PIONEER Service Manual. A subscription to, or additional copies Also test with plug reversed of, PIONEER Ser vice Manual may be obtained at a (Using AC adapter Earth nominal charge from PIONEER. plug as required)
(ADG7021) FOLDER FOLDER PROGRAM REPEAT RANDOM CLEAR TEST TONE CH LEVEL TIMER ENTER DISPLAY DIMMER DISC 1 DISC 2 DISC 3 CD MODE SHIFT DISC 4 DISC 5 DISC SKIP 5.1ch DVD SURROUND SYSTEM This illustration shown by XV-HTD530 XV-HTD530...
Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING FRONT XV-HTD530...
Page 7
ARB7294 Packing Case HTM See Contrast table(2) (English) Operating Instructions ARC7516 (French) (2) CONTRAST TABLE XV-HTD530/KUCXJ and XV-HTD630/KUCXJ are constructed the same except for the following : Mark Symbol and Description XV-HTD530/KUCXJ XV-HTD630/KUCXJ Remote Control Unit AXD7353 AXD7354 Packing Case HTM...
2.2 EXTERIOR SECTION XV-HTD630 ONLY 48 50 Refer to "2.4 TABLE MECHANISM SECTION". Refer to "2.3 FRONT PANEL SECTION". XV-HTD530...
Page 9
DVD Angle HTM ANG7457 Screw BBZ30P140FMC Screw BBZ30P300FZK PCB Angle XNG3057 (2) CONTRAST TABLE XV-HTD530/KUCXJ and XV-HTD630/KUCXJ are constructed the same except for the following : Mark Symbol and Description XV-HTD530/KUCXJ XV-HTD630/KUCXJ AF Assy AWU8074 AWU8075 Rear Panel HTM ANC8203...
2.3 FRONT PANEL SECTION 16 (1/2) 16 (2/2) XV-HTD530...
Page 11
BPZ30P100FMC Sensor Cushion XEB3026 VOL Knob HTM AAK8098 FL Fiiter HTM AAK8100 (2) CONTRAST TABLE XV-HTD530/KUCXJ and XV-HTD630/KUCXJ are constructed the same except for the following : Mark Symbol and Description XV-HTD530/KUCXJ XV-HTD630/KUCXJ Front Panel Assy HTM AXG7217 AXG7218 Display Window HTM...
6CH AMP ASSY (AWM7720) DIODE L DIODE S ASSY ASSY (AWU8070) (AWU8071) POWER TRANSFORMER AMP TRADE ASSY (ATS7354) (AWU8059) POWER CORD (ADG7021) SYSTEM DOWNLOAD MOTOR (TRAY) (DXM1143) MOTOR LOMB (LOADING) ASSY (VXM1033) (AWU8156) VNK1277 DVD TRADE ASSY (AWU8072) STEPPING MOTOR (VXM1101) XV-HTD530...
Page 21
DC FAN MOTOR (AXM7025) XV-HTD630 ONLY AKE7097 1/4 - AF ASSY (XV-HTD630 : AWU8075) (XV-HTD530 : AWU8074) DISPLAY ASSY (AWU8058) HP MIC ASSY (AWU8064) DSP TRADE ASSY (AWU8060) 1/2 - DSP ASSY (AWX8251) XV-HTD530...
3.4 TRSB, SSRB, LOMB and SSIB ASSYS SSRB ASSY (AWU8155) TRSB ASSY (AWU8154) TRAY MOTOR DXM1143 LOMB ASSY (AWU8156) CARRIAGE MOTOR (LOADING) : VXM1033 CN123 : The power supply is shown with the marked box. A B C XV-HTD530...
Page 23
: RF SIGNAL ROUTE : FOCUS SERVO LOOP LINE : TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE PICKUP ASSY-S (OXX8005) (RF) (RF) (RF) (RF) (RF) (RF) CN121 SSIB ASSY (AWU8157) SPINDLE MOTOR : VXM1099 CN122 STEPPING MOTOR : VXM1101 XV-HTD530...
Page 25
DVDM ASSY (AWM7814) (RF) : RF SIGNAL ROUTE (DVD) : DVD DATA SIGNAL ROUTE : FOCUS SERVO LOOP LINE : TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE (DVD) (DVD) : The power supply is shown with the marked box. XV-HTD530...
