Download Print this page

Honda GX200 Owner's Manual: Oil Change; Air Cleaner; Inspection

Honda engine owner's manual.
Hide thumbs

Advertisement

6 : 1 Reduction Case
1.
Remove the oil-level-check bolt
and washer, and see whether the
oil level is at the edge of the bolt
hole.
2.
If the oil level is below the check
bolt hole, remove the filler bolt
and washer. Add oil until it starts
to flow out the check bolt hole
with the recommended oil (see
page
9
).
3.
Install the oil-level-check bolt,
filler bolt and washers. Tighten
them securely.

Oil Change

2 : 1 Reduction Case With Centrifugal Clutch
Drain the used oil while the engine is warm. Warm oil drains
quickly and completely.
1.
Place a suitable container below the reduction case to catch the
used oil, then remove the oil filler cap/dipstick, the drain plug
and washer.
2.
Allow the used oil to drain completely, then reinstall the drain
plug and a new washer, and tighten it securely.
Please dispose of used motor oil in a manner that is compatible
with the environment. We suggest you take used oil in a sealed
container to your local recycling center or service station for
reclamation. Do not throw it in the trash or pour it on the ground
or down a drain.
3.
With the engine in a level position, fill to the upper limit mark on
the dipstick with the recommended oil (see page
the oil level, insert and remove the dipstick without screwing it
into the filler hole.
Reduction case oil capacity:
Running the engine with a low reduction case oil level can cause
reduction case damage.
4.
Screw in the filler cap/dipstick securely.
UPPER
LIMIT
LOWER LIMIT
10
OIL LEVEL
FILLER BOLT
OIL-LEVEL-CHECK BOLT
9
). To check
0.50 (0.53 US qt , 0.44 Imp qt)
FILLER CAP/DIPSTICK
DRAIN PLUG
6 : 1 Reduction Case
Drain the used oil while the engine is warm. Warm oil drains
quickly and completely.
1.
Place a suitable container below the reduction case to catch the
used oil, then remove the filler bolt, oil-level-check bolt and
washers.
2.
Drain the used oil completely into the container by tipping the
engine toward the oil-level-check bolt hole.
Please dispose of used motor oil in a manner that is compatible
with the environment. We suggest you take used oil in a sealed
container to your local recycling center or service station for
reclamation. Do not throw it in the trash or pour it on the ground
or down a drain.
3.
With the engine in a level position, fill oil until it starts to flow
out the check bolt hole with the recommended oil (see page
Running the engine with a low reduction case oil level can cause
reduction case damage.
4.
Reinstall the oil-level-check bolt, filler bolt and new washers,
and tighten them securely.
OIL-LEVEL-CHECK BOLT
AIR CLEANER
A dirty air cleaner will restrict air flow to the carburetor, reducing
engine performance. If you operate the engine in very dusty areas,
clean the air filter more often than specified in the MAINTENANCE
SCHEDULE.
Operating the engine without an air filter, or with a damaged air
filter, will allow dirt to enter the engine, causing rapid engine wear.
This type of damage is not covered by the Distributor's Limited
Warranty.
Inspection
Remove the air cleaner cover and inspect the filter elements.
Clean or replace dirty filter elements. Always replace damaged
filter elements. If equipped with an oil-bath air cleaner, also check
the oil level.
Refer to pages
11
12
and filter for your engine type.
ENGLISH
FILLER BOLT
OIL LEVEL
for instructions that apply to the air cleaner
9
).

Advertisement

   Also See for Honda GX200

   Related Manuals for Honda GX200

This manual also for:

Gx120, Gx160

Comments to this Manuals

Symbols: 0
Latest comments:
  • Randy G Sep 01, 2014 06:18:
    I have no spark would it be the mag