Pre-Position; Pan/Tilt; Auxiliary Ac Supply Output; Auxiliary - Bosch LTC 8561 Series Instruction Manual

LTC 8561 | Instruction Manual | Summary of PIN Assignments
7.3.1 J105 - Lens Output
Pin No. Signal Name
1 Zoom
2 Focus
3 Iris
4 Common
7.4

Pre-position

Pre-positions: 82 with 5 functions each (when using
continuous pan motor) or 99 with 4 functions each.
Five conductor terminal block, J111, and four
conductor terminal block, J106, are found on left side
of the top main printed circuit board. Pin one is to the
left side of the connectors.
7.4.1 J111 - P&T Position Sense
Pin No. Signal Name
1 +
2 PAN1
3 PAN2
4 TILT
5 –
7.4.2 J106 - Lens Position Sense
Pin No. Signal Name
1 +
2 ZOOM
3 FOCUS
4 –
7.5

Pan/Tilt

Pan/Tilt Output: 4 function for pan/tilt solid state
drive with zero crossing turn-on; 1 A drive capability.
Auto-pan/Auxiliary Output 1: Solid state drive with
zero crossing turn-on; 1 A drive capability.
Six conductor terminal block, J406, and two conductor
terminal block, J401, are found near the left hand side
of the lower printed circuit board. Pin one is to the left
side of connector.
Bosch Security Systems | January 19, 2006
Remarks
Connect to lens zoom motor wire.
Connect to lens focus motor wire.
Connect to lens iris motor wire.
Connect to lens motor common
wire.
Remarks
Connect to P/T motor pre-position
sensor power.
Connect to first P/T motor pan
pre-position sense.
Connect to second P/T motor pan
pre-position sense.
Connect to P/T motor tilt
pre-position sense.
Connect to P/T motor pre-position
sensor ground.
Remarks
Connect to lens motor pre-position
sensor power.
Connect to lens motor zoom pre-
position sense.
Connect to lens motor focus pre-
position sense.
Connect to lens motor pre-position
sensor ground.
7.5.1 J406 - P&T Output
Pin No. Signal Name
1 RIGHT
2 LEFT
3 UP
4 DOWN
5 AUTO-PAN
6 FIELD
7.5.2 J401 - P&T Common
Pin No. Signal Name
1 RETURN
2 RETURN
7.6

Auxiliary AC Supply Output

NOTE: For the LTC 8566/60 and LTC 8566/50, the
maximum total current output, including Pan/Tilt
Output, Auxiliary 1 Output, and Auxiliary Supply
Output, is 2 A.
Auxiliary AC Supply Output: Fuse-protected auxiliary
AC supply. See Power under DESCRIPTION.
Two conductor terminal block, J402, is found in the
middle of the lower printed circuit board. Pin one is to
the left side of the connectors.
7.6.1 J402 - Auxiliary AC Supply
Pin No. Signal Name
1 SUPPLY
2 RETURN
7.7

Auxiliary

Auxiliary Output 2, 3, and 4: relay contact rating 250
VAC, 5 A resistive, 0.25 hp.
Three conductor terminal blocks, J405, J407, and J408
are found on the right hand side of the lower printed
circuit board. Pin one is at the left side of the
connectors.
7.7.1 J405, J407, J408 - Auxiliary Relays
Pin No. Signal Name
1 NO
2 COMMON
3 NC
EN | 17
Remarks
Connect to pan right control wire.
Connect to pan left control wire.
Connect to tilt up control wire.
Connect to tilt down control wire.
Connect to auto-pan control wire.
No Connection.
Remarks
Connect to pan/tilt motor return
wire.
Connect to pan/tilt motor return
wire.
Remarks
Auxiliary AC supply terminal.
Auxiliary AC return terminal.
Remarks
Normally open contact.
Common contact.
Normally closed contact.