Page 1
Website : http://www.LGEservice.com http://blz.lgservice.com E-mail : http://LGEservice.com/techsup.html DISHWASHER SERVICE MANUAL NOTE BEFORE SERVICING THE UNIT, PLEASE READ THIS MANUAL CAREFULLY FOR SAFETY AND CORRECT SERVICES. Model : LD-1426T LD-1416T LD-1415M LD-1403W LD-1204W/LD-1204M...
CAUTION ! DISCONNECT POWER CORD BEFORE SERVICING RECONNECT ALL GROUNDING DEVICES IMPORTANT SAFETY NOTICE ! This service information is intended for individuals possessing adequate backgrounds of electrical, electronic and mechanical experience. Any attempt to repair this appliance may result in personal injury and property damage.
2. SPECIFICATION ITEM SPECIFICATION Model LD-1426T LD-1416T LD-1415M LD-1403W LD-1204W/M Rated Voltage / Frequency AC 240V/50Hz Installation Free Standing Place Settings Product Dimension(mm) 600(W) 600(D) 850(H) Product Weight(Kg) Stainless Stainless White Door Color Titanium White Steel Steel / Titanium Stainless Steel...
3. PARTS NAME LD-1426T LD-1416T/1415M LD-1403W/1204W/1204M The racks are different each other by model 1. Control Panel 10. Adjust Leg 2. Door Handle(with Handle Deco) 11. Upper Rack 3. Front Cover 12. Cutlery Basket 4. Lower Cover 13. Detergent & Rinse Aid Dispenser 5.
This is how Rinse course can eliminate some bacteria such as salmonella. Extra Hot Model Temperature LD-1426T 77°C LD-1403W LD-1204W/M 4-1-2. Turbo Spray System LD-1416T 80°C LD-1415M • Turbo Spray System is elaborately designed to achieve a more powerful and efficient wash.
4-2 Display Panel 4-2-1. LD-1426T CHILD SPRAY PROGRAM TIME DELAY LOCK INTENSITY • Used to lock or • When you want to • With each press, the • If you want to delay the start unlock the select program, press...
4-2-2. LD-1416T TRIPLE INDICATOR TIME LEFT DELAY START SPRAY • Before starting, the display window shows the running time of • Refill with • If you want to delay the • With each press, the level the selected program. of water jet is changed to rinse aid start of selected program, •...
Page 10
4-2-3. LD-1415M INDICATOR TIME LEFT DELAY START • Before starting, the display window shows the running time of • Refill with • If you want to delay the the selected program. rinse aid start of selected program, • After starting, the display window shows the remaining time. press this button before •...
4-2-4. LD-1403W DELAY START POWER SWITCH TIME SAVE HALF LOAD BUTTON BUTTON • If you want to delay the • This function is for • In case of small load, use upper or • For operating, press this start of selected program, saving time and energy.
Page 12
4-2-5. LD-1204W/1204M DELAY START POWER SWITCH REMAINING TIME HALF LOAD BUTTON BUTTON • If you want to delay the • In case of small load, use upper or • Indication of remaining • For operating, press this start of selected program, lower rack only to save energy.
Page 13
4-3 TEST MODE 4-3-1. LD-1426T CHECK PROGRAM(START IN THE STATE OF THE CLOSED DOOR) The number of BUTTON DISPLAY Load and Checking points DOOR pushing button “ ” “ ” “ ” “ ” “ ” - 13 -...
Page 14
4-3-2. LD-1416T/1415M CHECK PROGRAM(START IN THE STATE OF THE CLOSED DOOR) The number of BUTTON DISPLAY Load and Checking points DOOR pushing button Micro S/W must be ON to operate HEATER CHECK MODE ※ BUTTON OPERATION - 14 -...
Page 15
4-3-3. LD-1403W CHECK PROGRAM(START IN THE STATE OF THE CLOSED DOOR) The number of BUTTON DISPLAY Load and Checking points DOOR pushing button Micro S/W must be ON to operate HEATER CHECK MODE ※ BUTTON OPERATION - 15 - - 15 -...
Page 16
4-3-4. LD-1204W/1204M CHECK PROGRAM(START IN THE STATE OF THE CLOSED DOOR) The number of BUTTON DISPLAY Load and Checking points DOOR pushing button Micro S/W must be ON to operate HEATER CHECK MODE ※ BUTTON OPERATION - 16 -...
7. HOW TO DISASSEMBLE BEFORE DISASSEMBLING THE DISHWASHER ; 1) Remove the plug from electric outlet to avoid electric shock. 2) Close the Water Tap(faucet). 3) Remove all dishes and items in the dishwasher. 4) Remove the Lower Rack and the Upper Rack. 5) In case of the water softner assembly model, open the water softner cap to flow out the water to sump and drain to avoid the floor wet.
4. Balance weight 1) Remove side 4 screws. 2) Lift the balance weight. 5. Door Assembly LD-1426T 1) Front Cover Open the door. Remove 4 screws(long Type, stainless). Remove 6 screws(stainless). Close the door slowly and remove front cover downwards.
Page 26
LD-1416T/1415M 1) Front Cover Open the door. Remove 6 screws(stainless). Close the door slowly and remove front cover downwards. 2) Control Panel Assembly Open the door. Remove 8 screws(stainless). Main Display Part Option Display Part Remove wire connection. Latch Assembly Be sure the wiring should not be changed in reassembling.
Page 27
Remove the air duct. Cover Remove the wire connections. LD-1415M Detergent Remove the outer cover by removing 1 1416T Dispenser LD-1426T screw. Remove 2 fixing screws inside and turn the Inner Cover counterclockwise. Inner Cover Door Liner 4) Detergent Dispenser Close the door.
