Hoshizaki B-1150SS Instruction Manual
Hoshizaki B-1150SS Instruction Manual

Hoshizaki B-1150SS Instruction Manual

Ice bin
Hide thumbs Also See for B-1150SS:

Advertisement

Hoshizaki
Hoshizaki America, Inc.
"A Superior Degree
of Reliability"
www.hoshizaki.com
Ice Bin
Model
B-1150SS
B-1300SS
B-1500SS
B-1650SS
INSTRUCTION MANUAL
1
Issued: 2-15-2005
Revised: 8-28-2006

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the B-1150SS and is the answer not in the manual?

Questions and answers

Summary of Contents for Hoshizaki B-1150SS

  • Page 1 Hoshizaki America, Inc. “A Superior Degree of Reliability” www.hoshizaki.com Ice Bin Model B-1150SS B-1300SS B-1500SS B-1650SS INSTRUCTION MANUAL Issued: 2-15-2005 Revised: 8-28-2006...
  • Page 2 HOSHIZAKI provides this manual primarily to assist qualified service technicians in the installation, maintenance and service of the ice bin. Should the reader have any questions or concerns which have not been satisfactorily addressed, please call, write or send an e-mail message to the HOSHIZAKI Technical Support Department. HOSHIZAKI AMERICA, INC.
  • Page 3: Table Of Contents

    • Keep this manual with the bin for later reference. I. Specifications ... 4 A. Dimensions ... 4 1. B-1150SS ... 4 2. B-1300SS ... 5 3. B-1500SS ... 6 4. B-1650SS ... 7 II. Installation Instructions ... 8 A.
  • Page 4: Specifications

    I. Specifications A. Dimensions 1. B-1150SS units: mm [in.]...
  • Page 5: B-1300Ss

    2. B-1300SS units: mm [in.]...
  • Page 6: B-1500Ss

    3. B-1500SS units: mm [in.]...
  • Page 7: B-1650Ss

    4. B-1650SS units: mm [in.]...
  • Page 8: Installation Instructions

    A. Checks Before Installation 1. This ice bin is designed and intended to be used in combination with a Hoshizaki Modular Icemaker. If used with another manufacturer's icemaker, care must be taken to properly support and secure the icemaker in accordance with the manufacturer's recommendations.
  • Page 9: Setup

    C. Setup It is especially important that the ice bin is leveled in both left-to-right and front- to-rear directions. If it is not level, the result could be the production of smaller or irregular shaped cubes or of overflow into the ice bin. See the "LOCATION" instructions on the icemaker.
  • Page 10: Installing The Icemaker

    4) Use the adjustable legs to level the ice bin in both the left-to-right and front-to-rear directions. Single Icemaker Unit 22" WIDE UNIT Top Kit 48" UNIVERSAL Unit 7" B-1150SS Position B-1300SS Cover (3A3198-01) Top Kit Unit B-1500SS Position...
  • Page 11: Drain Connections

    D. Drain Connections See Fig. 3 • A drain outlet, 1" female thread, is located on the bottom of the ice bin. • The drain must have a 1/4" fall per foot on horizontal runs to get a good flow. •...
  • Page 12: Final Check List

    E. Final Check List 1) Is the icemaker/ice bin level? 2) Is the icemaker/ice bin in a site where the ambient temperature is within +45°F to +100°F all year around? (Avoid sites with direct sunlight.) 3) Is there at least 6" clearance around the icemaker/ice bin for easy maintenance and service, and for good ventilation? 4) Have the shipping carton, all tape(s) and packing been removed? 5) Are all components, fasteners and thumbscrews securely in place?
  • Page 13: Operating Instructions

    III. Operating Instructions See Fig. 4 A. Baffle The baffle prevents ice in the bin from flowing out onto the floor while the bin door is open. 1. Removal 1) Rotate the back edge of the baffle up about 6 inches (15 cm). 2) Pull the baffle forward.
  • Page 14: Probe (Optional Accessory)

    C. Probe (Optional Accessory) The probe is used to break apart ice when it has bridged inside the bin and will not flow into the snout. To break apart ice, follow the steps below. 1) Open the bin door. 2) Insert the probe through the hole in the snout (just above the baffle). 3) Carefully move the probe back and forth until ice falls into the snout.
  • Page 15: Cleaning And Maintenance Instructions

    3) Disconnect electrical power to the icemaker. 4) Scrub the inside of the bin, the snout assembly and the sliding door assembly using a nylon scouring pad, brushes 5 oz. of Hoshizaki "Scale Away" diluted in one gallon of water. See Fig. 5.
  • Page 16: Sanitizing Procedure - Following Cleaning Procedure

    Fig. 5 2. Sanitizing Procedure - Following Cleaning Procedure 1) Wash all parts cleaned in the cleaning procedure using the following sanitizing solution: 1/2 fl. oz. of a 5.25% sodium hypochlorite solution (chlorine bleach) diluted in 1 gallon of water. 2) Rinse all parts thoroughly with clean water.
  • Page 17 HOSHIZAKI AMERICA, INC. 618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 91A4LA10D...

This manual is also suitable for:

B-1500ssB-1300ssB-1650ss

Table of Contents