Heat & Glo CERONA-36 Owner's Manual
  1. Manuals
  2. Brands
  3. Heat & Glo Manuals
  4. Indoor Fireplace
  5. CERONA-36
  6. Owner's manual
Heat & Glo CERONA-36 Owner's Manual

Heat & Glo CERONA-36 Owner's Manual

Installation and operation
Hide thumbs Also See for CERONA-36:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
Models:
CERONA-36
CERONA-42
•
Important operating
and maintenance
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing proper-
ty damage, personal injury, or death.
• Do not store or use gasoline or other flamma-
ble vapors and liquids in the vicinity of this or
any other appliance.
• What to do if you smell gas
- Do not try to light any appliance
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed by
a qualified installer, service agency, or the gas
supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must
be installed in accordance with the manufacturer's instruc-
tions and the manufactured home construction and safety
standard, Title 24 CFR, Part 3280 or Standard for Installa-
tion in Mobile Homes, CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indi-
cated on the rating plate.
CAUTION
DO NOT DISCARD THIS MANUAL
•
Read, understand and follow
these instructions for safe
installation and operation.
Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06
Owner's Manual
Installation and Operation
•
Leave this manual with
party responsible for
use and operation.
WARNING
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
Glass and other surfaces are hot during
operation and cool down.
• Keep children away.
• CAREFULLY SUPERVISE children in same room as
appliance.
• Alert children and adults to hazards of high
temperatures.
• Do NOT operate with protective barriers open or
removed.
• Keep clothing, furniture, draperies and other
combustibles away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. Do
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts:
• Installation must be performed by a licensed plumber or
gas fitter;
See Table of Contents for location of additional
Commonwealth of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory-trained
professionals, or technicians supervised
by an NFI certified professional.
1

Advertisement

Table of Contents
loading

Related Manuals for Heat & Glo CERONA-36

Summary of Contents for Heat & Glo CERONA-36

  • Page 1 Mobile Homes, CAN/CSA Z240MH. professionals, or technicians supervised This appliance is only for use with the type(s) of gas indi- by an NFI certified professional. cated on the rating plate. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 2 IN CANADA Serial Number Model: XXXXXXXX ALTITUDE: 0-0000 FT. 0000-0000FT. (Modele): MAX. INPUT BTUH: 00,000 00,000 MIN. INPUT BTUH: 00,000 00,000 Serial ORIFICE SIZE: #XXXXX #XXXXX XXXXXXXX (Serie): Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 3: Table Of Contents

    A. Assembly of Vent Sections ......23 B. Disassembly of Vent Sections ....25 C. Installing Heat Shield & Termination Cap . 26 D. Installing Roof Flashing and Vertical Termination Cap ......... 27 Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 4: Listing And Code Approvals Section

    (2000-4500 FT) or unplastered shall be considered combustible materials. Heat & Glo Quality Systems registered by SGS ICS Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 5: Requirements For The Commonwealth Of Massachusetts

    See Gas Connection section for additional Common- print size no less than one-half (1/2) inch in size, “GAS wealth of Massachusetts requirements. VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OB- STRUCTIONS”. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 6: Getting Started

    Safety glasses Level 1/2 - 3/4 inch length, #6 or #8 Self-drilling screws Manometer Voltmeter Tape measure Noncorrosive leak check solution One 1/4 inch female connection (for optional fan). Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 7: Framing And Clearances A. Selecting Appliance Location

    • Vent Clearances and Framing (Section 6). CERONA-36 42-1/8 73-1/4 65-1/2 22-1/4 Inches 1295 1070 1861 1664 Millimeters CERONA-42 56-5/8 49-1/8 80-1/8 72-1/2 22-1/4 Inches 1438 1248 2035 1842 Millimeters Figure 3.1 Appliance Locations Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 8: Constructing The Appliance Chase

    (Vent Pipe) (Height) (Depth) (Width) of Arch Opening 50-1/2 22-1/4 42-1/8 Cerona-36 1283 1070 1245 54-1/2 22-1/4 49-1/8 45-1/4 Cerona-42 1384 1248 1149 Figure 3.2 Clearances to Combustibles Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 9: Mantel Projections

