Fujioh BUF-06P Installation Manual

1U03 1483
Model: BUF-06P

SAFETY INSTRUCTIONS

Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.
WARNING:
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION:
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
CAUTION:
CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.
NOTE: The safety instructions are explained with the following
pictographic symbols.
means prohibition. It indicates actions, if any, that
mustn't be done.
means forcible execution. It indicates actions, if
any, that must be done.
WARNING
1. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
2. To reduce the risk of fire or electric shock, do not
use this product with any solid-state speed control
device.
3. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Installation work and electrical wiring must be
done by a qualified person(s) in accordance with
all applicable codes and standards, including fire-
rated construction.
1. Preparation
The following method is the standard installation.
There may be some different cases depending on the structure of
the ceiling where the mounting bracket is placed or the shape and
mounting condition of the wood hood.
In such a case, please arrange best possible way according to the
condition of the place where the range hood is being installed.
WARNING:
• If the range hood is not installed properly, it could become detached and
fall.
• Ensure that the metal duct does not touch other metal housing materials,
otherwise fire or electric shock could result.
Roof cap
1
According to the conditions where
7" round duct
the range hood is installed,
(For vertical discharge)
determine whether it will be
discharged vertically or
horizontally (7" round duct). For
vertical or horizontal discharge,
run duct work between the hood
location and the roof cap or wall
cap.
For best result in either direction,
Soffit
use a minimum number of
transitions and elbows. Be sure to
Wood
attach a roof cap or wall cap to
hood

Range hood

avoid rain/wind entry.
2
The range hood unit must
Liner Dimensions (Unit: inch)
be mounted to a liner
4-∅1/4"
which has the following
Holes for mounting
dimensions. Install the
range hood
Center line
liner securely after
checking that the opening
size of the liner is the
Range hood cutout
same as the figure right.
25-3/16"
26"
CAUTION:
• The liner shape illustrated in this installation manual is only for reference.
CAUTION:
• When the liner is installed in the wooden hood, the inside of the wooden
hood placed above the cooking surface must be fully covered by the metal
barrier including bottom edges. Select a suitable liner and metal barrier
according to the size and shape of the wooden hood and install properly.
• The liner should be installed tightly. If the liner installation is not correct,
the range hood unit may become detached and fall.
3
Put 4 all thread rod (∅1/2" anchor bolt, not supplied) into the corner
holes of the mounting bracket, and secure them using washers, spring
washers, and nuts. Place the mounting bracket on the beam of the
ceiling as shown.
Mounting Bracket
Note: The mounting bracket
should be securely
fastened at this point
to simplify installing
the range hood later.
Nut*
Spring-washer*
Washer*
Bracket
* Not supplied

2. Range Hood Mounting

CAUTION:
• Wear working gloves to avoid injury.
1 Screw
Detach the tape on
Filter
the exhaust port.
2
Detach the filters by
loosening 2 screws.
Then remove 5
Loosen 2 screws
screws holding the
to remove the filter.
front cover and
detach the front cover.
Cardboard
(Do not remove yet.)
CAUTION:
Tape
Do not remove the switch's protective
Detach
cardboard until proceeding to "4. Final
the tape.
Assembly and Check".

INSTALLATION MANUAL

b) Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney)
of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer's
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and The American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
c) When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
d) Ducted fans must always be vented to the
outdoors.
e) This unit is designed for ducted or ductless
installation. When ductless kit part numbers
FDK-06A is installed, this unit is certified ductless.
The end user is responsible to ensure compliance
with all Federal, State and Local Environmental
and Fire codes.
4. TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
5. This unit must be grounded.
6. Install this range hood to a liner. Check that the
hood is correctly installed, since incorrect
installation could result in the range hood
becoming detached and falling off.
7. Connect only to an AC120 Volt power source or
the range hood could result in fire, electric shock,
and damage.
CAUTION
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive material and
vapors.
2. To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls or ceilings or into attics,
crawl spaces, or garages.
3. Read specification label on this product for further
information and requirements.
4. Use only for the purpose of kitchen ventilation.
5. Do not install this range hood in the bathroom or
in other wet rooms since electrical shock and
damage may result.
6. Fasten the filter and other parts securely. Incorrect
attachment may result in personal injury or
property damage.
7. Keep your hands and other objects away from
the fan while it is in motion. The range hood may
injure you or damage itself.
3
Remove the fan unit from the range hood.
(1) Unplug the connector coming from the fan motor.
(2) Remove 3 screws, then detach the fan unit with sliding it laterally
to disengage from 4 hooks.
(3) Pull up the fan unit while avoiding the bracket.
Screw
Hook
(2)
Wire-clamp
Bracket
Wall cap
Connector
7" round duct
(For holizontal
discharge)
Front Liner (1)
(3)
4
Hold up the range hood,
and with inserting the
exhaust port into the duct,
pass all 4 threaded rods
through the corner holes
of the range hood.
5
Align 4 screw holes of the liner and range hood, then fix securely
using the supplied screws (M5×30) and nuts.
Note: Fasten all the screws and nuts evenly.
Liner
Securing plate
Beam
[Securing plate turns
while passing through
the opening of Liner]
Four screws (M5×30)
6
Using washers, spring washers, and double nuts, attach the range
hood to all 4 threaded rods securely.
*
Not supplied
Front Cover
Washer*
Spring-washer*
Nut*
7
Make the duct joint secure and air-tight using non-flammable tape such
as duct tape, etc. (Not supplied)
Non-flammable tape
Range Hood
NAMES OF PARTS
Control Switches
Filter
Pilot Lamp
OFF Switch
Low Switch
DIMENSIONS
17-13/16"
8-9/16"
∅
4- 1/4"
26"
Holes for mounting range hood
∅
7/8"
15-13/16"
25-1/16"
10-3/8"
19-7/8"
26-3/4" 16-5/8"
27"
INSTALLATION
Note: If taping from the outside is impossible, remove the exhaust port
and insert the duct end to the range hood directly, then make
inside taping on the duct end. Be sure to attach a duct cover with
damper in this case.
Hook
Exhaust port
Fan Unit

