Table of Contents
Advertisement
OPERATING INSTRUCTIONS (continued)
FUNCTION MENU
MENU
Picture
Audio
Timer
Function
Setup
Language
Select
OK Set
Selected characters
Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Panel Life
Luminance Manager
Slide Interval
Reset
(off the function)
Mode Display
ID Number
Inverse
Standby White
Gamma
Function
Screen Saver
Screen Wipe
Black Side Panel
Video Power Save
Freeze Mode
Default Zoom
Panel Life
Luminance Manager
Slide Interval
Reset
Select
Off
5Min.
10Min.
60Min.
40Min.
20Min.
On
60Min.
Off
On
Off
On
Split
Strobe
Panoramic
4:3
Normal
Extend 1
Extend 2
Off
On
5sec.
10sec.
30sec.
(waiting to reset)
Off
On
1
2
3
4
7
6
5
On
60Min.
Off
15Min.
30Min.
120Min.
60Min.
2.2
2.8
Off
On 60Min.
Off
Off
Split
Panoramic
Nomal
Off
5
Reset
Set
Return
This moves the picture around the screen in small amounts, at set
intervals, to reduce the panel image retention. This is where station-
ary objects, such as screen logos, leave a slight image visible after
they should have disappeared.
The partial function might not be available in the AV monitor.
This is used to reduce the panel image retention that can occur with
stationary pictures by the white field signal. Select On (continuous
operation) or 60 Min. (time limit operation) and press the OK button.
Press the MENU or RETURN button on the remote control to return to
normal viewing.
The partial function might not be available in the AV monitor.
This turns the gray sidebars to the black sidebars when watching
normal mode screen size area. It is always set to Off when the monitor
powered On. It is recommended to set to Off to reduce the panel
image retention. This is not available for the photo input function.
The partial function might not be available in the AV monitor.
This is used to reduce power consumption for video input when there
is no video signal. Setting it On will leads the monitor to the standby
mode when the AV input with no signal is selected.
The partial function might not be available in the AV monitor.
This selects the display condition of the FREEZE mode between Split
(2 pictures) and Strobe (12 pictures). This is grayed out and not
available in the AV monitor.
The partial function might not be available in the AV monitor.
This selects the screen display size of TV input that appears first
when the main power turned on. This is grayed out and not available
in the AV monitor.
The partial function might not be available in the AV monitor.
This function is to suppress the contrast of the screen regardless of the
Contrast setting in the Picture Menu. By this control, power consumption
can be reduced or degradation of a panel can be mitigated. The order
of power consumption is Extend 2 < Extend 1 < Normal.
If the Contrast setting is changed when this item is set to Extend 1 or
2, it will be changed to Normal automatically.
The partial function might not be available in the AV monitor.
This is used to reduce the panel image retention which is caused by
especially displaying TV station logo.
Brightness of 4 corners of the panel get lower than the center.
The partial function might not be available in the AV monitor.
This is used to display images at set intervals during slide show.
(37/42 only)
* This is not available for Europe model.
The original factory settings for the items of this Menu page can be
restored by pressing the OK button.
This can display the Input Signal Screen Display every time the input
mode and signal mode are changed.
Set to OFF if the Input Signal Screen Display is not needed when
switching signals.
Assigns ID nos. to the monitors so that they can be controlled
individually (up to 7 monitors can be controlled).
This function can change each level if RGB signal invert to reduce
the panel image retention. When this function is required to use,
select On (continuous operation) or 60Min. (time limit operation) and
press OK button. And press the Menu or return button to exit.
This function is also provided against the image retention. If time is
set for this item, the screen changes into the white pattern when the
monitor enters power save mode, and it will continue for the period of
setting time.
Normally set to 2.2.
AV monitor only
Function
Mode Display
Off
ID Number
1
Inverse
On 60Min.
Standby White
Off
Gamma
2.2
Reset
Reset
Select
Set
Return
Setup hint
39
Hide quick links:
Advertisement
Table of Contents
