Download  Print this page

Honeywell Dolphin 7850 User Manual

Honeywell international inc. mobile computer user's guide.
Hide thumbs

Advertisement

®
Dolphin
7850 Mobile Computer
®
With Windows Mobile
5.0
User's Guide

Advertisement

   Related Manuals for Honeywell Dolphin 7850

   Summary of Contents for Honeywell Dolphin 7850

  • Page 1 ® Dolphin 7850 Mobile Computer ® With Windows Mobile User’s Guide...
  • Page 2 Honeywell. Honeywell shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
  • Page 3: Table Of Contents

    Table of Contents Chapter 1 - Agency Information Label Locations ...1-1 Regulatory and Safety Approvals for all Dolphin Terminals ...1-2 FCC Compliance...1-3 Chapter 2 - Getting Started Out of the Box ...2-1 Today Screen...2-2 Navigation Bar ...2-2 Using the Stylus ...2-3 Pop-Up Menus ...2-3 Chapter 3 - Hardware Overview Standard Terminal Configuration ...3-1...
  • Page 4 Chapter 5 - Using the Imager Scanner Engine Overview... 5-1 Available Engines ... 5-1 Available Laser Engines ... 5-2 Supported Bar Code Symbologies ... 5-3 Activating the Engine... 5-4 Decoding ... 5-5 Capturing Images ... 5-7 Chapter 6 - System Settings Overview...
  • Page 5 Discovered Devices... 8-10 Refreshing Discovered Devices... 8-10 Making the Terminal Discoverable ... 8-10 Pairing ... 8-13 Chapter 9 - Dolphin HomeBase Device Overview... 9-1 Front Panel ... 9-2 Back Panel ... 9-3 Bottom Panel Dimensions ... 9-4 Powering the HomeBase Device... 9-5 Charging the Main Battery...
  • Page 6 Limited Warranty ... 13-3 Rev C Dolphin® 7850 Mobile Computer 4/30/2008 User’s Guide...
  • Page 7: Chapter 1 - Agency Information

    Dolphin mobile computer. Dolphin 7850 802.11b/g (WLAN) & Bluetooth Dolphin 7850 RF terminals are designed to comply with the most current applicable standards on safe levels of RF energy developed by the Institute of Electrical and Electronics Engineers (IEEE) and the American National Standards Institute (ANSI) and has been recommended for adoption by the Federal Communications Commission (FCC).
  • Page 8: Regulatory And Safety Approvals For All Dolphin Terminals

    5627 BT Eindhoven The Netherlands Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive. 1 - 2...
  • Page 9: Fcc Compliance

    The correction is the responsibility of the user. Use only shielded data cables with this system. In accordance with FCC 15.21, changes or modifications not expressly approved by Honeywell may void the FCC authorization to operate the equipment.
  • Page 10: Canadian Compliance

    Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada. For European Community Users Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic equipment (WEEE).
  • Page 11 You may also contact your supplier for more information on the environmental performances of this product. Pacemakers, Hearing Aids and Other Electrically Powered Devices Most manufacturers of medical devices adhere to the IEC 601-1-2 standard. This standard requires devices to operate properly in an EM Field with a strength of 3V/m over a frequency range of 26 to 1000MHz.
  • Page 12 1 - 6 Rev C Dolphin® 7850 Mobile Computer 4/30/2008 User’s Guide...
  • Page 13: Chapter 2 - Getting Started

    • Main battery pack (7.4v, li-ion) • Getting Started CD-ROM • Dolphin 7850 Mobile Computer Quick Start Guide Be sure to keep the original packaging in the event that the Dolphin terminal should need to be returned for service. For details, see If you ordered additional peripherals and accessories, verify that they are included with the order.
  • Page 14: Today Screen

    Today Screen Initial boot and system resets end on the Today screen; see Tap to access the Start menu Note: You can also open the Today screen at any time by tapping Start > Today. Navigation Bar Located at the top of every screen, the Navigation bar provides access to the Start menu, shows the current time (from the system clock), and displays both status and keyboard status icons.
  • Page 15: Using The Stylus

    Using the Stylus Use the stylus or your finger to select or enter information on the touch panel. The stylus functions as a mouse; generally, a tap is the same as a click. Tap the touch panel once to open menu items and select options. Drag Hold the stylus on the screen and drag across the screen to select text and images.
  • Page 16 2 - 4 Rev C Dolphin® 7850 Mobile Computer 4/30/2008 User’s Guide...
  • Page 17: Chapter 3 - Hardware Overview

    • WLAN radio (Wi-Fi certified) • Bluetooth radio Additional Configuration Options The Dolphin 7850 terminal offers you a number of configuration options to customize the terminal to your business needs. System Memory Additional 64MB of RAM (for a total of 128MB RAM); see...
  • Page 18: Peripherals

    There are a number of cable kits that enable you to charge and communicate with other devices. For more information, see Cables Kits Dolphin ChargeBase This charging bay holds up to four(4) Dolphin 7850 terminals. For more information, see Dolphin ChargeBase Mobile Mount The Mobile Mount is a plastic cradle and RAM mount that holds and positions the terminal and can be mounted on a fork truck, pallet lift, or other stable, stationary surface.
  • Page 19: Accessories

