Fujioh BUF-06W Installation Manual

1U03 1383
Model: BUF-06W

SAFETY INSTRUCTIONS

Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.
WARNING:
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION:
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
CAUTION:
CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.
NOTE: The safety instructions are explained with the following
pictographic symbols.
means prohibition. It indicates actions, if any,
that mustn't be done.
means forcible execution. It indicates actions, if
any, that must be done.
WARNING
1. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
2. To reduce the risk of fire or electric shock, do not
use this product with any solid-state speed control
device.
3. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Installation work and electrical wiring must be
done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-
rated construction.

1. Preparation

WARNING:
• If the range hood is not installed properly, it could become detached
and fall.
• Ensure that the metal duct does not touch other metal housing
materials, otherwise fire or electric shock could result.
1 Roof cap
According to the conditions where the
7" round duct
(For vertical
range hood is installed, determine
discharge)
whether it will be discharged vertically
or horizontally (7" round duct). For
vertical or horizontal discharge, run
duct work between the hood location
Soffit
and the roof cap or wall cap.
For best result in either direction, use
a minimum number of transitions and
elbows. Be sure to attach a roof cap

Range hood

or wall cap to avoid rain/wind entry.
2 Liner Dimensions (Unit: inch)
The range hood unit
must be mounted to a
4-∅1/4" Holes for
liner which has the
mounting range hood
following dimensions.
Install the liner securely
after checking that the
Center line
opening size of the liner
is the same as the
Range hood cutout
figure right.
25-3/16"
CAUTION:
26"
• The liner shape illustrated in this installation manual is only for
reference.
CAUTION:
• When the liner is installed in the wooden hood, the inside of the
wooden hood placed above the cooking surface must be fully
covered by the metal barrier including bottom edges. Select a
suitable liner and metal barrier according to the size and shape of
the wooden hood and install properly.
• The liner should be installed tightly. If the liner installation is not
correct, the range hood unit may become detached and fall.
3/4" thickness
3
Make sure that a 3/4" thickness
wood panel is required
wood panel for mounting the range
hood is fixed on the wall where the
Fan unit
range hood is installed.
Note: If no wood panel is found on
the wall, be sure to prepare
Liner
one referring to the figure.
4
Referring to "DIMENSIONS" above, insert 2 1/4"
supplied wood screws into the mounting wall for
the left and right hangers. Allow about 1/4" space
between the wall and screw-heads for hanging.

2. Range Hood Mounting

CAUTION:
• Wear working gloves to avoid injury.
Screw
1
Detach the tape on
Filter
Front Cover
the exhaust port.
2
Detach the filters by
loosening 2 screws.
Remove 5 screws
Loosen 2 screws
fixing the front
to remove the filter.
cover and detach
the front cover.
Cardboard
(Do not remove yet.)
CAUTION:
Do not remove the switch's protective
Detach
cardboard until proceeding to "4. Final
the tape.
Assembly and Check".
Range Hood

INSTALLATION MANUAL

b) Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer's
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and The American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
c) When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
d) Ducted fans must always be vented to the
outdoors.
e) This unit is designed for ducted or ductless
installation. When ductless kit part numbers
FDK-06A is installed, this unit is certified ductless.
The end user is responsible to ensure compliance
with all Federal, State and Local Environmental
and Fire codes.
4. TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
5. This unit must be grounded.
6. Install this range hood to a liner. Check that the
hood is correctly installed, since incorrect
installation could result in the range hood
becoming detached and falling off.
7. Connect only to an AC120 Volt power source or
the range hood could result in fire, electric shock,
and damage.
CAUTION
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive material and
vapors.
2. To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls or ceilings or into attics,
crawl spaces, or garages.
3. Read specification label on this product for further
information and requirements.
4. Use only for the purpose of kitchen ventilation.
5. Do not install this range hood in the bathroom or
in other wet rooms since electrical shock and
damage may result.
6. Fasten the filter and other parts securely. Incorrect
attachment may result in personal injury or
property damage.
7. Keep your hands and other objects away from
the fan while it is in motion. The range hood may
injure you or damage itself.
3
Remove the fan unit from the range hood.
(1) Unplug the connector coming from the fan motor.
(2) Remove 3 screws, then detach the fan unit with sliding it
laterally to disengage from 4 hooks.
(3) Pull up the fan unit while avoiding the bracket.
Screw
Hook
Hook
( 2)
Wall cap
7" round duct
(For horizontal
discharge)
Wire-clamp
Bracket
Front Liner
Connector
( 1)
( 3)
4
Hold up the range hood and align the 4 screw holes of the liner
and range hood, then fix securely using the supplied screws
(M5×30) and nuts.
Note: Fasten all the screws and nuts evenly.
Liner
Securing plate
[Securing plate turns
while passing through
the opening of Liner]
Wall
Four screws (M5×30)
5
With inserting the exhaust
Hanger
port into the duct, hook both
the left and right hangers on
the screws provided in
"Preparation" step 4.
6
Tighten both the left and
Tighten screws to fix
right screws, and fix the
range hood securely
adding 4 more supplied
washer head wood
screws to the holes on
the hangers and back of
the range hood.
7 Make the duct joint secure and
air-tight using non-flammable
tape such as duct tape, etc.
(Not supplied)
Tape
Non-flammable tape
NAMES OF PARTS
Lamp Switch
Fan Switch
Filter