3.9 FM/AM TUNER MODULE FM/AM TUNER MODULE (AXQ7228) FM FRONT END (FM) (FM) (FM) (FM) (FM) (AM) (AM) (AM) AM RF TUNING BLOCK (FM) (AM) OSC : 981 - 2052kHz 9k step XV-HTD530...
Page 33
: The power supply is shown with the marked box. (TX) : TUNER AUDIO SIGNAL ROUTE (AM) : AM SIGNAL ROUTE (FM) : FM SIGNAL ROUTE (AM) (TX) (FM) (TX) (TX) (TX) (FM) (FM) (TX) (AM) L201 ATE7003 XV-HTD530...
3.13 AF(4/4), DIODE L and DIODE S ASSYS DIODE L ASSY (AWU8070) DIODE S ASSY (AWU8071) (FL) (SW) (SL) (FL) (SW) (SL) 1/4-3/4 XV-HTD530...
Page 41
: The power supply is shown with the marked box. (SL) : AUDIO SIGNAL ROUTE (Surround L ch) : AUDIO SIGNAL ROUTE (Center ch) (SW) : AUDIO SIGNAL ROUTE (Sub Woofer ch) AF ASSY (XV-HTD630 : AWU8075) (XV-HTD530 : AWU8074) (FL) (FL) (FL) (FL) (FL) (SW) (FL)
: AUDIO SIGNAL ROUTE (Surround L ch) : AUDIO SIGNAL ROUTE (Center ch) (SW) : AUDIO SIGNAL ROUTE (Sub Woofer ch) • NOTE FOR FUSE REPLACEMENT FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. CAUTION - M N P REPLACE WITH SAME TYPE AND RATINGS ONLY. XV-HTD530...
Page 49
: VIDEO SIGNAL ROUTE (PR/R) (CY/G) : S VIDEO SIGNAL ROUTE (Y) : VIDEO SIGNAL ROUTE (CY/G) (C/V) (PB/B) : S VIDEO SIGNAL ROUTE (C/V) : VIDEO SIGNAL ROUTE (PB/B) : The power supply is shown with the marked box. SYSTEM DOWNLOAD XV-HTD530...
(FL) (FL) (FL) LOMB AWU8156- (FL) CN31 LOADING MOTOR LOMB AWU8156- (ANP7473-A) (ANP7473-A) LOMB ASSY FUNCTION KEY ASSY (AWU8062) A B C A B C : The power supply is shown with the marked box. Q S T U XV-HTD530...
Symbol In PCB Symbol In Schematic Part Name Diagrams Diagrams C E B Capacitor Connector Transistor B C E SIDE A Transistor with resistor B C E Field effect SIDE B P.C.Board Chip Part transistor Resistor array 3-terminal regulator XV-HTD530...
POSITION SSRB POSITION SSRB AWU8155- DISC AWU8155- SENSOR FR1S (ANP7473-A) (ANP7473-A) SSRB ASSY SSRB ASSY CN123 SIDE A SIDE B CN31 CN31 LOMB AWU8156- CN31 LOADING MOTOR LOMB AWU8156- (ANP7473-A) (ANP7473-A) LOMB ASSY A B C A B C XV-HTD530...
DVD TRADE ASSY SIDE B CN5107 ASS'Y TRADE AWU8072- CN5106 CN5108 (ANP7457-D) SSIB ASSY SSIB ASSY SIDE B SIDE A SSIB SSIB SSIB AWU8157- AWU8157- FR1S STEPPING MOTOR Contact Side Contact Side Contact Side Contact Side (ANP7473-A) (ANP7473-A) SPINDLE MOTOR CN122 XV-HTD530...
CN3021 CN3022 CN3021 CN3022 UPSIDE W136 CAUTION W137 GNDA REPLACE WITH SAME TYPE W154 NO.491007 FOR IC25 W155 MFD.BY LITTELFUSE INC. W156 AMP TRADE ASSY W153 AWU8059 W152 CMK-P3X CN3011 CN3012 CN3011 CN3012 (ANP7456-B) CN3031 CN3032 L M N XV-HTD530...