    11 12 ∞ 25 51 76 102 127 152 178 203 229 254 279 Figure 3.4 Clearances to Mantel Legs or Wall Projections (Acceptable on both sides of opening.) Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 10: Hearth Extension

    (6 inch Minimum to top surface of combustible in. 41-1/8 Cerona-36 floor or floor covering. mm 1045 203 Figure 3.8 in. 48-1/8 Cerona-42 mm 1222 203 Figure 3.6 Hearth Extension Dimensions Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 11: Termination Locations

    OIL TERMINATION 20 IN. (MINIMUM) TO PERPENDICULAR WALL (GAS ONLY) TERMINATION 18 IN. Gas Termination Wood & Fuel Oil Termination 6 in. 20 in. Figure 4.3 Multiple Vertical Termination Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 12 Figure 4.4 Minimum Clearances for Termination CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 13: Continue Adding Vent Components

    (2) the shield and the combustible surface. See Figure 4.6. sheet metal screws. C. Install Support Brackets Refer to Cinch Pipe and Termination Cap installation in- structions. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 14: Vent Information And Diagrams

    (see Figure 5.1). DVP12A 3 to 12 76 to 305 DVP12MI 3 to 12 76 to 305 DVP24MI 3 to 24 76 to 610 Figure 5.2 DVP Pipe Effective Length Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 15: Vent Diagrams

    NOTE: Must have HORIZONTALLY Minimal Vertical Vent a minimum verti- Model cal vent before at- taching a 90 Cerona-36 0.5 bow to the unit. Cerona-42 See chart. Figure 5.4 Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 16 Straight Up Vertical Venting NOTE: On vertical venting config- urations install the flue restrictor found in the appliance manual bag. Follow flue restrictor instructions in Section 7D. Figure 5.6 Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 17 = 62 ft (18.9 m) Max. Minimal Vertical Vent Model Cerona-36 0.5 Cerona-42 NOTE: Must have a minimum INSTALLED HORIZONTALLY vertical vent before attaching a elbow to the unit. See chart. Figure 5.8 Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 18: Vent Clearances And Framing

    1 in. CLEARANCE WALL BOTTOM & SIDES inch greater than the pipe is acceptable. SHIELD FIRESTOP WALL Figure 6.2 Horizontal Venting Clearances to Combustible Materials Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 19: Vertical Penetration Framing

    • Field construct additional shield height if insulation is deeper than height of at- ATTIC SHIELD INSTALLED ATTIC SHIELD INSTALLED tic shield. ABOVE CEILING BELOW CEILING Figure 6.4 Installing the Attic Shield Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 20: Appliance Preparation

    • Replace screws in holes where these pieces were at- Remove screws from upper tached to appliance. bracket. L o w e r Bracket Figure 7.1 Non-Combustible Facing Material Assembly Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 21: Securing And Leveling The Appliance

    • Keep nailing tabs flush with the framing. • Secure the appliance to the framing by using nails or screws Figure 7.3 Attaching Non-combustible Facing Material through the nailing tabs. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 22: Installing Flue Restrictors

    • Use a wet or dry towel or soft brush to remove dust or dirt from facing material. • Apply a non-combustible adhesive to attach tile, stone or other non-combustible finishing materials per manufacturer’s instructions. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 23: Installing Vent Pipe

    Once both inner and outer flues are started, press section A onto predrilling screw holes, do NOT penetrate inner pipe. section B firmly until all lances have snapped into place. Check to Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 24 If the slip section is too long, the inner and outer flues of the slip section can be cut to the desired length. Figure 8.8 Screws into Slip Section Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 25: Disassembly Of Vent Sections

    • Do NOT allow vent to sag below connection point to appliance. Improper support may allow vent to sag or separate. Figure 8.12 Align and Disassemble Vent Sections Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 26 (pipe section) to properly space it from the available. pipe section (see Figure 8.13). When penetrating a brick wall, a brick extension kit is available for framing the brick. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 27: Installing Roof Flashing And Vertical Termination Cap

