Maytag 9700 series Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Maytag Manuals
  4. Dryer
  5. 9700 series
  6. Installation instructions manual
Maytag 9700 series Installation Instructions Manual

Maytag 9700 series Installation Instructions Manual

Automatic dryer
Hide thumbs Also See for 9700 series:
Table of Contents

Advertisement

Quick Links

AUTOMATIC DRYER INSTALLATION INSTRUCTIONS
MISE EN SERVICE SÉCHEUSE AUTOMATIQUE
INSTRUCCIONES DE INSTALACIÓN DE LA SECADORA
AUTOMÁTICA
The installation, including a proper exhaust system,
is the responsibility of the owner.
La responsabilité de la mise en service, y compris le système
d'évacuation qui convient, revient au propriétaire.
Es responsabilidad del propietario la instalación correcta,
incluso la del sistema de escape.
LEAVE THESE INSTRUCTIONS WITH THE OWNER
REMETTRE CES INSTRUCTIONS AU PROPRIÉTAIRE
DEJE ESTAS INSTRUCCIONES CON EL PROPIETARIO
DC68-02033B-03
1

Advertisement

Table of Contents
loading

Related Manuals for Maytag 9700 series

Summary of Contents for Maytag 9700 series

  • Page 1 AUTOMATIC DRYER INSTALLATION INSTRUCTIONS MISE EN SERVICE SÉCHEUSE AUTOMATIQUE INSTRUCCIONES DE INSTALACIÓN DE LA SECADORA AUTOMÁTICA The installation, including a proper exhaust system, is the responsibility of the owner. La responsabilité de la mise en service, y compris le système d'évacuation qui convient, revient au propriétaire.

  • Page 2: Items Provided

    3. GAS LINES (if a gas dryer) must meet National and Local Codes. 4. EXHAUST SYSTEM – must be rigid metal or flexible stiff walled metal exhaust ducting. See Exhaust Requirements. CABINET DIMENSIONS 9700 series INCH (CM) 6700 series INCH (CM) A.

  • Page 3: Location Considerations

    IMPORTANT TO INSTALLER Please Read The Following Instructions Carefully Before Starting To Install The Dryer. These Instructions Should Be Retained For Future Reference. REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES SUCH AS DRYERS TO AVOID THE DANGER OF A CHILD SUFFOCATING. LOCATION CONSIDERATIONS The dryer should be located to permit adequate room in front for loading the dryer, and sufficient room behind the dryer for the exhaust system.

  • Page 4: Ducting Requirements

    EXHAUSTING Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room. In the United States: • All dryers must be exhausted to the outside. • Only rigid or flexible metal duct should be used for exhausting. In Canada: •...
  • Page 5 ELECTRIC AND GAS DRYER Weather Hood Type Recommended Use only for short run installation 2 1/2”(6,35 cm) 4”(10,16 cm) No. of 90° Rigid Rigid Metallic Flexible* Metallic Flexible* elbows 24.4 m (80 ft.) 12.4 m (41 ft.) 10.1 m (33 ft.) 22.6 m (74 ft.) 20.7 m (68 ft.) 11.2 m (37 ft.)

  • Page 6: Gas Requirements

    Conversion kits from NATURAL to LP, or LP to NATURAL are available through your local Maytag dealer (see Accessories). If other conversions are required, check with the local gas utility for specific information concerning conversion requirements.

  • Page 7: Electrical Requirements

    ELECTRICAL REQUIREMENTS NOTE: Wiring diagram is located below the Top Cover. Export models (not U.S. or Canada): See Additional Instructions for Export Models on the other side of this sheet. • Improper connection of the equipment grounding conductor can result in a risk of electric WARNING shock.

  • Page 8: Electrical Connections

    REPLACEMENT PARTS AND ACCESSORIES If your dryer requires replacement parts or accessories, contact the dealer from whom you purchased your dryer or Maytag Customer Service, Box 2370, Cleveland, Tennessee 37320-2370, phone 423-472-3333, for information on the nearest authorized Maytag Parts Distributor.
  • Page 9 INSTALLATION Parts and literature are packaged inside of dryer drum. To Install... Move dryer to an appropriate location for installation. Consider installing the dryer before the washer in side-by-side installations, to allow access to gas, electrical and exhaust connections. Lay two of the carton corner posts on the floor. Tip the dryer on its side so it will lay across both corner posts.

  • Page 10: Export Models

    3-WIRE SYSTEM CONNECTIONS 1. Loosen or remove center terminal block screw. 2. Connect neutral wire (white or center wire) of power supply cord to the center, silver colored terminal screw of the terminal block. Tighten screw. 3. Connect the other wires to outer terminal block screws. Tighten screws. 4.

  • Page 11: Final Installation Checklist

    With a level, check the dryer, and make necessary adjustments to the leveling legs. At this time, make sure all gas connections (on gas models), exhaust and electrical connections are complete. Plug dryer in, and check operation by using the check list below. (GAS MODELS ONLY) The burner may not ignite initially due to air in the gas line.
  • Page 12 1475 East Woodfield Road Schaumburg, Illinois 60173 Phone: 847-273-3100, for information on product, shipping damage, replacement parts and accessories. Maytag dryer models manufactured for operation on 60Hz AC are not designed for use on 50Hz AC electrical service and conversion of the product from 60 to 50Hz operation is not recommended. For additional information on 50Hz product, contact Maytag International.

  • Page 13: Door Reversal

    Door Reversal 1. Disconnect power supply to unit. 6. Locate door at the other side and reassemble door to dryer. 2. Remove 2 screws on door hinge. 3. Lift the door and remove from dryer. 4. Remove 2 screws on opposite side of door hinge.

This manual is also suitable for:

6700 series

Table of Contents