W132 W129 W128 STAND BY W120 W119 CMK-P3X CONTACT SIDE CN52 SECONDARY IC51 CN51 (ANP7456-B) VIDEO JACK ASSY VIDEO ASSY W118 AWU8061 W117 W114 W113 CN5103 W112 JA8802 JA8851 CMK-P3X CONTACT SIDE UP CN8003 CONTACT SIDE UP (ANP7456-B) XV-HTD530...
4.9 FM/AM TUNER MODULE SIDE A FM/AM TUNER MODULE SIDE A CN5701 CN201 (ANP7338-B) Q202 FM/AM TUNER MODULE SIDE B (ANP7338-B) Q201 IC201 Q203 Q205 IC202 Q204 XV-HTD530...
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors). 5.62k Ω 562 x 10 5621 RN1/4PC 5 6 2 1 LIST OF WHOLE PCB ASSEMBLIES XV-HTD630 XV-HTD530 Mark Symbol and Description /KUCXJ /KUCXJ 1..FM/AM TUNER MODULE AXQ7228 AXQ7228 1..MECB ASSY...
[Electrical Part] screw screw Electrical adjustments are not required. 6.3 JIGS AND MEASURING INSTRUMENTS Test mode remote control Screwdriver (large) Screwdriver (medium) TV monitor unit (GGF1381) Screw tight (GYL1001) DVD test disc Precise screwdriver Soldering iron (GGV1025) XV-HTD530...
Exchange the Traverse Mechanism point Electric point ∗ After adjustment, screw locks Mechanical Ÿ Exchange the Spindle Motor point with the Screw tight. Electric point Exchange PCB Assy Mechanical Exchange PC Board point LOAB and DVDM ASSY Electric point XV-HTD530...
Perform only trace, video and audio outputs are nothing. < When playback with the target address of disc (DVD)> For example, when playback with # 30000 During PLAY CHP/TIM Press keys in order 030000 TEST MODE: OFF POWER GGF1381 Test mode remote control unit XV-HTD530...
Mechanism Base and turn each screw to adjust Turn the Short switch to Short side when the height. (Refer to "6.2 ADJUSTMENT ITEMS AND removing the Pickup Flexible Cable. LOCATION".) (Refer to "7.1.13 DISASSEBLY".) Turn a flat side into bottom XV-HTD530...
Page 86
J : Min If error rate is OK, Disc playback normally. locks a root of • The measurement of block error rate tangential and radial adjustment screws with the Screw tight, and go to step Screw tight: GYL1001 Test mode end XV-HTD530...
Perform only trace, video and audio outputs are nothing. = Screen display ON/OFF 1. Turn off the display by pressing the [AUDIO] (A8-1E) key of the remote control unit. 2. Turn on the display by pressing the [DISPLAY] (A8-43) key of the remote control unit. XV-HTD530...
Page 88
• After the search, perform only trace and video and audio outputs are nothing. 4. Release the Search address input • Clear the address by pressing the [CLEAR] (A8-45) key. Release the address input mode when pressing the [CLEAR] key once again. XV-HTD530...
Kinds of version / firmware of the FE. Scart terminal output [SK – ∗ ∗] RAM or ROM (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] XV-HTD530...
• Region confirmation mode (ESC + AUDIO [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys) After you press the AUDIO key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. XV-HTD530...
(version of ST core software) softwareVersion . softwareRevision / buildNumber 0 F.E VERSION Version of FRONT END (version of mechanism controller CHIP software) MainVersion / Kinds of firmware RAM or ROM - Remote control code = Key code of Main unit XV-HTD530...
PLL lost timeout 0x93 DECODER ERROR 0xa∗ DECODER TIMEOUT 0xb∗ Note : 0 x & & ID lost error 0xa3 ID lost timeout 0xb3 DEVICE ERROR 0xd∗ code SRAM error 0xd1 (Only this part is displayed to a display) XV-HTD530...
Page 94
DVD/CD S E R V I C E LINE2 S E R V I C E TUNER S E R V I C E S E R V I C E LINE1 S E R V I C E XV-HTD530...
Page 95
Do move to inner and outer periphery 1. Stepping motor of the stepping in the test mode? 2. Inside switch Stepping move timeout 0 x 54 Did timeout at stepping movement Do indicate "S-04" at the most inner 3. Driver periphery of the stepping? XV-HTD530...
