Related Manuals for Thermaltake VC3000SWA
Summary of Contents for Thermaltake VC3000SWA
- Page 1 2005 Thermaltake Technology Co., Ltd. All Rights Reserved. All other registered trademarks belong to their respective companies.
- Page 2 VC3000 Series User's Manual...
-
Page 4: Table Of Contents
Contents ontents hapter 1. Product Introduction Specification hapter 2. Case Mechaniacl Operation How to open the side panel Lock operation 5.25" device installation HDD installation Installing 3.5" device & HDD to drive tray with power button Installing 3.5" device PCI slot tool-free usage BTX Upgrade Kits (optional) hapter3 Motherboard &... - Page 5 3000SNA & 3000SWA VC3000SNA VC3000SWA Model Case Type Middle Tower Transparent Window Side Panel 4.93 kg 5.15 kg Net Weight Dimension 478.0 mm x 210.0 mm x 495.0 mm (H*W*D) Front (intake) : 120x120x25mm blue LED fan, 1300rpm, 17dBA Cooling System...
- Page 6 3000BNS & 3000BWS VC3000BNS VC3000BWS Model Case Type Middle Tower Transparent Window Side Panel 9.75 kg 9.92 kg Net Weight Dimension 478.0 mm x 210.0 mm x 495.0 mm (H*W*D) Front (intake) : 120x120x25mm blue LED fan, 1300rpm, 17dBA Cooling System VC3000BNS Rear (exhaust) : 120x120x25mm, 1300rpm, 17dBA...
-
Page 7: C Hapter 2. Case Mechaniacl Operation
Chapter2 Case Mechanical Operation 2.1 How to open the side panel Make sure the side panel Please find the side panel lock is opened. key in the back of the chassis, and open the side panel as shown below. Unlock Unlock Unlock Push the button then swing... -
Page 8: Lock Operation
2.2 Lock operation Insert the provided key and turn it counterclockwise. Turn it counterclockwise 90 to open the whole front panel. -
Page 9: Device Installation
2.3 5.25" device installation Unscrew and remove the 5.25" cover with mesh and black sponge. - Page 10 Unscrew the 5.25" drive bay metal cover. Find the drive bay rails from the enclosed box. Please note the different between the right(R) & left (L) rails.
- Page 11 Insert the railed device into the 5.25" drive bay then slide it along the fixed-positioning rack inside the 5.25" cage.
-
Page 12: Hdd Installation
2.4 HDD installation Unscrew the HDD cage as shown. Pull the cage out. Insert HDD drive into the cage. - Page 13 Fasten the HDD using the screw. Slide the cage into drive bay then screw up the screw.
-
Page 14: Installing 3.5" Device & Hdd To Drive
2.5 Installing 3.5" device & HDD to drive tray with power button 2.5.1 Install 3.5" device to drive tray with power button. Slide the drive rails out-ward to remove the drive tray. Squeeze both top and bottom portion of drive tra y cov er to r emo ve it . - Page 15 Place cover back to drive tray to its original position. Insert 3.5" device and secure device with screw. Insert the railed device into the 5.25" drive bay then slide it along the fixed-positioning rack inside the 5.25" cage.
- Page 16 2.5.2 Install HDD drive tray with power button. Place and fasten the device by screws. Insert the railed device into the 5.25" drive bay then slide it along the fixed-positioning rack inside the 5.25" cage. Drive tray with Power Button can be placed at any drive bay as desired.
-
Page 17: Installing 3.5" Device
2.6 Installing 3.5" device Remove the mesh and the black sponge from the front panel. After placing 3.5" device, secure the device with screws. -
Page 18: Pci Slot Tool-Free Usage
2.7 PCI slot tool-free usage Release the plastic clip as follow. Take off the PCI bracket. Locate Graphic Card to the motherboard through fixing it on the space of PCI bracket and insert it to the PCI slot. - Page 19 Push back the plastic clip to secure the Graphic Card. Notice: Fix the pin into the hole securely.
-
Page 20: Btx Upgrade Kits (Optional)
2.8 BTX Upgrade Kits (optional) BTX rear plate BTX SRM (Supported Retention Module) -
Page 21: Chapter3 Motherboard & Leads Installation
Chapter3 Motherboard & Leads Installation 3.1 Motherboard Installation Each motherboard has different standoff layout. It is highly suggested that you refer to your motherboard's manual when installing motherboard into the Case. The cases are applicable with Standard ATX and Micro ATX motherboards. Your motherboard may require a special I/O Panel, which should be included with your motherboard. -
Page 22: Case Led Connections
3.2 Case LED connections On the front of the case, you can find some LEDs and switch leads (POWER SW*1, POWER LED*1, H.D.D. LED*1, RESET SW*1) Please consult user manual of your motherboard manufacturer, then connect these leads to the panel header on the motherboard. These leads are usually labeled;... -
Page 23: Usb2.0 & Ieee1394 Firewire Connection
3.3 USB2.0 & IEEE1394 Firewire connection USB connection Please consult your motherboard manual to find out the section of "USB connection". USB2.0 connection Case layout M/B layout (Ex: ASUS) USB+5V VCC 1 White LDM1 DATA-1 Green LDP1 DATA+1 USB 1 GND 1 Black SHIELD 1... - Page 24 IEEE1394 Firewire connection Please consult your motherboard manual to find out the section of "IEEE1394 Firewire connection". 1394 Firewire connection M/B layout (Ex: ASUS) Case layout White +12V Black Ground TPB- or TPB* TPB- TPB+ or TPB TPB+ Green TPA- or TPA* TPA- Orange TPA+...
-
Page 25: Ear & Mic Connections
3.4 Ear & MIC connections Please consult your motherboard manual to find out the section of "front panel audio connector". Ear & Mic connection M/B layout (Ex: ASUS) Case layout LINE_OUT R EAR R LINE_IN R Return R White LINE_OUT L EAR L Green LINE_IN L... -
Page 26: Chapter4 Other
AC Input cycled on/off under high temperature condition. Furthermore, it has been approved by UL, CSA, TUV, VDE, NODIC, CB, FCC, CE, CNS. There are three main products of Thermaltake PSU, it is divided into standard, VR and specialty power supply unit. Please refer to http://www.thermaltake.com/purepower/main.htm...
Need help?
Do you have a question about the VC3000SWA and is the answer not in the manual?
Questions and answers
Cómo conectar el panel frontal
To connect the front panel of the Thermaltake VC3000SWA:
1. Locate the front panel leads: POWER SW, POWER LED, H.D.D. LED, and RESET SW.
2. Refer to your motherboard manual to find the front panel header (panel connector).
3. Connect the leads as follows:
- POWER LED → PLED pins on the motherboard.
- POWER SW → PWR connector on the motherboard.
- H.D.D. LED → HDD LED pins (usually 2-pin).
- RESET SW → RESET connector on the motherboard.
4. Match the pin labels and orientation as shown in your motherboard manual.
This answer is automatically generated