Color Change - ADJ ULTRA HEX PAR3 User Instructions

POWER
Ultra Hex Par3 DMX512
DMX+,DMX-,COMMON
nect the cable's shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR's outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
1
DMX512 OUT
3
3-PIN XLR
2
XLR Male Socket
REMOTE
INPUT OUTPUT
1 Ground
CONTROL
2 Cold 2 Cold
INPUT
3 Hot
Figure 3
Special Note: Line Termination.
POWER
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con-
nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ Products, LLC part number Z-DMX/T) will decrease the possibili-
ties of erratic behavior.
Termination reduces signal errors and
avoids signal transmission problems
1 1
DMX512 IN
and interference. It is always advisable
3 3
3-PIN XLR
to connect a DMX terminal, (Resistance
2 2
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
5-Pin XLR DMX Connectors.
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
ADJ Products, LLC - www.adj.com - Ultra Hex Par3 User Manual Page 6
COMMON
DMX +
1
DMX512 IN
3
3-PIN XLR
DMX -
2
Figure 2
XLR Female Socket XLR Pin Configuration
REMOTE
INPUT OUTPUT
SOUND CONTROL
1 Ground
Pin 1 = Ground INPUT
Pin 2 = Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
When longer runs of cable are
Figure 4
Some manufactures use 5-pin DMX-
5-Pin XLR Male (In)
Pin 1 Pin 1
Pin 2 Pin 2
Pin 3 Pin 3
Do Not Use
Do Not Use
POWER
Set Up Ultra Hex Par3
Control Panel Lock:
The control panel will lock itself after 30 seconds if nothing is
pressed. To unlock the control panel, press the MODE button
for 3 seconds.
Termination reduces signal errors and
avoids signal transmission problems
1
and interference. It is always advisable
3
Operating Modes:
2 to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
The Ultra Hex Par3 has five operating modes:
and PIN 3 (DMX +) of the last fixture.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the ADJ Show Designer.
• RGBWA + UV Mode - Choose one of the six colors to remain static
or adjust the intensity of each color to make your own color.
• Sound-Active mode - The unit will react to sound, chasing through
the built in programs. There are 16 sound active modes.
POWER
• Auto Mode - There are 33 Auto Modes to choose from. 16 color
fade modes, 16 color change modes, and 1 random mode.
• Static Color Mode - There are 63 colors to choose from.
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs.
The Ultra Hex Par3 has 5 DMX modes: 6 Channel mode, 7 Channel
mode, 8 Channel mode, 11 Channel mode, and a 12 Channel mode.
See pages 14-22 for each modes' DMX traits.
1. This function will allow you to control each individual fixture's
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
"d.XXX" is displayed. "XXX" represents the current displayed ad-
dress. Use the UP or DOWN buttons to select your desired DMX
address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 6 Channel Mode, press the MODE button until "Ch06"
is displayed. This is the 6 Channel DMX Mode.
• To run the 7 Channel Mode, press the MODE button until "Ch07"
is displayed. This is the 7 Channel DMX Mode.
• To run the 8 Channel Mode, press the MODE button until "Ch08"
ADJ Products, LLC - www.adj.com - Ultra Hex Par3 User Manual Page 7
POWER
Operating Instructions