    Accessories The following items are sold separately as part of a complete installation. Battery Door Tether For more information, see Battery Door Tether (Optional) Holster The holster holds one terminal around the waist. Li-ion Battery Pack These are 7.4Vdc, 14.1 watt hour Li-on replacement battery packs; see Protective Cover The protective cover wraps around the terminal to protect it from wear and tear.
  • Page 20: Front Panel Features

    Front Panel Features 3.5 inch 1/4 VGA Touch Panel Display Decode LED Decode and Scan LEDs The Scan LED lights red when you press the Scan trigger in scanning applications. The Decode LED lights green when a scanned bar code is successfully decoded. For more information, see Keyboard Protection Ribs These ribs protect the keyboard and prevent keys from being pressed accidentally when the...
  • Page 21: Back Panel Features

    Back Panel Features Battery Door Tether Holes Battery Door The battery door covers and secures the main battery pack in the battery well. There is a mechanical switch on the terminal under this door that puts the terminal in suspend mode (see page 3-15) while the battery door is open.
  • Page 22: Side Panel Features

    Pistol-Grip Stylus Loop Stylus Slot Note: This graphic shows the right side of the Dolphin 7850 terminal. Angled Display The touch panel display (see page 3-4) tilts up toward the user, which improves application viewing when operating the terminal and reduces glare. Most important, the tilted display helps you read decoded data without having to tilt your wrist.
  • Page 23: Battery Door Tether (optional)

    The scan trigger also wakes the terminal from Stylus Slot Dolphin 7850 terminals ship with a stylus inserted into the pistol-grip handle. Stores the stylus in this slot when you’re not using it. For more information about the stylus, see on page 2-3.
  • Page 24 4. Remove the battery door. 5. Take the clip piece, loop the lanyard through the tether holes on the battery door as shown below. 6. Reattach the battery door. 7. Snap the leather strap into the clip. 3 - 8 Rev C Dolphin®...
  • Page 25: I/o Connector

    I/O Connector I/O Connector This I/O connector has 17 pins that are designed to work exclusively with Dolphin 7850 peripherals and cables. This connector • Powers the terminal. • Charges the main battery. • Supports communication with a host workstation via Microsoft ActiveSync (see page 7-3).
  • Page 26: Rubber Bumpers

    Rubber Bumpers There are two sets of rubber bumpers: one set below the scan engine window and the other set on the bottom front of the pistol-grip handle. Rubber bumpers enable you to set the terminal down on a flat surface with easy access to the handle, so you can pick up and put down the terminal with ease.
  • Page 27: Battery Power

    Both batteries work together to prevent data loss when the terminal is used over long periods of time. Main Battery Pack Use only the Li-ion battery packs provided by Honeywell. Use of any battery not sold/manufactured by Honeywell may result in damage not covered by the warranty.
  • Page 28: Internal Backup Battery

    Charging Options When the battery is installed in the terminal, you can insert the terminal into any one of the following peripherals to charge the main battery pack: • Dolphin HomeBase Device (see page 9-1) • Dolphin ChargeBase (see page 11-1) •...
  • Page 29 99 (would warn whenever the charge drops below 99%). 4. Tap OK to save changes. Note: For more information about the RegEdit Power Tool, refer to the Dolphin Power Tools User’s Guide, which is available for download at www.honeywell.com/aidc. Dolphin® 7850 Mobile Computer User’s Guide...
  • Page 30 • Excessive discharge damages a battery. Recharge the battery when your terminal indicates low battery power. • If you observe that the battery is physically damaged in some way, please send it to Honeywell or an authorized Honeywell service center for inspection.
  • Page 31: Resetting The Terminal

    Resetting the Terminal There are two ways to reset the Dolphin terminal: a soft reset and a hard reset. Soft Reset (Warm Boot) A soft reset re-boots the device without losing RAM data. You would perform a soft reset 1) when the terminal fails to respond, 2) after installing software applications that require a reboot, or 3) after making changes to certain system settings.
  • Page 32 Troubleshooting If the terminal does not wake when you press the scan trigger, • The battery door may not be fully closed. The mechanical switch under the battery door prevents the terminal from resuming operation until the door is closed. •...
  • Page 33: Technical Specifications

    Technical Specifications Feature Description Basic Features Form Factor: Purpose-built, compact, handle-style mobile computer Operating System: Windows Mobile 5.0 Development Hand Held Products Dolphin SDK for Visual Studio 2005–supports C/C++, C# and Visual Basic development on Visual Studio 2005 Environment: Third Party Software: SOTI MobiControl (remote device management), PowerNet™...
  • Page 34 Technical Specifications Feature Description WLAN Security: WEP, WPA Personal/Enterprise, WPA2 Personal/Enterprise, EAP-TLS, TTLS, LEAP, PEAP, Cisco CCX compliant (pending) WPAN (optional): Bluetooth class 2, version 1.2 (optional feature) Co-Located/ Two radios: WLAN/WPAN Operational: Physical Operating Temperature: Standard configuration: 14°–122°F / -10°–50°C nominal; -4° (-20°C) with reduced runtime Optional Bluetooth configuration: 32°–104°F / 0°–40°C •...
  • Page 35: Chapter 4 - Using The Keyboards

    Using the Keyboards Overview The keyboard buttons are recessed under the overlay for maximum durability. The keyboard panel is backlit for maximum viewability in various lighting conditions. There are two keyboard options: 24-Key Keyboard (see page 4-4) BKSP ALPHA / \ _ START PQRS –...
  • Page 36: Using The Function Keys