3. Connecting Power Supply Wires

WARNING:
• Electrical wiring should be done by a qualified person(s) in accordance
with all applicable codes and standards, including fire-rated construction.
An unqualified person doing the work could result in fire, electric shock
Bracket
or injury.
• This range hood uses 120V AC. Do not connect to other voltage since
fire, electric shock or damage could result.
1
Remove the nut from the conduit
connector at the end of power wiring.
WARNING:
Be sure to switch power OFF
Motor at service panel before wiring.
2
Remove one screw fixing the
wire cover and detach it.
3
Connect the conduit
through the connecting
hole of the body using
the nut previously
removed.
4
Connect wires tightly and
securely using wire
connectors (not supplied).
Connect the electrical wires
Screw-washer
as follows:
[Right & left,
each two (2) places]
• Black to Black
• White to White
• Green to Green
5
Replace the wire cover with the
Liner
screw removed previously. Make
sure that all wires are connected
properly and enclosed inside of
the wiring compartment.

4. Final Assembly and Check

Assembly
1 Attach the fan unit while avoiding the bracket, and fix it using 3 screws.

CIRCUIT DIAGRAM

Front Cover
Enclosure
White
120V
Black
60Hz
Green
Black
Lamp Switch
High Switch
Medium Switch Capacitor
(Unit: inch)

RANGE HOOD LOCATION

1
The range hood must be installed
∅
6-15/16"
just above the cooktop.
2
The minimum distance from the
cooking surface to the bottom of
the range hood must be 24".
3
The total weight of the BUF-06P
range hood unit is 37.4 lbs. (17 kg)
4
Power requirements are:
AC120 V, 60 Hz, 3.0 Amp
WARNING:
• Check that the hood is correctly installed, since incorrect installation
could result in the detachment of the range hood and the unit could fall.
CAUTION:
• To protect hands from injury, wear working gloves when installing the
range hood.
2
Connect the motor wire connector, and secure it with the wire-clamp.
Duct Range hood Non-flammable
tape
Duct
Connector
Wire-clamp
3
Remove the switch's protective cardboard.
WARNING:
Remove the protective
cardboard without fail,
otherwise there is a risk
of fire.
Conduit
(Not supplied)
Nut
(Not supplied)
Cardboard
4
Attach the front cover,
and secure it with 5 screws.
Wire cover
Then attach the filters.
Screw
5
Two 50 Watt halogen light bulbs (not supplied) can be mounted in this
range hood.
Prior to function check, install light bulbs (PAR20 bulb, with base
Conduit
diameter 26 mm: medium base), rated 120 V - 50 Watt or below.
The following light bulbs are recommended for this range hood.
• GE Model No. 50PAR20H/FL25
• SYLVANIA Model No. 50PAR20/HAL/DL/NFL
Turn the lamps clock-wise
Nut
to install them.
Bulb
(Not supplied)
Wire connector
(Not supplied)
Check
1
Turn on the electrical circuit to the range hood.
2
Make sure that the switches and light operate correctly.
Refer to page 4 of the Operation Manual.
3
Make sure that the range hood functions properly and it has no
Wire cover
abnormal noises and/or vibration.
Screw
5. Explanation to the End User
Motor
(1) Referring to the Operation Manual, explain the operation of this range
hood to end users.
(2) The Installation Manual and Operation Manual should be given to the
Bracket
end user.
Lamp Switch Fan Switch
Connector
Pilot Lamp
Connector
Black White
Grey Yellow
Black
Lamp
Motor Yellow Yellow
White White
Black
Black
Connector
Connector
Connector
White
White
Black
Black
Lamp
Connector
White
ACCESSORIES
Screw M5×30
Mounting Bracket
Four (4) pieces
One (1) piece
Nut with plate
Four (4) pieces
Liner
24" (Minimum)
Cook top
Screw
Hook
Fan
Unit
Hook
Bracket
Hook
Front cover
Screw
Filter
Push to turn ON