    Fire Risk. Explosion Risk. Inspect external vent cap regularly. • Ensure no debris blocks cap. • Combustible materials blocking cap may ignite. • Restricted air flow affects burner operation. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 28 Slide the assembled storm collar down the pipe section until it rests on the roof flashing. Caulk around the top of the storm collar (see Figure 8.15). Figure 8.16 Assembling the Storm Collar Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 29: Gas Information

    Propane Minimum 5.0 inches 11.0 inches Inlet Pressure w.c. w.c. Maximum Inlet 14.0 inches 14.0 inches Gas Pressure w.c. w.c. Manifold 3.5 inches 10.0 inches Pressure w.c. w.c. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 30 Fire hazard. Do NOT change the valve settings. • This valve has been preset at the factory. • Changing valve settings may result in fire hazard or bodily injury. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 31: Electrical Information

    • Replace damaged wire with type 105 rated wire. • Low voltage and 110 VAC voltage cannot be shared within the same wall box. • Wire must have high temperature insulation. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 32 DEXEN IPI VALVE GROUND CONNECTED YEL/WHT CONTROL MODULE J-BOX (110V) HI/LO HI/LO SOLENOID NOTE: WIRE TYPE 80°C Note: Appliance will not operate unless properly grounded. Figure 10.1 IPI Wiring Diagram Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 33: Junction Box Installation

    • Pull the electrical wires from outside the appliance through this opening into the valve compartment. • Make all necessary wire connections to the receptacle and assemble the receptacle and cover to the junction box. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 34: Finishing

    Seal joints between the finished wall and appliance Figure 11.2 Mantel Leg or Wall Projections top and sides using only a high temperature sealant (Acceptable on both sides of opening.) or stove cement. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 35: Finishing Material Requirements

    Failure to do so will result in the front not fitting (see Figure 11.5). Figure 11.4 Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 36: Hearth Extension

    Figure 11.6 Position of board and template NAILING TABS (BOTH SIDES) in. 41-1/8 Cerona-36 mm 1045 203 in. 48-1/8 Cerona-42 mm 1222 203 Figure 11.7 Hearth Extension Dimensions Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 37: Appliance Setup

    • Save the remaining ember materials for use during appli- • Only Hearth & Home Technologies ance servicing. The embers provided should be enough approved accessories may be used safely. for 3 to 5 applications. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 38: Positioning The Logs

    It may be necessary to tilt Log #1 formed portion of log #2. 2106-935 forward to properly engage with Log #2. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 39 Figure 12.11 STEP 7. LOG #6 (SRV2106-706): Rest bottom notch of log #6 on the grate tine and the top part on formed section of log #5 (A). Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 40 Rest the top of the log on the flat section of log #1. See Figure 12.15 FORM FITTED TO GRATE TINE Figure 12.15 2107-935 Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 41 LOG #5 (SRV2107-705): Place log #5 on the left side between the grate tine and firebox. Note: This log will be used to support log #6. Figure 12.18 Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 42: Glass Assembly

    Marble, brass, brick, tile, or other noncombustible BOTTOM OF FIREPLACE WITH BOTTOM TRAY REMOVED materials can be used to cover up the gap between the Figure 12.20 sheet rock and the appliance. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 43: Operating Instructions

    • Glass door MUST be in place and sealed before operating appliance. • Only use glass door certified for use with appliance. • Glass replacement should be done by qualified technician. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 44: Lighting Appliance

    For additional information on operating your Hearth Technologies appliance, please refer to www.Fireplaces.com. 2095-913B Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 45: After Appliance Is Lit

    In an Intellifire ignition system it is normal to see the pilot flame, but it should turn off burn continually? when ON/OFF is turned off. In a standing pilot system the pilot will always stay on. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 46: Troubleshooting

    The sensor rod may be contaminated. Clean sensor rod with emery cloth. c. Module is not Verify that module is securely grounded to metal chassis of appliance. Verify grounded. that wire harness is firmly connected to module. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 47 Verify module is securely grounded to metal chassis of appliance. grounded. d. Module voltage Verify battery voltage is at least 2.7 volts. Replace batteries if voltage is output / Valve/Pilot below 2.7. solenoid ohms readings. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 48: Maintaining And Servicing Appliance

