Advertisement
Advertisement
Table of Contents
Related Manuals for Thermaltake Lanbox Lite VF6000BWS
Summary of Contents for Thermaltake Lanbox Lite VF6000BWS
- Page 1 VF6000 Series 2006 Thermaltake Technology Co., Ltd. All Rights Reserved. 2006.12 All other registered trademarks belong to their respective companies. www.thermaltake.com Tested To Comply With FCC Standards FOR HOME OR OFFICE USE...
-
Page 2: Chapter 1. Product Introduction
Chapter 1. Product Introduction Specification VF6000BWS VF6000BNS hapter 1. Product Introduction Model Specification hapter 2. Case Mechanical Operation How to open the top panel 5.25" device installation Case Type Gaming Cube 2-2-1 CD-ROM installation 300 x 430 x 230 mm Dimension (W*D*H) 2-2-2 5.25"... -
Page 3: Chapter 2. Case Mechanical Operation
Chapter 2. Case Mechanical Operation How to open the top panel 5.25" device installation 2-2-1 CD-ROM installation Unscrew the 3 screws shown to open the top panel. Unscrew the 2 screws as shown to slide back the optical drive tray. Pull back the top panel as shown to loosen the panel. - Page 4 Screw in the optical drive on the opposing side. Secure the optical drive on the opposing side of No.4 hole as well. When installing an optical drive on the top bay, please install the metal adaptor first as shown. Secure the top optical drive bay as shown.
- Page 5 2-2-2 5.25" accessory drive installation Remove the 5.25" bay cover as arrow shows. There are five springs in the front panel, push to release it. When installing a 5.25" accessory drive on the top bay, please install the metal adaptor first as shown. Screw in the 5.25"...
-
Page 6: Hdd Installation
HDD installation 2-3-1 Install HDD on the HDD rack 2-3-2 Install HDD on the side of optical drive tray Unscrew the screw shown to remove the HDD rack. Unscrew the 2 screws as shown to slide back the optical drive tray. Slide over the HDD rack The HDD rack. -
Page 7: Installing Power Supply
Installing 3.5" device Installing power supply Unscrew the 6 screws Lift out the power supply If a floppy drive is to be holding in the top power tray as shown. installed, please remove supply tray. the bay cover first. The power supply tray. Secure the floppy drive using screws then screw the opposing side as shown. - Page 8 Installing coolant tubes Installing graphics and PCI expansion cards Please install the rubber If a liquid cooling system is to be installed, please tube protector as shown. pry off the top tab of the motherboard tray as shown. Remove the screw as shown to install graphics and PCI expansion cards.
-
Page 9: Motherboard Installation
Chapter3 Motherboard & Leads Installation How to open the front panel Motherboard Installation Each motherboard has different standoff layout. It is highly suggested that you refer to your motherboard's manual when installing motherboard into the Case. The cases are applicable with Standard Micro ATX and mini ITX motherboards. -
Page 10: Case Led Connections
Case LED connections USB 2.0 & IEEE 1394 Firewire Connection USB connection On the front of the case, you can find some LEDs and switch leads (POWER SW*1, POWER LED*1, H.D.D. LED*1, RESET SW*1) Please consult your motherboard manual to find Please consult user manual of your motherboard manufacturer, then out the section of "USB connection". -
Page 11: Audio Connection
Audio Connection Please check your motherboard ,does it support AC'97 IEEE1394 Firewire connection or HD-Audio(AZALIA) , choose one of them to connect. Please consult your motherboard manual to find HD AUDIO(AZALIA) out the section of "IEEE1394 Firewire connection". IEEE 1394 Splout L Return L ( Blank ) - Page 12 - Silent Blue LED fan,1700rpm, 17dBA - Universal design for Intel Socket LGA775 & AMD Socket K8. There are recommended products of Thermaltake PSU and Cooler , it is divided into standard, VR and specialty power supply unit. Please refer to http://www.thermaltake.com...