    Moves the cursor to the next tab stop or field (on a form or application window). Note: There is no SCAN key on the Dolphin 7850 terminal keyboard; scanning is initiated with the (page 3-6).
  • Page 37: Using The Navigation Keys

    Using the Navigation Keys Located in the center of each keyboard for easy access with either hand, the navigation keys enable you to navigate the cursor through an application screen. Press To … Move the cursor up one row or line. Move the cursor down one row or line.
  • Page 38: 24-key Keyboard

    24-Key Keyboard Alpha Lock Modifier keys Power Backlight key Toggling Between Alpha and Numeric Modes The 24-key keyboard defaults to numeric mode. Numeric mode is when you type numbers with the number keys. • Double-tap the Blue modifier key to toggle between alpha and numeric modes. •...
  • Page 39: 24-key Keyboard Numeric Key Combinations

    24-Key Keyboard Numeric Key Combinations Blue Mode Delete *Toggle Upper/Lower/Shift Blue ***Toggle Num/Alpha Red Mode; see 24-Key Keyboard Alpha Key Combinations Asterisk Start menu Light Suspend Left Volume up Down Volume down Right Insert Backtab Period - ; : Comma @ ? ! + [ ] pqrs or PQRS...
  • Page 40: 24-key Keyboard Alpha Key Combinations

    24-Key Keyboard Alpha Key Combinations Red Mode Alpha Base *Toggle Upper/ *Toggle Upper/ Lower/Shift Lower/Shift Blue ***Toggle Num/ Alpha Red Mode Asterisk Light Keyboard Light Keyboard Light Left Backspace Left Page Up Down Page Down Down Right Space Right Period - ;...
  • Page 41: 38-key Keyboard

    38-Key Keyboard Modifier keys Alpha Lock Power Backlight key Toggling Between Numeric and Alpha Modes The 38-key keyboard defaults to numeric mode. Numeric mode is when you type numbers with the number keys. Alpha mode is when you type the letter indicated on the overlay when you press the number key.
  • Page 42: 38-key Keyboard Alpha Key Combinations

    38-Key Keyboard Alpha Key Combinations Blue Mode Alpha Base Delete *Toggle Upper/ *Toggle Upper/ Lower/Shift Lower/Shift Blue Blue Mode Red Mode ALPH Start Num Mode Light Suspend Keyboard Light Left Left Volume up Down Volume down Down Right Insert Right Backtab Period Comma...
  • Page 43 38-Key Keyboard Alpha Key Combinations Blue Mode Alpha Base *Toggle Upper/Lower only on a double-tap. **Single-tap of SFT key changes shift mode for just the next character. Double-tap of SFT key toggles Caplock. ***Single tap of BLUE key changes mode for just the next character. Double tap toggles Num/Alpha. Dolphin®...
  • Page 44: 38-key Keyboard Numeric Key Combinations

    38-Key Keyboard Numeric Key Combinations Blue Mode Delete *Toggle Upper/Lower/Shift Blue ALPH Start Light Suspend Left Volume up Down Volume down Right Insert Backtab Period Comma 4 - 10 Num Mode Num Shift *Toggle Upper/Lower/Shift *Toggle Upper/Lower/Shift Blue Mode Blue Mode Red Mode Red Mode Alpha Mode...
  • Page 45 38-Key Keyboard Numeric Key Combinations Blue Mode *Toggle Upper/Lower only on a double-tap. Dolphin® 7850 Mobile Computer User’s Guide Num Mode Num Shift Rev C 4/30/2008 4 - 11...
  • Page 46 4 - 12 Rev C Dolphin® 7850 Mobile Computer 4/30/2008 User’s Guide...
  • Page 47: Chapter 5 - Using The Imager Scanner Engine

    Using the Imager Scanner Engine Overview The Dolphin terminal houses a compact imager scanner engine that uses Adaptus 5.0 which instantly reads all popular 1D and 2D bar codes and supports omni-directional aiming and decoding. This engine can also capture digital images, such as signatures and pictures of damaged inventory.
  • Page 48: Available Laser Engines

    Available Laser Engines In the future, you will be able to select one of the following laser engines for the Dolphin 7850 terminals: High Performance (HP) 5 mil Working Range: Near 2.75 in (0.07 m) 7 in (0.17 m) Long Range (LR)
  • Page 49: Supported Bar Code Symbologies

    Supported Bar Code Symbologies Symbology Type Symbology Name 1D Symbologies Codabar Code 3 of 9 Code 11 Code 32 Pharmaceutical (PARAF) Code 93 Code 128 EAN with Add-On EAN with Extended Coupon Code EAN-8 EAN-13 GS1-128 GS1 Databar Interleaved 2 or 5 2D Symbologies Aztec Codablock...
  • Page 50: Activating The Engine

    • Select Image Demo to verify imaging, or • Select Scan Demo to verify decoding. For more information about Demos, refer to the Dolphin Demos User’s Guide, which is available for download from www.honeywell.com/aidc. LEDs The LEDs in the center of both keyboards (for location, see engine.
  • Page 51: Decoding

