Hitachi C 6SS Technical Data And Service Manual
  1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Saw
  5. C 7SS
  6. Technical data and service manual
Hitachi C 6SS Technical Data And Service Manual

Hitachi C 6SS Technical Data And Service Manual

Circular saw
Hide thumbs Also See for C 6SS:
Table of Contents

Advertisement

Quick Links

PRODUCT NAME
Hitachi Circular Saw
Models
165 mm (6-1/2")
190 mm (7-1/2")
MARKETING OBJECTIVE
Although our C 6MFA/C 7MFA Circular Saws now available on the European market are highly evaluated as
reasonably priced, light-load products, there is also growing demand for less expensive and lighter circular saw
products. In order to expand the market share of our circular saw series products, we consequently released the
C 6SS/C 7SS Circular Saws in wider regions including Europe, as a low-priced series developed by balancing
price and performance.
APPLICATIONS
• Cutting of various wood materials
SELLING POINTS
[ NEW FEATURES ]
Compact and lightweight design
Power-plus heavy-duty motor
Sawdust rear-discharge type
(Dust collector installable)
Blower function
[ SAME FEATURES AS THE CONVENTIONAL MODELS ]
Accurate and sturdy aluminum die-cast base
(Steel plate base available depending on
destination)
Double-insulated construction
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.
C 6SS
C 7SS
LIST No.
C 6SS: E519
C 7SS: E520
Jun. 2009
Sales Division
C

Advertisement

Table of Contents
loading

Related Manuals for Hitachi C 6SS

Summary of Contents for Hitachi C 6SS

  • Page 1 In order to expand the market share of our circular saw series products, we consequently released the C 6SS/C 7SS Circular Saws in wider regions including Europe, as a low-priced series developed by balancing price and performance.
  • Page 2 REMARK: • For more information about HANDLING INSTRUCTIONS, visit our website at: http://www.hitachi-koki.com/manual_view_export/ • Throughout this TECHNICAL DATA AND SERVICE MANUAL, a symbol (s) is (are) used in the place of company name (s) and model name (s) of our competitor (s). The symbol (s) utilized here is (are) as...

  • Page 3: Table Of Contents

    PRECAUTIONS ON SALES PROMOTION ----------------------------------------------------------------------------- 5 1. Safety Instructions ---------------------------------------------------------------------------------------------- 5 REPAIR GUIDE ----------------------------------------------------------------------------------------------------------------- 6 1. Precautions on Disassembly and Reassembly ---------------------------------------------------------- 6 STANDARD REPAIR TIME (UNIT) SCHEDULES ------------------------------------------------------------------- 13 Assembly Diagram for C 6SS Assembly Diagram for C 7SS...

  • Page 4: Selling Points

    Blower function The Models C 6SS and C 7SS come with the blower function to blow sawdust away using cooling air of the motor. Accurate and sturdy aluminum die-cast base...

  • Page 5: Specifications

    SPECIFICATIONS 1. Specifications Model C 6SS C 7SS Saw blade diameter 165 mm (6-1/2") 190 mm (7-1/2") at 90° 0 to 57 mm (0 to 2-1/4") 0 to 68 mm (0 to 2-11/16") Cutting depth at 45° Max. 38 mm (1-1/2") Max.

  • Page 6: Comparisons With Similarproducts

    COMPARISONS WITH SIMILAR PRODUCTS 1. Comparison of Specifications (1) 165mm (6") dia. saw blade (Superior specifications: Maker HITACHI Model C 6SS C 6MFA C 6SF C 6MF Saw blade diameter 165 (6-1/2") 165 (6-1/2") 57 (2-1/4") 56 (2-7/32") Max.cutting depth 38 (1-1/2")
  • Page 7 (2) 190mm (7-1/2") dia. saw blade (Superior specifications: Maker HITACHI Model C 7SS C 7MFA C 7SF C 7MF Saw blade diameter 190 (7-1/2") 185 (7-1/4") 68 (2-11/16") 66 (2-19/32") Max.cutting depth 46 (1-13/16") 44 (1-3/4") Power input 1,050 1,010...

  • Page 8: Precautions On Sales Promotion

    1. Safety Instructions In the interest of promoting the safest and most efficient use of the C 6SS and C 7SS Circular Saws by all of our customers, it is very important when concluding a sale that the salesperson carefully ensure that the buyer seriously recognizes the importance of the Instruction Manual, and fully understands the precautions listed on the Warning Labels, Warning Signs and Caution Labels attached to each tool.

