Denon AVR-1312 Getting Started page 71

GAudioH
Symptom
Audio is not output. • Check the connections for all devices.
• Check the speaker connections and configurations.
• Check whether the audio device power is turned on.
• Adjust the master volume.
• Cancel the mute mode.
• Select a suitable input source.
• Select a suitable input mode.
• Disconnect the headphones. No sound is output from the speakers
or the PRE OUT connectors when headphones are connected.
No sound is • Check if the surround speakers are connected to the SURROUND
produced from terminals.
surround speaker.
No sound is • Set "Speaker Config." – "Surround Back" on the menu to
produced from something other than "None".
surround back • Set the surround mode to something other than "STEREO".
speaker.
No sound is • Check the subwoofer connections.
produced from
subwoofer. • Turn on the subwoofer's power.
• Set "Speaker Config." – "Subwoofer" on the menu to "Yes".
• If "Front" and "Center" for "Speaker Config." are set to "Large",
and "SW Mode" is set to "LFE", no sound may be output from
the subwoofers, depending on the input signal or selected
surround mode.
DTS sound is not • Set "Decode Mode" on the menu to "Auto" or "DTS".
output.
Dolby TrueHD, DTS- • Make HDMI connections.
HD, Dolby Digital
Plus audio is not
output.
• Check that "Speaker Config." – "Center" or "Surround" is set
Dolby PLg mode or
to other than "None". If the speaker system is 2.0/2.1ch, this
DTS NEO:6 mode
surround mode cannot be selected.
cannot be selected.
• When headphones are used, Dolby PLg or DTS NEO:6 cannot be
selected.
RESTORER cannot • Check that an analog signal or PCM signal (fs=44.1/48 kHz) is
be selected. input. For playback of multichannel signals such as Dolby Digital
or DTS surround, RESTORER cannot be used.
Cause/Solution
GRadioH
Page Symptom
Reception fails, or • Change the antenna orientation or position.
C 4,
there is a lot of noise • Separate the AM loop antenna from the unit.
5, 7, 8,
or distortion. • Use an FM outdoor antenna.
9, 10
• Separate the antenna from other connection cables.
C 3,
24, 25
GControl dock for iPodH
–
Symptom
11
11
iPod cannot be • Check the iPod connections.
11
played. • Insert the AC adaptor of the iPod control dock into the power
32
outlet.
42
• Switch the input source to "DOCK".
"Connection Error" • Unable to communicate properly. Turn off the power to this unit,
–
is displayed. disconnect the iPod and then reconnect it.
• The iPod is not responding. Turn off the power to this unit,
disconnect the iPod and then reconnect it.
C 6
"Not Support" is • The iPod connected to the unit is not compatible. Please make
displayed. sure the iPod you are connecting is compatible.
19
• The software version of the connected iPod is an old one. Please
update to the latest version.
C
3,
GRemote Control UnitH
24, 25
Symptom
C 4
C 6
The set cannot be • Batteries are worn out. Replace with new batteries.
C 5,
operated with the • Operate the remote control unit within a distance of about
C 6
remote control unit. 23 ft/7 m from this unit and at an angle of within 30°.
• Remove any obstacle between this unit and the remote control
unit.
32
• Insert the batteries in the proper direction, checking the q and
w marks.
• The set's remote control sensor is exposed to strong light (direct
5
sunlight, inverter type fluorescent bulb light, etc.). Move the set
to a place in which the remote control sensor will not be exposed
to strong light.
C 5
–
39
56
Cause/Solution
Cause/Solution
Cause/Solution
Page
10
10
10
10
Page
9
–
11
–
–
–
–
Page
46
46
46
46
46