    Decoding The Dolphin terminal supports two types of image decoding: full-area imaging and Advanced Linear Decoding (ALD). Full-area Imaging Full-area imaging means that the Dolphin terminal support omni-directional aiming, which means that a positive read can be obtained from many positions. For details, see Directional Scanning Positions ALD provides fast reading of linear (1D) and stacked linear bar codes (e.g., PDF417).
  • Page 52 Omni-Directional Scanning Dolphin terminals support omni-directional scanning. In general, the aiming pattern or beam is smaller when the terminal is held closer to the bar code and larger when farther from the bar code. Symbologies with smaller bars or elements (mil size) should be read closer to the terminal whereas larger bars or elements (mil size) should be read farther from the terminal.
  • Page 53: Capturing Images

    Capturing Images The image-capture process is an intuitive, split-second operation for experienced users. By following basic guidelines, however, new users can easily develop their own technique and, with practice, quickly learn to adapt to different application environments. Image Preview When the imaging process is initiated, the screen displays a preview of the object. This is a live video image of what the imager is currently viewing and has a slightly degraded appearance compared to the captured image.
  • Page 54 5 - 8 Rev C Dolphin® 7850 Mobile Computer 4/30/2008 User’s Guide...
  • Page 55: Chapter 6 - System Settings

    System Settings Overview Customizable settings are available from the Start menu. Tap Start > Settings and the Settings screen opens displaying the Personal tab. Settings consists of three tabs: Personal, System, and Connections. Personal Tab Description Personal The Personal tab provides access to personal configuration programs. For details, see System The Systems tab provides action to programs that monitor and adjust major system...
  • Page 56: Personal Settings

    Personal Settings To access the Personal tab, go to Start > Settings. The screen opens displaying the Personal tab. Icon Description Buttons Programs hardware buttons to launch applications or execute commands. Input Customizes the SIP. For details. Lock Provides password protection for certain programs on the terminal. Menus Customizes what appears on the Start and New menus.
  • Page 57: Buttons

    4. Verify the button assignment by tapping the button on the keyboard. For more information about HotKeys, refer to the Dolphin Power Tools User’s Guide, which is available for download from www.honeywell.com/aidc. Changing Button Assignments 1. After HotKeys is enabled, tap Start > Settings > Personal tab > Buttons.
  • Page 58: Input Panel Options

    Commands The Assign a program list also contains the following commands: Command Description <Input Panel> Opens the soft input panel. <None> Nothing happens when the button is pressed. <OK/Close> Performs the same function as tapping OK on the screen. <Scroll Down> Scrolls down in the open application.
  • Page 59: Menus - Modifying The Start Menu

    Menus - Modifying the Start Menu You can add existing programs you use often, such as File Explorer, to the Start menu for faster access. You are not installing the program, just enabling the user to access the program from the Start menu. You can add a program to the Start Menu three ways: directly by using the Menus setting, or creating and pasting shortcuts in File Explorer on the terminal or the workstation (and using ActiveSync to transfer to the shortcut to the terminal).
  • Page 60 3. Navigate to the Windows folder and open the Start Menu folder (My Device > Windows > Start Menu), tap and hold a blank area of the window, and tap Paste Shortcut on the pop-up menu. 4. The shortcut is now in the folder. 5.
  • Page 61: System Settings

    Version Tab Displays the information about the software, operating system, and processor of the terminal. The processor for the Dolphin 7850 terminal is an Intel XScale PXA 270 520MHz processor. Device ID Tab Displays the information the terminal uses to identify itself to other devices. It is important to know this information to identify the terminal when connecting to the network.
  • Page 62: Backlight

    Backlight The backlight for the color display is user-defined. Tap Start > Settings > System tab > Backlight.There are two tabs: Battery and External; the options on each tab are the same. The Battery tab determines display backlight settings when the terminal is running on battery power. The External tab determines display backlight settings when the terminal is powered by an external source, such as a charge cable.
  • Page 63 Certificates Certificates shows you the network certificates recognized by the operating system. There are personal and root certificates; each has its own tab. It is important to verify that the operating system acknowledges your certificate. If the certificate does not appear on one of these tabs, the operating system does see it, and it will not function properly during the network authentication process.
  • Page 64: Memory

    3-15. Volatile memory is used for running and storing programs as well as storing program data and is also known as RAM memory. The Dolphin 7850 terminal has 64MB of volatile memory by default. Non-Volatile Data stored in non-volatile Flash memory does persist through cold boots. The Dolphin 7850 terminal can have 64MB or 128MB of non-volatile memory depending in your configuration.
  • Page 65 Storage Card Tab This tab displays the current capacity and usage statistics of the selected memory type: IPSM or Storage Card. Select the memory type from the drop-down list. IPSM is selected by default. Field Total storage card… In use Free Drop-down list Running Programs Tab...
  • Page 66: Power

    Find Link Find searches for large files using storage memory. Clicking Find opens the Search program with Larger than 64KB already selected in the Type field. Enter the search criteria and tap Search. Power Battery Tab For more information about the terminal’s batteries, Advanced Tab Determines the amount of time that elapses before the terminal automatically goes into suspend mode;...
  • Page 67 Regional Settings Regional Settings enables you to customize the appearance and formatting to your geographic region. Specifically, you can customize numbers (i.e., number of decimal places allowed), currency (i.e.,using the $ or € € symbol), time, and date. These specifications apply to all screens, including the Today screen. The Region tab displays an overview of the region selected in the drop-down list at the top.
  • Page 68: Remove Programs

    Remove Programs The Remove Programs settings enables you to remove programs installed on the terminal. Use this setting to troubleshoot when you receive messages that the device is out of memory. The programs removed in the Remove Programs setting are removed from volatile memory. 1.
  • Page 69: Screen