6. Base spacer Remove 4 screws. Lift the front side of dishwasher and pull the base spacer forward. 7. Tub assembly 1) Nozzle Pull up the nozzle. 2) Filter Assembly Inner filter Turn inner filter counterclockwise and lift inner filter and middle filter. Middle filter You can disassemble inner filter and Micro filter...
Page 29
1) Remove the screw which tighten washing motor and base. 2) Lift them upward. Be careful not to wet the floor by the water left in the sump. LD-1426T LD-1416T 3) Pull out the float switch with pressing LD-1415M downward softly.(not on all models)
Page 30
7) Vario valve Remove 4 screws and lift the cover upward. Lift the vario valve upward. 8) Capacitor Remove 1 screw. LD-1426T/1416T 9) Noise filter Remove 1 screw. 10) Power cord assembly Turn the power cord assembly 90º and take it off.
Page 31
LD-1426T/1416T/1415M 11) Aquastop Press the holder hook as shown in figure. Pull the hose assembly. LD-1403W/1204W/1204M 12) Inlet valve Remove 2 screws. 13) Drain Hose Press the rear side hook. Pull the holder forward. Pull the holder upward. - 31 -...
Page 32
7-2. DISASSEMBLE C-BASE ASSEMBLY Be careful not to be injured by the sharp edge of tub. 1. Top Plate See 7-1. 1. 2. Low Cover See 7-1. 2. 3. Cabinet-R/L See 7-1. 3. 4. Air Guide Disconnect 3 hoses assembly. You need not to unscrew the air guide nut.
Page 33
(You can’t lift up base perfectly because of some parts connecting to base.) 7. Disconnect the connecting points between tub and base 1) Disconnect noise filter. (LD-1426T/1416T/1415M) 2) Disconnect of powercord assembly. 3) Disconnect wire from the capacitor. - 33 - - 33 -...
Page 34
4) Disconnect wire from the inlet valve or Aquastop Now, you can remove the base from the tub perfectly. 8. C-Base Assembly You can repair the parts in the C-Base like heater case, washing pump, drain motor etc. - 34 - - 34 -...
8.TROUBLE SHOOTING METHODS A. TROUBLE SHOOTING ACCORDING TO DISPLAYED ERROR MESSAGE POSSIBLE CAUSE ERROR MESSAGE REMEDY FOR ERROR OCCURRENCE The Water Tap is not opened. Open the Water Tap. INLET ERROR The Inlet Hose is kinked. Repair the Inlet Hose. The Filter of inlet valve clogged a) Close the Water Tap.
Page 36
The water is not heated or the temperature in the Tub is overheated to over 95¡C This process is not part of the LD-1426T COOL DRY program. At this time, the fan will LD-1416T operate for a few more minutes to LD-1415M diminish any remaining moisture.
B. TROUBLE DIAGNOSES AND REPAIR BY SYMPTOM No Power on when the power button pressed. • Insert the Plug Correctly. The plug is correctly inserted in the • Check the electricity is failed or not. Socket-Outlet? The Fuse or • Replace the Fuse or Circuit Breaker of house. Circuit Breaker of house is O.K? The Thermal Fuse...
Page 38
The Wash Pump/Motor does not run. • Close the Door Tightly. The Door is tightly • Check the Door Switch in Latch Handle. closed? The Pump/Motor is • Remove the cause of block or replace the Pump/Motor. not blocked? The circuit of Pump/ •...
Page 39
Washing Results are not Satisfactory After washing, are there still Reduce the amount of Rinse-Aid White deposits or streaks on (for Streak) the dishes? After washing, are there still food soils on the dishes? Check that : - the amount of detergent Correctly used or not - Filters clogged or not.
Page 40
Power Button not automatically off after operation. Check the button is blocked by foreign materials. Check the Power Switch.(Replace it, if necessary.) Check the Controller.(Replace it, if necessary.) - 40 - - 40 -...
9. INSTALLATION INSTRUCTION Step1: Prepare Cupboard opening 1. This dishwasher is designed to fit to the size shown as below. 2. Select a location as close to sink as possible for easy connections to water and drain lines. 3. The dishwasher should not be installed more than 3 meters from sink for proper drainage. 4.
Page 42
Step 2 : PREPARE ELECTRICAL WIRING CAUTION For personal safety, remove house fuse or open circuit breaker before installation. Do not use an extension cord or adapter plug with this appliance. Electrical and grounding connections must comply with the national electrical code/provincial and municipal code and/or other local codes.
Page 43
Step 5 : DRAIN LINE CONNECTION 1. If the end drain hose does not fit to the drain line, use a piece of rubber connector (not supplied) that must be resistant to heat and detergent and may be obtained from a plumbing shop. 2.
Page 44
Drain Hose Extension Drain Hose extension kits are available from through your local service centre. Extend drain Hose as shown below. (Refer to Fig. C) Fig. C 200 mm Max. Sink Fig. D Copper pipe fl 20mm flared at drain nose and other end if required.
10. EXPLODED VIEW LD-1204W/M LD-1403W LD-1426T LD-1416T LD-1415M The appearance and specifications may be varied without notice according to localities. - 45 - - 45 -...
Run_Date : 2006-01-01 SPECIFICATION : 240V 50Hz LD-4263T LD-4163T LD-4152M LD-4031W LD-2040W Your Model Your Model Your Model Your Model Your Model DESC LD-1426T LD-1416T LD-1415M LD-1403W LD-1204W *001 Manual Assembly, Owners 3829DD3005K 3829DD3005B 3829DD3005C 3829DD3005P 3829DD3005L *002 Box, Carton...