Hoshizaki F-330BAH(-C) Instruction Manual
Self-contained flaker
Hide thumbs
Also See for F-330BAH(-C):
- Specifications (2 pages) ,
- Service manual (49 pages) ,
- Parts list (23 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Service Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hoshizaki F-330BAH(-C)
Summary of Contents for Hoshizaki F-330BAH(-C)
- Page 1 Hoshizaki America, Inc. “A Superior Degree of Reliability” www.hoshizaki.com Self-Contained Flaker Model F-330BAH(-C) INSTRUCTION MANUAL ® Issued: 5-4-2007 Revised: 9-5-2007...
- Page 2 Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, write, or send an e-mail message to the HOSHIZAKI Technical Support Department for assistance. HOSHIZAKI AMERICA, INC.
-
Page 3: Table Of Contents
• Please review this manual. It should be read carefully before the icemaker is installed and operated. Only qualified service technicians should install, service, and maintain the icemaker. This manual should be made available to the technician prior to installation, maintenance, or service. • Keep this manual with the icemaker for later reference. I. Specifications ... 4 A. Nameplate Rating ... 4 B. -
Page 4: Specifications
I. Specifications A. Nameplate Rating 1. F-330BAH, F-330BAH-C HOSHIZAKI ICE MAKER MODEL NUMBER SERIAL NUMBER AC SUPPLY VOLTAGE AMPERES DESIGN PRESSURE REFRIGERANT MOTOR-COMPRESSOR THERMALLY PROTECTED, Note: Only the "MODEL NUMBER" is replaced for F-330BAH-C. See the nameplate for electrical and refrigeration specifications. This nameplate is located on the rear panel. -
Page 5: Dimensions/Connections
B. Dimensions/Connections 1. F-330BAH, F-330BAH-C... -
Page 6: Installation And Operating Instructions
II. Installation and Operating Instructions A. Checks Before Installation 1. Install in accordance with all applicable national, state, and local regulations. 2. Remove shipping carton, tape, and packing. If any are left in the icemaker, it will not work properly. 3. -
Page 7: Location
C. Location This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within +45°F to +100°F (+7°C to +38°C); Normal operating water temperature should be within +45°F to +90°F (+7°C to +32°C). Operation of the icemaker, for extended periods, outside of these normal temperature ranges may affect icemaker performance. - Page 8 • Drain line should not be piped directly to the sewer system. An air gap of a minimum of 2 vertical inches (5 cm) should be between the end of the drain pipe from the unit and the floor drain. • This icemaker must be installed in accordance with applicable national, state, and local regulations. • A plumbing permit and services of a licensed plumber may be required in some areas. Fig. 2 Water Supply Inlet 1/2" FPT Piping to approved Drain Outlet drain. 3/4" FPT Floor Drain Shut-Off...
-
Page 9: Final Checklist
G. Final Checklist 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F (+7°C to +38°C) and the water temperature within +45°F to +90°F (+7°C to +32°C) all year around? 3) Is there at least 24"... -
Page 10: Startup
H. Startup 1. All parts are factory-adjusted. Improper adjustments may result in failure. 2. If the unit is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 1) Clean the storage bin. 2) Open the water supply line shut-off valve. -
Page 11: Cleaning And Maintenance
Be careful not to leave any solution in the storage bin. 1. Cleaning Solution Dilute 4.8 fl. oz. (142 ml) of recommended cleaner Hoshizaki "Scale Away" with 0.8 gallons (3 l) of warm water. This is a minimum amount. Make more solution if necessary. - Page 12 6) Lift up the top insulation and unsnap the bin control assembly. Lift the assembly up through the insulation and set it aside. See Fig. 4. 7) Remove the top insulation. 8) Remove the thumbscrews attaching spout (B) to the bin, then remove spout (B). See Fig.
-
Page 13: Sanitizing Solution
19) When the gear motor starts, remove the front panel and move the flush switch to the "FLUSH" position to drain out the water from the icemaker. 20) After the water has drained, move the power switch to the "OFF" position and unplug the unit. - Page 14 4) Remove the top panel. 5) Remove the bin control assembly from the top insulation and set it aside. Remove the top insulation. 6) Remove the thumbscrews attaching spout (B) to the bin, then remove spout (B). 7) Remove the thumbscrews attaching spout (A) and safety bracket (A) to the evaporator assembly, then remove spout (A) and safety bracket (A).
-
Page 15: Maintenance
Consult with your local distributor about inspection and maintenance service. To obtain the name and phone number of your local distributor, call Hoshizaki Technical Support at 1-800-233-1940 in the USA. 1. Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth. Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up. -
Page 16: Preparing The Icemaker For Long Storage
C. Preparing the Icemaker for Long Storage When the icemaker is not used for two or three days under normal conditions, it is sufficient to only move the power switch to the "OFF" position. When storing the icemaker for extended time or in sub-freezing temperatures, turn the water off and drain out all water from the water lines and remove the ice from the bin. - Page 17 HOSHIZAKI AMERICA, INC. 618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A2SA10B...
Need help?
Do you have a question about the F-330BAH(-C) and is the answer not in the manual?
Questions and answers