    Screen Note: By default, dynamic screen rotation (i.e., the ability to switch between landscape and portrait orientation) is disabled on Dolphin 7850 terminals. Alignment Tab Tap Align Screen to re-align the screen. Remember, you first align the screen at bootup. You would need to re-align the screen again if tapping buttons or icons with the stylus no longer seems to work appropriately.
  • Page 70 This is the default font size setting. To change the font size, move the slider toward Smallest or Largest. The Example text changes to reflect the font change. Tap OK to save the new font size setting. Default Font Size Largest Font Size 6 - 16 Rev C...
  • Page 71: Chapter 7 - Communication

    For more information about communicating via the IrDA port, see Communication Wireless Radios Dolphin 7850 terminals can be equipped with a WLAN and/or Bluetooth radio. When the terminal’s radios are enabled, you can connect the terminal to a wireless network for communication.
  • Page 72: Default Com Port Assignments

    Bluetooth. Installing Additional Software Dolphin terminals ship with the operating system, radio drivers, and custom Honeywell software loaded onto the device. These are the default programs that install when your terminal first boots up. You can install additional software programs to the terminal provided that the following parameters are met: •...
  • Page 73: Using Activesync

    HomeBase device or a charge/communication cable. Hardware Requirements • Dolphin HomeBase device or Dolphin communication cable: USB or RS-232 • Power Adapter Cable from Honeywell Software Requirements To synchronize, ActiveSync 4.1 or higher must be installed and configured for the appropriate communication type on the host workstation and the Dolphin terminal.
  • Page 74: Adding Programs Via Activesync

    Honeywell, such as the charge/communication cable. Use of any peripheral not sold/manufactured by Honeywell may cause damage not covered by the warranty. You need to connect the Dolphin peripheral to the host workstation, then connect the Dolphin terminal to the peripheral.
  • Page 75 1. Download the program to the workstation from either the Internet or the installation CD. You may see a single *.exe or setup.exe file, a *.cab file, or *.dll. (There may also be several versions of files for different device types and processors.) 2.
  • Page 76: Connections Tab

    Connections Tab The Connections Tab of Windows Mobile Settings provides access to the configuration settings for many of the terminal’s communication options. Tap Start > Settings > Connections tab. Note: The programs that appear on the Connections tab depend on the terminal’s radio configuration. Program Icon Description...
  • Page 77: Connecting The Terminal To A Wireless Network

    2. Enter the appropriate configuration settings for each radio installed. Each radio has its own configuration program. • For details about configuring the WLAN radio, refer to the Honeywell WLAN Security Supplement User’s Guide, which is available for download from www.honeywell.com/aidc.
  • Page 78: Using Infrared Communication

    Using Infrared Communication The IrDA port sends and receives data between the terminal and other devices equipped with infrared. The maximum data transfer speed is 115 Kbps with a duty cycle of 18.75%. IrDA Port Location Verify Beam Settings By default, the IrDA port is enabled after each hard reset. This means that the IrDA port is ready to send and receive data via infrared.
  • Page 79 3. Tap and hold the item and select Beam File. 4. The information begins transmitting to the other infrared device. Receiving Data 1. Verify that the terminal is set to receive all incoming beams; see 2. Align the IrDA ports. 3.
  • Page 80: Connections Manager

    Connections Manager The connections manager sets up various network connections to Internet Service Providers (ISPs) via an external modem. If you are using one of the on-board wireless radios to connect to a network, do not enter network parameters in the connections manager. The Dolphin terminal uses the radio’s settings to connect to the network.
  • Page 81 Proxy Server Connections If you are connected to your ISP or private network during synchronization, the terminal should download the proper proxy settings during synchronization with the workstation. If these settings are not on your workstation or need to be changed, ask your ISP or network administrator for the proxy sever name, server type, port, type of Socks protocol used, and your user name and password.
  • Page 82: Network Cards

    Network Cards The Connections tab (see Connections Tab displays the network cards installed in the terminal. 1. Tap Start > Settings > Connections > Network Cards 2. Tap on an adapter in the list to review its settings. (Server-assigned IP addresses use DHCP.) 3.
  • Page 83: Radio Manager

    If the radio is disabled, the terminal doesn’t connect. Dolphin 7850 terminals can be configured with a WLAN and/or Bluetooth radio. Radio Driver Installation For a radio to show up in the Radio Manager, both the hardware module and the software driver for each radio must be installed in the terminal.
  • Page 84 Radio Manager Window Field Description Radio Modes Displays the radio hardware modules currently installed on the terminal. Status Field Provides feedback on the state of the radio. The Status field reads “Ready” when the selected radio is enabled and the Radio Manager is ready to receive a command. Otherwise, the Status field displays the following messages when enabling a radio: •...
  • Page 85: Usb To Pc

    The USB to PC applet enables you to switch between RNDIS (Remote Network Driver Interface Specification) USB and Serial USB communication. Dolphin 7850 terminals default to Serial USB. Honeywell recommends using Serial USB. To change this setting, tap Start > Settings > Connections tab > USB to PC is not selected, which indicates Serial USB.
  • Page 86 7 - 16 Rev C Dolphin® 7850 Mobile Computer 4/30/2008 User’s Guide...
  • Page 87: Chapter 8 - Wireless Pan Communication With Bluetooth