Page 96
SRAM error 0 x d1 Cannot access SRAM 2. Front End IC Is not bus line short-circuiting? 3. Front End-SRAM bus line FAILSAFE (0 x e∗) 1. software runaway Unexpected error 0 x e1 Unexpected error 3. Software bug XV-HTD530...
(The SEARCH key is not accepted after all 9 digits have been entered.) Input ID Number ! [Player's ID Number Setting] ID Number ? > 0 0 0 0 0 0 0 0 1 OK ? <PLAY> Compare Mode <SEARCH> Enter Input ID Number ! XV-HTD530...
Page 98
[Player's ID Number Setting] ID Number ? [ 0 0 0 0 0 0 0 0 1 ] Compare > 0 0 0 0 0 0 0 0 1 OK? <PLAY> Enter <STOP> Memory Clear Input ID Number ! XV-HTD530...
Page 99
• Indication when the data have not been set If no ID data are set after the ID number is changed, the message "NO ID DATA" flashes on the screen and FL display for a few seconds after the power is turned on or during Stop mode. XV-HTD530...
The unit recognizes that an operation key voltage at Pins 18 and 19 of the KEY input terminal is 5 All operation keys are disabled. has already been pressed. V. If it is not, check if the operation switch on the line is in failure. XV-HTD530...
• Is a signal output from IC601-pin 114 (ROT DRV) on the DVDM BACK END IC (DVDM IC601) Assy ? (Is a signal fluctuating of 0-3.3V ?) • Is the motor drive voltage output it at CN124 pin 7 and pin 8 ? IC151 and peripheral parts of the DVDM Assy XV-HTD530...
Page 102
"NO ID DATA" flashes on the screen and FL display for a few (Picture is normal) Is signal output from DOUT signal (CN911-pin 21) on the DVDM Assy ? DVDM CN911-pin 21 seconds after the power is turned on or during Stop mode. XV-HTD530...
Page 103
Stop mode. When the rotary tray rotates, a rattling sound is heard. • Breaking or damage of the disc detect Even during playback, the indication "NO DISC" is displayed. sensor (PC21) It takes longer than normal until playback starts. XV-HTD530...
Page 104
Disc Detect Sensor Flexible Cable (7P) : VDA1835 (PC21 : GP2S28) (TRSB CN12 ↔ SSRB CN21) Rotary Tray : VNK4923 Open Open Close Close Motor : DXM1143 Tray Open/Close (for Rotary Tray Drive) Position Detect SW (S21 : VSK1011) XV-HTD530...
3V→5V conversion Replace IC8702. Is connector Insert it tightly. for pin 17 ? inserted tightly Pin 5 Do perform 3V→5V conversion Replace IC8702. for pin 15 ? Pin 7 Do perform 3V→5V conversion Replace IC8702. for pin 13 ? XV-HTD530...
Page 106
Pin 16 Do perform Step 4 5V→3V conversion Replace IC8701. for pin 4 ? IC8701 Pin 18 Pin 3 Do perform Do perform 5V→3V conversion Replace IC8701. 5V→3V conversion Replace IC8701. for pin 2 ? for pin 17 ? XV-HTD530...
Page 107
"NO ID DATA" flashes on the screen and FL display for a few seconds after the power is turned on or during Stop mode. BCK (pin 26) Replace IC8201. outputting it? IC8502-pin2 20MHz clock Replace IC8502 or X8501. outputting it? XV-HTD530...
Page 108
4 ? a signal output Replace IC8401. IC8701 Pin 18 Pin 3 Pin 28 Do perform Does Do perform 5V→3V conversion Replace IC8701. a signal output Replace IC8401. 5V→3V conversion Replace IC8701. for pin 2 ? for pin 17 ? XV-HTD530...
• If no pulse is input to the AC terminal (Pin 4) for about 60 msec when the microcomputer is in Memory Backup mode, it will not do any processing. • The unit will recover from Memory Backup mode if a reset command is input to the XRESET terminal (Pin 8). XV-HTD530...
