SPECIFICATIONS <Tuner section> <General> Frequency range Speaker 100 mm cone type (2) 87.5 MHz to 108.0 MHz Output Headphones jack (stereo mini-jack) Antenna: Rod antenna Power output 2.5 W + 2.5 W (EIAJ 7 ohms, T.H.D. 10 % DC), 530 kHz to 1,710 kHz 1.9 W + 1.9 W Antenna: Ferrite bar antenna (DIN 1% Rated Power)
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully CAUTION the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
TRANSISTOR ILLUSTRATION E C B E C B B C E E C B KTA1046Y 2SA1296GR 2SA1979O/Y 2SA933RS 2SC1815Y 2SA933SRS 2SC1740SR 2SC1740SRS DTC124XS DTC114TS 2SC2714O 2SC3052F DTC114YKA DTC114TKA DTC124TKA – 7 –...
ADJUSTMENT <RADIO / TAPE / CD> < RADIO SECTION > < CD SECTION > 1. Focus Bias Adjustment 1. AM Frequency Range Adjustment Make the focus bias adjustment when replacing and repairing • Test Point: TP5 (LCH), TP6 (RCH) the optical block. •...
Page 20
IC DESCRIPTION IC, LC78622NE Description Pin No. Pin Name DEFI Defect detection signal (DEF) input. ("L" is applied when not used.) For PLL/Test input. (Connected to 0V) Phase comparison output to control the external VCO. VVSS – Ground of the built-in VCO. Normally 0V. ISET For the connection of a resistor which adjusts the PDO output current.
Page 21
Pin Name Description Pin No. RVSS – Rch 1-bit DAC/Rch ground. Normally 0V. RCHO Rch output. RVDD – Rch power supply. MUTER Rch muting output. (Not used) XVDD – Power supply of crystal oscillator. XOUT For the connection of a 16.93MHz crystal oscillator. XVSS –...
Page 22
IC, LA9241ML Description Pin No. Pin Name For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF FIN2 signal and subtraction from it create an EF signal. FIN1 For the connection of the pickup photodiode. For the connection of the pickup photodiode.
Page 23
Pin No. Pin Name Description The HFL (high frequency level) signal is used to judge whether the main beam is positioned on the pit or on the mirror. SLOF Sled servo off control input. CV– CLV error signal input from the DSP. RFSM RF output.
Page 24
IC, LC865516A-5T66 Pin No. Pin Name Description SEG E SEG E control. SEG F SEG F control. SEG G SEG G control. Not connected. I-RST Microprocessor reset input. XT1-IN Connected to an external 32.768 kHz crystal oscillator. Not connected. XT2-OUT Connected to an external 32.768 kHz crystal oscillator.
Page 25
Pin No. Pin Name Description Not connected. SEG DP SEG DP control. SEG A SEG A control. SEG B SEG B control. SEG C SEG C control. SEG D SEG D control. Not connected. – 25 –...
COLOR NAME TABLE Basic color symbol Color Basic color symbol Color Basic color symbol Color Black Cream Orange Green Gray Blue Transparent Blue Gold Pink Silver Titan Silver Brown Violet White Transparent White Yellow Transparent Yellow Metallic Blue Light Blue Transparent Green Dark Blue Transparent Orange...
CD MECHANISM EXPLODED VIEW 1 / 1 CD MOTOR C.B PN402 CD MECHANISM PARTS LIST 1 / 1 REF. NO. PART NO. KANRI DESCRIPTION 1 M8-ZZK-E90-070 DA11T3C 2 S2-121-A28-400 COVER GEAR 3 S2-511-A21-000 GEAR MIDDLE 4 S2-511-A21-100 GEAR,DRIVE A S1-PN2-03R-OSE SCR PAN PCS 2-3 –...
Page 37
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111 9301978 2000041 0251431 Printed in Singapore...