    Wireless PAN Communication with Bluetooth Bluetooth Radio The on-board Bluetooth radio is enabled by default at startup and operates within the 2.4 GHz–2.48 GHz band. Bluetooth transmissions hop between 79 separate frequencies 1,600 times every second, and with a communication range of about 10 meters (class II). Enabling the Bluetooth Radio The Bluetooth radio must be enabled in order to connect to other devices.
  • Page 88: Accessing Btexplorer

    Accessing BTExplorer When the Bluetooth radio is enabled, the Bluetooth icon on the Today screen appears as follows Tapping this icon once opens BTExplorer to the Favorites window. Note: When the Bluetooth radio is disabled, tapping this icon opens a warning message, which states that the radio is not enabled and to go to the Radio Manager as described in Accessing BTExplorer on page 8-2.
  • Page 89: Using Btexplorer

    Using BTExplorer BTExplorer has a New Connection Wizard for each type of Bluetooth connection you want to make; see Connection Types on page 8-7. matching devices and services, and the connection wizard walks you through the connection process. Different connection types will require different information. Make sure you have all the necessary information (PIN numbers, passkeys, MAC addresses, etc.) from the devices you want to connect to.
  • Page 90 4. Click Next and BTExplorer scans for other Bluetooth devices in range and displays the search results. 5. Select a device and click Next. BTExplorer attempts to connect to the selected device and explore the device’s available services. 6. Select a service in the list and tap Next. The next window enables you to save the device connection and service as a Favorite.
  • Page 91 b. Review the contents of the window and tap Next. The connection summary appears. 7. Tap Connect. If you are transferring files, the next steps are to select the file(s) and transfer them to the device. 8. While the terminal is transferring data, the icon on the Today screen will display a green, double- sided arrow over the Bluetooth icon 9.
  • Page 92 Favorites BTExplorer enables you to save connections to specific devices and the services on those devices as Favorites. Each time you try to connect to a device and service manually, you are asked if you want to save the connection as a Favorite. You can even give each connection a unique name. Favorite connections appear on the opening window each time you open BTExplorer.
  • Page 93: Connection Types

    Connection Types Connection Type Allows the Bluetooth radio to… Explore Services on Discover available services. Remote Devices Pair with Remote Pair with remote devices. Device ActiveSync via Synchronize files and data with a remote workstation via Bluetooth ActiveSync. Bluetooth Browse Files on See files on a remote device.
  • Page 94: Device Types

    Device Types BTExplorer supports the following device types: • Audio Devices • Network Devices • Phones • Printers • Computers • OBEX Devices By default, BTExplorer scans for Network Devices. To change the, device type, tap on the arrow to the right of the heading on the left. The name of this heading changes depending on what device type is selected;...
  • Page 95: Menu Options

    Menu Options The discovered devices window has a popup menu that enables you to perform several tasks. You can select a device and tap and hold or just tap and hold on an empty space; he same menu appears. Certain menu items are enabled or disabled depending on which method you use.
  • Page 96: Discovered Devices

    Discovered Devices In order for the terminal to find a device when scanning, that device must be Discoverable by Bluetooth. If not, the terminal won’t find the device when scanning. Furthermore, the device must have activated Bluetooth services. The terminal will retrieve only discoverable devices and the services activated on that device.
  • Page 97 2. Set Discoverable Mode to Discoverable. Set Connectable Mode to Connectable. You must change both for the terminal to be discoverable. 3. To activate specific services, tap the Services tab and tap Add. 4. Select a service and tap OK to add. Dolphin®...
  • Page 98 5. Each service you select is going to take you through a series of windows to confirm the parameters of the service. For example, for the file transfer service, the following window appears: 6. Tap OK and you are returned to the prior window, which now displays the service as active. 7.
  • Page 99: Pairing

    Pairing Pairing associates Bluetooth devices with each other so that you don’t have to enter access information every time a connection is requested. Bluetooth devices need to be paired with each other before attempting a connection the first time. Paired devices remain paired, even if: •...
  • Page 100 8 - 14 Rev C Dolphin® 7850 Mobile Computer 4/30/2008 User’s Guide...
  • Page 101: Chapter 9 - Dolphin Homebase Device

    7.4 volts DC required by the terminal. Use only the Li-ion battery packs provided by Honeywell. Use of any battery not sold/manufactured by Honeywell may result in damage not covered by the warranty.
  • Page 102: Front Panel

    Front Panel AUX Battery LED Indicates status of the battery charging in the auxiliary battery well; see page 9-3. Orange The auxiliary battery is charging. Green The auxiliary battery has completed charging and is ready for use. COMM LED The COMM LED indicates the status of data transfer between the Dolphin terminal and the host workstation.
  • Page 103: Back Panel

    The curve on the back wall of the terminal well accommodates the pistol-grip handle when the terminal is seated in the well. RS-232 Port For RS-232 data communication, use the 9-pin, RS-232 cable from Honeywell to connect this port to a peripheral device. For more information, see USB Port This USB Port is full-speed, 2.0 compliant, and requires ActiveSync 4.1 or higher.
  • Page 104: Bottom Panel Dimensions

    2. Snap the battery into place with a hinging motion. The Aux Battery LED lights orange. 3. The AUX Battery LED monitors the charge progress. Bottom Panel Dimensions 136.3 mm. (5.37 in.) 9 - 4 162.2 mm. (6.4 in.) 106 mm. (4.2 in.) 78 mm.
  • Page 105: Powering The Homebase Device