    • Restricted air flow affects burner operation. control compartment • Burner, burner ports Risk of: • Fire • Delayed ignition or explosion • Exposure to combustion fumes • Odors Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 49 4. Inspect for corrosion or separation. 5. Verify weather stripping, sealing and flashing remains intact. 6. Inspect draft shield to verify it is not bent, damaged or missing. Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 50: Reference Materials

    1046 27-3/4 48-1/8 1223 30-1/4 21-3/4 35-7/8 21-3/4 33-7/8 28-1/2 39-1/2 1005 35-3/8 6-5/8 14-1/4 6-3/4 17-3/4 34-1/2 12-1/2 38-5/8 12-5/8 49-7/8 1268 1372 Figure 16.1 Appliance Dimensions Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 51: Vent Components Diagrams

    14 in. (356 mm) 5 in. 12 in. (127 mm) (305 mm) 6 in. (152 mm) DVP-HVS (Vent Support) DVP-WS (Wall Shield Firestop) Figure 16.2 DVP vent components Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 52 INCHES TRAP1 4-1/8 5-5/8 TRAP2 6-3/4 10-5/8 14 in. DVP-TRAP (566 mm) Horizontal Term Cap DVP-TRAP1 DVP-TRAPK1 DVP-TRAP2 DVP-TRAPK2 DVP-HPC1 DVP-HPCK1-B DVP-HPC2 DVP-HPCK2-B Figure 16.3 DVP vent components Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 53 5-3/4 in. (146 mm) COOL-ADD Cap Shield 13-7/8 in. 9-1/2 in. (352 mm) (241 mm) 14 in. (356 mm) DVP-TRAPFL DRC-RADIUS Flashing Cap Shield Figure 16.4 DVP vent components Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 54 (222 mm) 7-3/4 to 10-3/8 in. (197 to 264 mm) 1-5/8 in. (41 mm) DVP-FBHT Fire Brick Termination Cap DVP-HPC High Performance Cap Figure 16.5 DVP vent components Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 55: Service Parts

    CERONA-36 C. Service Parts Beginning Manufacturing Date: 6-06 (NG, LP) Exploded Parts Diagram Ending Manufacturing Date: ______ Cerona-36 Log Set Assembly Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 56 Template - For finishing materials greater than 1-1/4 inch CERONA36-TMPLT Touch Up Paint - Black TUP-GBK-12 Box Touch up Kit CERONA-PAINT Heat Duct Kit Heat-Duct Wall Switch Kit WSK300-HNG Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 57 CERONA-42 C. Service Parts Beginning Manufacturing Date: 6-06 (NG, LP) Exploded Parts Diagram Ending Manufacturing Date: ______ Cerona-42 Log Set Assembly Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 58 Fiber Patch Kit SRV-PACK Template - For finishing materials greater than 1-1/4 inch CERONA42-TMPLT Touch Up Paint - Black TUP-GBK-12 Box Paint Kit CERONA-PAINT Heat Duct Kit Heat-Duct Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 59 Burner Orifice NG (#32C) 582-832 Burner Orifice LP (#50C) 582-850 Shutter Sleeve 2026-130 Battery Pack 593-594A Pilot Spud, LP 593-527 Pilot Spud, NG 593-528 Regulator, LP LPK-DXV Regulator, NG NGK-DXV Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...
  • Page 60 2026-130 B attery P ack 593-594A P ilot Spud, LP 593-527 P ilot Spud, NG 593-528 Regulator, LP LP K-D X V Regulator, NG NGK -D X V Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 61: Warranty

    3. HEAT & GLO reserves the right to make changes at any time, without notice, in design, material, specifications and prices of the Product. HEAT & GLO also reserves the right to discontinue styles and products. © 2005 Hearth & Home Technologies Inc. 060-981D 3/05 Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

  • Page 62: Contact Information

    6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending. Printed in U.S.A. - Copyright 2006 Heat & Glo • Cerona-36, Cerona-42 • 2106-900 Rev. A • 6/06...

This manual is also suitable for:

Cerona-42

Table of Contents