R833 → The microcomputer detects the XPROTECT level and C851 C813 R823 R832 R843 C830 C871 R831 R844 C809 R878 R830 shuts the power to the unit off. R838 R837 R836 C803 C816 R829 C801 C802 C815 Front Side XV-HTD530...
Page 113
Q106 is turned on, and the level of the XPROTECT line becomes D3658, Q3651 (E, C, B) is turned off, Q3651 (E2, B2, C2) is low. ← The microcomputer detects the XPROTECT level and shuts turned on, and the level of XPROTECT becomes low. the power to the unit off. XV-HTD530...
Page 114
When the temperature at TH131 reaches 107-125_C (varying according to conditions,) the voltage at Point (A) becomes high enough to turn Q131 on, and the level of the XPROTECT line becomes low. The microcomputer detects the XPROTECT level and shuts the power to the unit off. XV-HTD530...
Page 115
When the temperature at TH131 reaches 107-125_C (varying according to conditions,) the voltage at Point (A) becomes high enough to turn Q131 on, and the level of the XPROTECT line becomes low. The microcomputer detects the XPROTECT level and shuts the power to the unit off. XV-HTD530...
Page 116
Q3632 (E2, C2, B2), Q3633, and Q3636 (E, C, B) are turned on, the line to activate the SP relay becomes low level, and the SP Relay is turned off. (2) HP MUTE Q3635 is turned on, and the MUTE circuit for HP is turned on. XV-HTD530...
Table Mechanism Section When reattaching the bonnet, to avoid damaging the unit, hook the bonnet by supporting and lightly pushing it upward by hand from the rear, as shown in the photo below. Gear Pulley Bonnet Gear Pulley Hook Bottom View XV-HTD530...
Page 118
Front Panel Section Remove the bonnet and tray cap. (See Step ¥.) Remove the three screws. Remove the one screw. Remove the four hooks. GND Plate L HTM ×3 Remove the Front Panel Section. Front Panel Section XV-HTD530...
Page 119
Short-circuit two points of C and D by soldering. Note : After replacement, connect the flexible cable, then remove the soldered joint (open). Rear Panel Reattatch the clamper holder by tighten the two screws. DVDM Assy Rear View Table Mechanism Section Table Mechanism Section DISPLAY Assy XV-HTD530...
Page 120
CN5107 CN911 To DVDM Jig cable To DVDM CN911 (GGD1222) CN953 DVDM Assy Insert the insulation sheet between the DVDM Assy and the chassis. Arrange the cables as shown in the photo below. To CN5105 Insulation sheet DVDM Assy XV-HTD530...
Page 121
Assy AMP TRADE Assy CN3031 CN3032 ×2 ×2 AMP Module Section Connect the two jig cables. Arrange the cables as shown in the photo below. ×2 Jig cable (GGD1315) AMP TRADE Assy CN3031 CN3032 CN3011 CN3012 6CH AMP Assy XV-HTD530...
Page 122
Arrange the cables as shown in the photo below. Connect the AF Assy with the AMP Module Section using a jig cable. Table Mechanism Section AF Assy Jig cable (GGD1315) DVD Angle HTM AF Assy DVD TRADE Assy PRIMARY Assy Reattach the DVDM Assy. AMP Module Section XV-HTD530...
Note : After replacement, connect the flexible cable, then remove the soldered joint (open). Remove the four screws. Disconnect the three flexible cables and the one connector. Remove the Table Mechanism Section. Rear View DVDM Assy Rear Panel Table Mechanism Section Table Mechanism Section XV-HTD530...
Page 124
Tighten. Note: It is not necessary to set the Disc No. of the rotary tray, because the Automatic Disc No. Detection system will function. Adjust the position of the rotary tray so that the center hole can be seen. XV-HTD530...
Page 125
Mechanism Base Section Barrier A HTM Mecha Frame HTM Arrangement of the flexible cables when reassembling Barrier A HTM 8P Flexible cable 17P Flexible cable 24P Flexible cable 2P Wire cable DVDM Assy To DVDM Assy Mecha Frame HTM XV-HTD530...
Page 126
Styling the flexible cable installation 17P Flexible cable Remove the five screws. 24P Flexible cable Remove the Traverse Mecha. Assy-S. ×2 Traverse Mecha. Assy-S ×4 Float Rubber Note on the Float Rubber Installation Pole of the Float Base ×2 Float Rubber ×2 Hook XV-HTD530...