    ActiveSync communication (see Communication on page 9-8). Honeywell recommends that you leave the HomeBase device connected to its power source at all times, so that it is always ready to use. Dolphin® 7850 Mobile Computer User’s Guide...
  • Page 106 RS-232 Serial Connector The following diagram displays the pins of the RS-232 serial connector of the Back Panel (see page 9-3): Note: Signals referenced are for a DTE device. The HomeBase device is at a right-angle to the printed circuit board (PCB).
  • Page 107: Charging The Main Battery

    Charging the Main Battery The HomeBase device powers the terminal and fully charges its main battery pack in less than four(4) hours. To check battery power, see As battery packs charge, the charging circuitry follows the two-step charging process (CC-CV) that is recommended for Li-ion batteries.
  • Page 108: Activesync Communication

    The DOCK LED lights green. If not, make sure that the terminal is properly seated. You may need to remove and re-insert the terminal. • The terminal activates. If not, verify that the Honeywell power supply is properly connected to the Power Jack (see page 9-3) on the back panel and plugged into a functioning outlet.
  • Page 109: Rs-232 Cables

    RS-232 Cables Connect the HomeBase device to the host workstation or other device by plugging an RS-232 serial cable into the RS-232 Port (see page 9-3) on the back panel. The wiring of your cable depends on whether the other device is set up as a Data Communication Equipment (DCE) or Data Terminal Equipment (DTE) device.
  • Page 110: Mounting The Dolphin Homebase Device

    Mounting the Dolphin HomeBase Device Set the HomeBase device on a dry, stable surface, such as a desktop or workbench near an electrical outlet. Be sure to provide enough workspace with good lighting for the user to view and operate the terminal while it is seated in the HomeBase device.
  • Page 111 Wall Mounting A wall mount kit that contains a screws and a mounting bracket can be purchased separately. The bottom panel of the HomeBase device contains four(4) rubber feet–one at each corner–that help keep it stable and secure when resting on a flat surface. Those rubber feet should be removed with pliers before wall mounting the HomeBase device.
  • Page 112 9 - 12 Rev C Dolphin® 7850 Mobile Computer 4/30/2008 User’s Guide...
  • Page 113: Chapter 10 - Dolphin Quadcharger Device

    Li-ion batteries. The process monitors changes in temperature, current, and voltage. The charger also resets and calibrates battery pack data. Use only the Li-ion battery packs provided by Honeywell. Use of any battery not sold/manufactured by Honeywell may result in damage not covered by the warranty.
  • Page 114: Front Panel

    Front Panel Charging Slots–with batteries Status LEDs Charging Slots There are four(4) charging slots. Each slot holds one battery. When a battery is placed in a slot, it immediately begins charging. Charge/Analyze Slot This is the fourth slot and the only one that can be used to analyze a battery. When a battery is placed in this slot, it begins charging just as it does in the other three slots.
  • Page 115: Back Panel

    Back Panel Power Supply Connector Use this connector to attach the power supply to the QuadCharger device. The universal power supply accepts input voltages between 90-265 volts. Power Switch Toggle the power switch to turn the QuadCharger device on and off. Inserting and Removing Battery Packs To insert a battery pack, place the end of the battery without the locking tab into the bottom of the charging pocket and snap the battery into place with a hinging motion.
  • Page 116: Charging Batteries

    Charging Batteries For best results, battery packs should be at room temperature before recharging them because temperature impacts charging. The recommended temperature range is 50° to 95° F (10° to 35° C). 1. Supply the QuadCharger device with power and turn the power switch on. 2.
  • Page 117: Using The Battery Analyzer

    Using the Battery Analyzer The fourth charging slot is also the CHARGE/ANALYZE slot because, in addition to charging a Li-ion battery, this slot runs an Analyze cycle on the battery placed in it, which helps you monitor battery capacity over time. Analyze Button The Analyze cycle is initiated when a battery is placed in the Charge/Analyze slot and the Analyze button is pressed.
  • Page 118: Bottom Panel

    Bottom Panel DIN Rail Slot Mounting the QuadCharger Device The QuadCharger device should be on a dry, stable surface. To easily adapt the QuadCharger device to your environment, it can be mounted on a flat, horizontal surface such as a desktop or workbench, or a flat, vertical surface such as a wall.
  • Page 119: Troubleshooting

    Status LED lights red again, then the problem is associated with the battery pack. An error occurred during the self-diagnostic test for that particular charging pocket. Call Honeywell Product Service and request an RMA. For additional warranty and return information, see...
  • Page 120 10 - 8 Rev C Dolphin® 7850 Mobile Computer 4/30/2008 User’s Guide...
  • Page 121: Chapter 11 - Dolphin Chargebase

    Capacity The ChargeBase can hold up to four(4) Dolphin terminals. Use only the Li-ion battery packs provided by Honeywell. Use of any battery not sold/manufactured by Honeywell may result in damage not covered by the warranty. Use only the peripherals, power cables, and power adapters from Honeywell. Use of peripherals, cables, or power adapters not sold/manufactured by Honeywell may cause damage not covered by the warranty.
  • Page 122: Front Panel

    Front Panel Terminal Wells The ChargeBase contains four(4) terminals wells. Each terminal well • Holds and charges the main battery pack of one Dolphin terminal. • Contains the companion to the I/O connector on the bottom panel of Dolphin terminals. •...
  • Page 123: Back Panel