DIMENSIONS

∅
7/8"
8-9/16"
26"
∅
4- 1/4" Holes for
mounting range hood
16-3/8"
25-1/16"
19-13/16"
26-3/4"
16-5/8"
27"

INSTALLATION

3. Connecting Power Supply Wires

WARNING:
• Electrical wiring should be done by a qualified person(s) in
accordance with all applicable codes and standards, including
fire-rated construction. An unqualified person doing the work could
result in fire, electric shock or injury.
• This range hood uses 120V AC. Do not connect to other voltage
since fire, electric shock or damage could result.
Fan Unit
1
Remove the nut from the conduit
connector at the end of power wiring.
WARNING:
Be sure to switch power OFF at service panel before wiring.
Bracket
2
Remove one screw fixing the
wire cover and detach it.
Motor
3
Connect the conduit through the connecting
hole of the body using the nut previously
removed.
Conduit
Screw-washer
[Right & left,
each two (2) places]
4
Connect wires tightly and
Liner
securely using wire
connectors (not supplied).
Connect the electrical
wires as follows:
• Black to Black
• White to White
• Green to Green
5
Replace the wire cover with
the screw removed previously.
Make sure that all wires are
connected properly and
enclosed inside of the wiring
compartment.

4. Final Assembly and Check

Assembly
1
Attach the fan unit while avoiding the bracket, and fix it
using 3 screws.
Bracket

CIRCUIT DIAGRAM

Front Cover
Enclosure
White
120V
Black
60Hz
Green
Black
Capacitor
(Unit: inch)

RANGE HOOD LOCATION

11"
14-5/8" or 16-1/8"
6-5/16"
∅
6-15/16"
1
The range hood must be
installed just above the
cooktop.
19-11/16"
2
The minimum distance
from the cooking surface
to the bottom of the range
hood must be 24".
3
The total weight of the
BUF-06W range hood
unit is 35.2 lbs. (16 kg)
4
Power requirements are:
AC120 V, 60 Hz, 3.0 Amp
WARNING:
• Check that the hood is correctly installed, since incorrect
installation could result in the detachment of the range
hood and the unit could fall.
CAUTION:
• To protect hands from injury, wear working gloves when
installing the range hood.
2
Connect the motor wire connector, and secure it with 2 wire-
clamps.
Connector
Conduit
Wire-clamp
(Not supplied)
3
Remove the switch's protective cardboard.
Nut
(Not supplied)
WARNING:
Remove the protective
cardboard without fail,
otherwise there is a risk
of fire.
Cardboard
Wire cover
4
Screw Attach the front cover,
and secure it with 5 screws.
Then attach the filters.
5
Two 50 Watt halogen light bulbs (not supplied) can be mounted
in this range hood.
Prior to function check, install light bulbs (PAR20 bulb, with base
diameter 26 mm: medium base), rated 120 V - 50 Watt or below.
The following light bulbs are recommended for this range hood.
• GE Model No. 50PAR20H/FL25
• SYLVANIA Model No. 50PAR20/HAL/DL/NFL
Nut
Turn the lamps clock-wise
to install them.
(Not supplied)
Wire connector
(Not supplied)
Check
1
Turn on the electrical circuit to the range hood.
2
Make sure that the switches and light operate correctly.
Refer to page 4 of the Operation Manual.
3
Make sure that the range hood functions properly and it has no
abnormal noises and/or vibration.
Wire cover
Screw

5. Explanation to the End User

Motor
(1) Referring to the Operation Manual, explain the operation of this
range hood to end users.
(2) The Installation Manual and Operation Manual should be given to
the end user.
Lamp Switch Fan Switch
Connector
Pilot Lamp
Connector
Black White
Grey Yellow
Black
Lamp
Motor Yellow Yellow
White
White
Black
Black
Connector
Connector
Connector
White White
Black
Black
Connector Lamp
White
ACCESSORIES
Screw M5.1×45
Four (4) pieces
Screw M4.5×45
Two (2) pieces
Screw M5×30
Four (4) pieces
Nut with plate
Four (4) pieces
Liner
24" (Minimum)
Cook top
Screw
Fan
Hook
Unit
Hook
Bracket
Hook
Screw
Filter
Bulb
Push to turn ON