Page 127
Mount the Table Mechanism Section on the Mechanism Base Section. Connect the flexible cable. Bring an extra flexible cable close to the front side. Mechanism Base Section Flexible cable Side View Side View Table Mechanism Section XV-HTD530...
Page 128
If the boss is set in this position, the unit does not operate correctly. If the boss is set in the cam groove, the unit operates correctly. Table Mechanism Section Table Mechanism Section Cam groove Mechanism Base Section Planet Base Boss part XV-HTD530...
Page 129
Notes on Assembling the Mechanism Section Clamper Plate Tray Gear Motor (for Tray) Motor Pulley (for Tray Motor) Motor Holder Worm Gear, Tray Belt Motor (for Loading) Motor Pulley (for Loading Motor) XV-HTD530...
Page 130
Apply lubricating oil (GYA1001) to the holder part. Motor Holder Apply lubricating oil (GYA1001). Clamper Plate Motor (for Loading), Motor Pulley (for Loading Motor) Adjust the height of the motor pulley to 6.2mm. Motor Pulley 6.2mm Motor Apply lubricating oil (GYA1001). XV-HTD530...
• The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. • List of IC STM6316ATXXZ, STI5588CVB, PDC111A 7 STM6316ATXXZ (DVDM ASSY : IC301) • FRONT END IC ¶ Block Diagram XV-HTD530...
Page 132
¶ Pin Function t i c t i c t s i t s i t s i t s i t s i t i s t i s XV-HTD530...
Page 133
- t l l i c y t i - t l l i c y t i - t l l i c y t i d l l XV-HTD530...
Page 139
: ' L : ' L u : ' ' L ' t i r ' t i . ' L ' L ' ' L ' ' L ' ' L ' XV-HTD530...
Page 140
. r i y t i l a i n i l n i l XV-HTD530...
Page 141
. r i n i l c i t i t i c i t i t i l b i XV-HTD530...
Page 142
Chip select 1 for system bus XHPMUTE HP MUTE ON/OFF XRECMUTE REC OUTPUT MUTE ON/OFF XMUTEC Cch MUTE ON/OFF REAR RELAY ON/OFF RYFSC FRONT/SW/CENTER RELAY ON/OFF TIMERLED Control TIMER LED LEVELSHIFT VOL 0 to 5 : H VSS4 VSS4 VDD4 VDD4 XV-HTD530...
Page 143
WIRE LESS OUTPUT SELECT A INPUTSELB AUDIO INPUT SELECT B INPUTSELA AUDIO INPUT SELECT A XTL0 Selection X'tal to DIR DIRERR LOCK/UNLOCK from DIR DIRRST Reset to DIR /CODEC DIRCS Chip select to DIR/CODEC PB7/D7 DIRDO Data input from DIR/CODEC XV-HTD530...
Page 144
• PortE and PortF can be selected for input or output by each 2 bits. • In case of without RDS, it is best that RDSDATA and RDSCLK are assigned as I/O port which can be set output and output low level. XV-HTD530...
Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 Position to be cleaned Cleaning tools Fans Cleaning paper : GED-008 XV-HTD530...
18 Timer indicator Press to start playback of any disc in the player. Lights when the timer is set. This mark indicates compatibility with DVD-RW discs recorded on a DVD recorder in Video Recording(VR) mode. 20 PHONES jack Headphone jack. XV-HTD530...
Page 148
Lights when the sleep timer is active Lights when either the W.Surr. or W.Stereo mode is selected. PRO LOGIC II 22 V.PART Lights during Dolby Pro Logic decoding. Lights when a playing a video part of a DVD disc. XV-HTD530...
Press to change the camera angle during • Use with SHIFT for QUIET/MIDNIGHT: Use to select DVD multi-angle scene playback. the Quiet and Midnight modes. ZOOM 14 RETURN Press to change the screen zoom level. Press to return to a previous menu screen. XV-HTD530...
Page 150
Use to select a repeat play mode. Press to switch between modes with the wireless speaker system. RANDOM (SHIFT +3) Use to select a random play mode. TEST TONE (SHIFT + 4) Use to output the test tone (for speaker setup). XV-HTD530...