls, ceilings or into attics, crawl spaces or garages.
-
Page 4: Name Of Parts
NAME OF PARTS Enclosure BUF-07W/P Lamp (Not supplied) (PAR20 bulb, in the base diameter 26mm: medium base) Front Cover Filter Hanging Bracket (only W model) Lamp Switch Fan Switch Pilot Lamp Lamp Switch OFF Switch High Switch Low Switch Medium Switch... -
Page 5: Dimensions/Accessories
DIMENSIONS/ACCESSORIES BUF-07W (Unit : inch) 26" 15-3/4" 6-5/8" 5/8" 7-7/8" ∅ 14-5/8" 7/8" 10" 25-1/16" 19-11/16" 27" 17-11/16" 12-3/8" 12-3/8" Accessories Screw M5.1×45 Screw M5×30 Screw M5×10 Screw M4×10 Six (6) pieces Four (4) pieces Four (4) pieces Four (4) pieces... - Page 6 DIMENSIONS/ACCESORIES (continued) BUF-07P (Unit : inch) 26" 16-15/16" 15-11/16" 6-5/8" 5/8" 7-7/8" ∅ 7/8" 25-1/16" 12" 10" 27" 17-11/16" 12-3/8" 12-3/8" Accessories Screw M5×30 Screw M4×8 Four (4) pieces Four (4) pieces Nut with plate Mounting bracket Four (4) pieces One (1) piece...
-
Page 7: Range Hood Location
The minimum distance from the cooking surface to the bottom of the range hood must be 24”. Liner 24" (Minimum) Cook top The total weight of the BUF-07W and BUF-07P range hood unit are; BUF-07W: 50.9 lbs. (23 kg) BUF-07P: 50.9 lbs. (23 kg) Power requirements are: AC120 V, 60 Hz, 8.7 Amp WARNING •... -
Page 8: Installation
Note: 10" round duct Note: 10" round duct Soffit Wall cap Wall cap Duct Duct (For holizontal discharge) (For holizontal discharge) Soffit Note: 10" round duct Note: 10" round duct Range hood 3/4" thickness wood panel is required BUF-07W BUF-07P... -
Page 9: Range Hood Mounting
During installation, be careful not to touch the fan switches. If two or more switches are pushed at once, it may cause failure to the motors. Mounting procedure for BUF-07W (Wall Mounting) *For the procedure to mount BUF-07P (Ceiling Mounting), see page 14. 3/4" thickness... - Page 10 INSTALLATION (continued) Place the range hood as shown and Front cover detach the left and right filters by loosening 2 screws. Then remove 5 screws fixing the front cover and detach the front cover. Filter Loosen 2 screws to remove the filter. Remove the sound-absorbing boxes.
- Page 11 INSTALLATION (continued) Remove the fan unit. Push with a screwdriver etc, and pull off. Screw (1) Disconnect wiring connector coming from the fan unit. Connector (2) Remove 5 screws from the fan unit. Sliding Bracket Fan unit (3) There are three screws holding the sliding bracket (right side);...
- Page 12 INSTALLATION (continued) Place the range hood in an upright position and attach the exhaust Exhaust pipe unit pipe unit using the 4 (M4×8) Tape attachment screws provided. Once the exhaust pipe unit is securely attached, remove the tape. Align 4 screw holes Nut with plate Nut with plate of the liner and...
- Page 13 INSTALLATION (continued) Hook the temporary fixing holes of the hanging Duct bracket on the washer-head wood screws prepared in step 8, and tighten the screws. Note Insert tight the exhaust pipe unit into the duct. Add 2 screws (M5.1×45) to the holes under the temporary fixing holes and tighten them securely.
-
Page 14: Mounting Procedure For Buf-07P (Ceiling Mounting)
INSTALLATION (continued) Mounting procedure for BUF-07P (Ceiling Mounting) Put 4 all thread rods (∅1/2'' anchor bolt, not supplied) into the corner holes Mounting bracket of the mounting bracket, and secure them using washers, spring washers, and nuts. Place the mounting bracket on the beam of the ceiling as shown. - Page 15 INSTALLATION (continued) Sound-absorbing box (rear) (2) Remove the two screws holding the rear sound-absorbing box, pull the tab at the top of the box out of the slit, and remove the box. (3) Remove the two screws holding Sound-absorbing box the sound-absorbing box on (left side) each side, pull the tab at the top...
- Page 16 INSTALLATION (continued) (4) Move the fan unit forward to free it from the fixed bracket ➀ (rear) ( (5) Lift the right side of the fan unit ➁ (sliding bracket side) ( (6) Move the fan unit to the right to release it from the fixed bracket ➂...
- Page 17 INSTALLATION (continued) Align 4 screw holes of the liner and Nut with plate [Right & left, each two (2) places] range hood, then Nut with plate fix securely using the supplied screws (M5×30) and nuts. Securing plate Liner [Securing plate Note turns while Fasten all the screws...
-
Page 18: Connecting Power Supply Wires
INSTALLATION (continued) 3. Connecting Power Supply Wires WARNING • Electrical wiring should be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. An unqualified person doing the work could result in fire, electric shock or injury. •... -
Page 19: Final Assembly And Check
INSTALLATION (continued) Screw Slide the wire cover on and insert the hook. Secure the wire cover with the screw removed previously. Make sure that all wires are connected properly and enclosed inside the wiring compartment. Wire cover Hook 4. Final Assembly and Check Attach the fan unit. - Page 20 INSTALLATION (continued) While holding the fan unit, Screw firmly attach it to the main unit using 5 screws. CAUTION Fan unit • Check that the fan unit is hanged securely when attaching. It may cause injury if dropped. Connect the fan unit’s wiring connector. Note Be sure to connect firmly as illustrated.
- Page 21 INSTALLATION (continued) (2) In a similar manner as with the side boxes, insert the tab at the top part of the rear sound- absorbing box into the slit and secure in place by affixing the two screws at the bottom of the box.
-
Page 22: Explanation To The End User By Installer
INSTALLATION (continued) Two 50 Watt halogen light bulbs (not supplied) can be mounted in this range hood. Prior to function check, install light bulbs (PAR20 bulb, with base diameter 26 mm: medium base), rated at 120 V - 50 Watt or below. The following light bulbs are recommended for this range hood.
Need help?
Do you have a question about the BUF-07W and is the answer not in the manual?
Questions and answers