  • Page 9: Repair Guide

    REPAIR GUIDE Before disassembly, be sure to remove the saw blade to prevent damage to the cutting edge or personal injury due to the saw blade. 1. Precautions on Disassembly and Reassembly The disassembly and reassembly procedures are described below, as well as certain precautions. The numbers in the descriptions below correspond to item numbers in the Parts List for all the models.
  • Page 10 5. Removal of the Armature (a) Remove the Lock Lever [43] and tap the end surface of the Housing Ass'y [30] with a wooden hammer. The Armature [23] and the Fan Guide [22] can then be removed. (b) Remove the Fan Guide [22], Thrust Washer [19] and Bearing Lock [18]. (c) Use a bearing puller to remove the Ball Bearing 6000VVCMPS2L [44] and Ball Bearing 608VVC2PS2L [20], and then remove Washer (A) [21].
  • Page 11 7. Removal of the Base (a) Align the bevel plate hole of Base [68] with the Gear Cover Ass’y [26] and then press-fit Roll Pin D6 x 50 [58]. (b) Loosen the Seal Lock Screw (W/Sp. Washers) M6 x 14 [62], and then remove Lever (A) [63], the Lock Nut [65], Washer (C) [67] and Bolt (Square) M6 x 20 [28].
  • Page 12 Reassembly Perform reassembly by reversing the order of the disassembly procedure. However, special attention should be given to the following items. 1. Reassembly of the Bearing Lock and Thrust Washer Before installing the Armature [23], be sure to install the Bearing Lock [18] and Thrust Washer [19] in the bearing chamber of the Housing Ass'y [30] in this order.
  • Page 13 4. Reassembly of the Stator Ass’y As shown in Fig. 7 below, insert a guide bar [J-132 stator press pins (special repair tool, Code No. 970911) are recommended] into the Stator Ass'y [38] and Housing Ass'y [30] to accurately align the screw hole on the Stator Ass'y [38] with the corresponding hole on the Housing Ass'y [30].

  • Page 14: Wiring Procedure

    6. Wiring procedure Wiring should be done by referring to Figs. 9 and 10 below. During installation, be careful not to pinch the. lead wires between the housing and handle cover. (Left: with condenser Right: None) Fig. 9 Blue (Lead wire to Brown or Black switch) (Lead wire from...

  • Page 15: Insulation Tests

    The allowable deflection level of the saw blade shall be as follows: Models Measuring points Allowable level C 6SS, C 7SS 0.3 mm max. Cleaning the case When the unit becomes soiled, use a clean, soft rag moistened with soapy water to clean it. Never use chloric solvents, gasoline or thinner (which tend to damage plastic material) for cleaning.

  • Page 16: Standard Repair Time (Unit) Schedules

    STANDARD REPAIR TIME (UNIT) SCHEDULES Variable MODEL 60 min. Fixed Work Flow C 6SS C 7SS Switch Handle Code Cover Code Armor Housing Ass’y Stator Ass’y General Assembly Armature Protective Ball Bearing Cover (608VV) Return Spring Ball Bearing (6000VV) Spindle and...

  • Page 17: Circular Saw

    LIST NO. E519 CIRCULAR SAW 2009 6 18 Model C 6SS (E1) Rev.1 C6SS 33.3% TU01694...
  • Page 18 PARTS C 6SS ITEM CODE NO. DESCRIPTION REMARKS USED 963-803 METAL 322-088 SPINDLE AND GEAR SET 331-705 SPINDLE AND GEAR SET FOR CHI, PAN, MEX 308-361 BEARING HOLDER 305-568 SEAL LOCK FLAT HD. SCREW M5 X 12 331-266 PROTECTIVE COVER...
  • Page 19 PARTS C 6SS ITEM CODE NO. DESCRIPTION REMARKS USED 999-043 CARBON BRUSH (1 PAIR) 935-829 BRUSH CAP 959-140 CONNECTOR 50091 (10 PCS.) FOR VEN, THA, INA, IND, PAN, SIN, KUW, MEX, CHI 953-327 CORD ARMOR D8.8 331-707 FASTON 340-614C STATOR ASS'Y 110V INCLUD.

  • Page 20: Standard Accessories

    STANDARD ACCESSORIES C 6SS ITEM CODE NO. DESCRIPTION REMARKS USED 944-459 HEX. BAR WRENCH 5MM 302-756 GUIDE OPTIONAL ACCESSORIES ITEM CODE NO. DESCRIPTION REMARKS USED 302-981 DUST COLLECTOR SET (D) 322-099 WASHER (A) - 4 - Printed in Japan 06 - 09...
  • Page 21 LIST NO. E520 CIRCULAR SAW 2009 6 18 Model C 7SS (E1) Rev.1 C7SS TU01695 33.3%...
  • Page 22 330-973 SIDE HANDLE EXCEPT FOR VEN, TPE, THA, INA, SIN, HKG, KUW, IND 331-272 GEAR COVER ASS'Y INCLUD. 45-47 HITACHI LABEL 942-808 BOLT (SQUARE) M6 X 20 938-477 HEX. SOCKET SET SCREW M5 X 8 331-260 HOUSING ASS'Y INCLUD. 29, 32 500-409Z CORD (CORD ARMOR D8.8)
  • Page 23 C 7SS ITEM DESCRIPTION REMARKS CODE NO. USED 500-468Z CORD (CORD ARMOR D8.8) FOR THA, CHN 500-231Z CORD (CORD ARMOR D8.8) FOR SIN 500-240Z CORD (CORD ARMRO D8.8) FOR MEX, PAN (120V) 323-974 CORD (CORD ARMOR D10.1) FOR TPE 957-051 BRUSH HOLDER 999-043 CARBON BRUSH (1 PAIR)
  • Page 24 C 7SS ITEM CODE NO. DESCRIPTION REMARKS USED 949-566 LOCK NUT M5 (10 PCS.) 328-048 LOCK NUT 331-708 PLATE 329-933 WASHER (C) 331-270 BASE INCLUD. 54-57, 61 331-271 BASE INCLUD. 54-57 FOR VEN, TPE, PAN, CHI, THA, INA, SIN, HKG, KUW, MEX, IND STANDARD ACCESSORIES ITEM DESCRIPTION...

Table of Contents