    Back Panel Power Supply Connector This connector receives input from the power adapter. Plug the power connector cable from the power adapter into this connector. There is no ON/OFF switch on the back panel of the ChargeBase. The ON/OFF switch is on the power adapter. Power Supply The ChargeBase includes a power supply that contains a power adapter to ensure the proper voltage.
  • Page 124: Supplying Power To The Chargebase

    Supplying Power to the ChargeBase Use only the peripherals, power cables, and power adapters from Honeywell. Use of peripherals, cables, or power adapters not sold/manufactured by Honeywell may cause damage not covered by the warranty. 1. Be sure the power switch on the power adapter is in the OFF position.
  • Page 125: Charging Terminals In The Chargebase

    Charging Terminals in the ChargeBase The ChargeBase charges the main battery of each terminal in less than four(4) hours. The intelligent battery charging system incorporated in the Dolphin terminal prevents overcharging, which means that Dolphin terminals may be stored in the ChargeBase indefinitely without damage to the terminals, battery packs, or the ChargeBase.
  • Page 126: Mounting The Chargebase

    Mounting the ChargeBase The ChargeBase should be placed on a dry, stable surface. To easily adapt the ChargeBase to your environment, it can be mounted on a flat, horizontal surface such as a desktop or workbench, or a flat, vertical surface such as a wall. When choosing a location, always bear in mind that •...
  • Page 127 3. Secure the DIN Rail to a stable, flat horizontal surface. Dolphin® 7850 Mobile Computer Rev C 11 - 7 4/30/2008 User’s Guide...
  • Page 128 Using the Mounting Brackets A wall mount kit can be purchased separately. It contains two mounting brackets to secure both ends of the ChargeBase. Use the screws and the mounting brackets to mount the ChargeBase to a wall or other vertical surface.
  • Page 129: Chapter 12 - Cables Kits

    Charge/Communication cable that connects the terminal to an external power source and a host workstation. Use only the peripherals, power cables, and power adapters from Honeywell. Use of peripherals, cables, or power adapters not sold/manufactured by Honeywell may cause damage not covered by the warranty.
  • Page 130: Using The Power Cable

    Using the Power Cable The Power Cable connects the terminal to an external power source via the DC jack on the bottom panel of the pistol-grip handle. DC Power Jack (Pull back the rubber flap to gain access to the power jack.) The Power Cable contains a power adapter that converts the voltage from the power source to 9.5 volts DC, which is the maximum voltage the terminal can receive.
  • Page 131: Using The Mobile Charger

    Using the Mobile Charger The Mobile Charger connects the terminal to a vehicle power source. This cable powers the terminal and charges the main battery pack. Terminal Connector Jackscrews Vehicle Power Adapter Using the Mobile Charger Inside a Vehicle Using the Mobile Charger in combination with the Mobile Mount powers and secures the terminal inside a vehicle.
  • Page 132: Using The Charge/comm Cable

    Using the Charge/Comm Cable The Charge/Comm cable charges the terminal and communicates with a host workstation. There are three connectors: one connects the terminal to an external power source, another to the host workstation, and another to the terminal itself. The charge/comm cable is actually two cables: a power cable and a communication cable.
  • Page 133 Using the Charge/Comm Cable 1. Plug the cable’s terminal connector into the I/O connector on the bottom panel of the terminal. 2. Tighten the jackscrews. 3. Plug the power cable connector into the power cable. 4. Plug the power adapter on the power cable into a standard power outlet. 5.
  • Page 134 12 - 6 Rev C Dolphin® 7850 Mobile Computer 4/30/2008 User’s Guide...
  • Page 135: Chapter 13 - Customer Support And Warranty

    +86 21 6361 3818 E-mail: aptechsupport@handheld.com Japan Telephone: +813 5770-6312 E-mail: aptechsupport@handheld.com Malaysia Telephone: +603-6201-7020 E-mail: aptechsupport@handheld.com Online Technical Assistance You can also access technical assistance online at www.honeywell.com/aidc. Dolphin® 7850 Mobile Computer User’s Guide Rev C 4/30/2008 13 - 1...
  • Page 136: Product Service And Repair

    Product Service and Repair Honeywell provides service for all its products through service centers throughout the world. To obtain warranty or non-warranty service, contact the appropriate location below to obtain a Return Material Authorization number (RMA #) before returning the product.
  • Page 137: Limited Warranty

    No product will be accepted by Honeywell without a Return Materials Authorization, which may be obtained by contacting Honeywell. In the event that the product is returned to Honeywell or its authorized service center within the Warranty Period and Honeywell determines to its satisfaction that the product is defective due to defects in materials or workmanship, Honeywell, at its sole option, will either repair or replace the product without charge, except for return shipping to Honeywell.
  • Page 138 How to Extend Your Warranty Honeywell offers a variety of service plans on our hardware products. These agreements offer continued coverage for your equipment after the initial warranty expires. For more information, contact your Sales Representative, Customer Account Representative, or Product Service Marketing Manager from Honeywell, or your Authorized Reseller.
  • Page 140 Honeywell 700 Visions Drive P.O. Box 208 Skaneateles Falls, NY 13153-0208 ™ 7850-UG Rev C 4/30/2008...

Comments to this Manuals

Symbols: 0
Latest comments: