Sharp AM-900 Service Manual page 16

AM-900U
9
Install the software on your computer. (The software
allows the machine to be used as a printer and scanner.)
1. Make sure that a USB cable is not connected
to the machine and your computer. (The cable
will be connected in Step 10.)
•
If a cable is connected and a Plug and Play
window appears, close the window and
disconnect the cable.
2. Insert the Sharp CD-ROM into your computer's
CD-ROM drive.
3. Windows XP : Click the start button, click My
R
Computer, and double-click the CD-ROM icon.
Windows 98SE/Me/2000
Computer on the desktop and double-click the
CD-ROM icon.
4. Double-click the setup icon (
ROM window.
5. Follow the on-screen instructions.
When the Setup Type Selection window
•
appears, select Standard to install all of the
software components (this should normally be
selected). If you only wish to install certain
components, select Custom and then select the
components that you wish to install.
• R
In Windows 2000/XP , if a warning message
appears at any time regarding the Windows logo
test or digital signature, be sure to click Continue
Anyway or Yes.
6. When the Finish window appears to indicate that
the selected packages have been installed, click
Close.
If the installation was a Standard Finstallation, the
7.
following window will appear. Click OK.
10
Link each scan menu that you wish to use in
scan mode to a program on your computer.
Windows XP /Me
R R
1. Windows XP : Click the start button, Control
R
Panel, Printers and Other Hardware, and
Scanners and Cameras.
Windows Me : Click the Start button, point to
R
Settings, select Control Panel, and double-click
Scanners and Cameras. (If Scanners and
Cameras does not appear, click view all
Control Panel options).
2. Right-click the SHARP AM-900 icon and select
Properties.
3. The SHARP AM-900 Properties appear. Click
on the Events tab.
4. Select SC1 (scan menu SC1) from the Select an
event list.
5. In the Actions field, select Start this program
and then select the program that you wish to link
to scan menu SC1 from the list of programs.
If you installed the MFP drivers using a Custom
•
installation and did not install Sharpdesk, the
following window will appear. Click OK and go to
Step 10.
The following window will appear. Click Yes to restart
8.
your computer.
: Double click My
R
) in the CD-
9. The Search Setup Wizard will appear. Follow the
on-screen instructions to create an index
database for Sharpdesk.
10. Make sure that the machine's power cord is not
plugged in, and then connect the USB cable to the
USB port on the machine and on your computer.
11. Plug in the machine's power cord.
Windows XP : Follow Steps 12 through 15 to
•
complete the installation of the software.
Windows 2000 : This completes the installation
•
of the software.
Note: If a warning message regarding the
Windows logo test appears (the warning may
appear twice), click Yes each time the window
appears. This will complete the installation of the
software.
You can scan directly from the machine by selecting scan mode and then one of scan menus
SC1 to SC6 on the operation panel. When this is done, the program linked to the selected scan
menu will automatically start on your computer and the image will be scanned to the program.
Microsoft Scanner and Camera Wizard is
•
selected as an example in the window below.
6. Click the Apply button.
7. Repeat Steps 4 through 6 as needed for any of
the other scan menus (SC2 to SC6) that you
wish to use. When finished, click the OK button.
Note: A USB 2.0 or 1.1 cable is required to connect the
machine to your computer. Please purchase this separately.
•
Completing the installation on Windows XP
12. In Windows XP , the Found New Hardware
•
13.
14. After a brief interval, the Found New Hardware
•
R
15. When the wizard finishes installing the software,
R
Windows 2000 /98SE
1. Click the Start button, point to Settings, and
2. In the Control Panel, double-click Scanners and
3. Select SHARP AM-900 and click Properties.
4. Click the Events tab in the SHARP AM-900
5. Select SC1 (scan menu SC1) from the Scanner
6. In Send to this application, select the program
7. Click the Apply button.
8. Repeat Steps 5 through 7 for any of the other
1 – 14
Windows Me /98SE : This completes the
R R
installation of the software.
R
Wizard will appear. Make sure that Install the
software automatically (Recommended) is
selected and click Next.
Note for Windows XP SP2 : The first window of
R
the wizard will ask you if the wizard can connect
to Windows Update. Select No, not this time and
click Next.
If a warning message appears regarding the
Windows logo test, click Continue Anyway.
When the wizard finishes installing the software, click
Finish to close the wizard.
Wizard will appear again. Make sure that Install
the software automatically (Recommended) is
selected and click Next.
If a warning message appears regarding the
Windows logo test, click Continue Anyway.
click Finish to close the wizard. This completes
the installation of the software on Windows XP .
R R
select Control Panel.
Cameras.
Properties.
events list.
(only one) that you wish to link to scan menu SC1.
scan menus (SC2 to SC6) that you wish to use.
When finished, click the OK button.
R
R