Hunter 99120 Getting Started

Hunter 99120 Getting Started

Universal wall mount control

Advertisement

Getting Started
OFF
Remove the canopy. If uncertain how
Before installing the Universal
to remove it, reference the fan's owner's
Remote Control Receiver,
manual. With wiring exposed, it may be
use the pull chains to set the
helpful to note existing wire connections
fan speed to HIGH and the
or take a digital photo for reference.
light to ON. Be sure power is
Remove the wire connectors that connect
OFF before proceeding with
the wires from the outlet box to the fan,
installation.
leaving the grounding wires connected.

Wiring the Receiver

CONNECT WIRES FROM
RECEIVER TO FAN - Using
the orange wire connectors,
connect the blue wire from
the receiver to the blue wire
(or possibly black with white
stripe wire) from the fan.
Connect the yellow wire from
the receiver to the black wire
from the fan.
If you are uncertain about
wire colors or connections,
please contact a qualified
electrician.
Universal Wall
Mount Control
Model #99120
Receiver
Canopy
Choose the hanging system that most closely resembles the one used by your fan and install the receiver as shown and wire as directed.
Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8" remaining. Re-strip the fan lead wires 1/2" . Place remaining excess wire into
the ceiling electrical box. The bracket and fan must remain properly grounded.
You may have installation issues if the fan is installed on an angled ceiling. For assistance, call 1-888-830-1326.

Wiring the Wall Control

CONNECT WIRES FROM
RECEIVER AND FAN TO
WIRES FROM OUTLET
BOX - Using the orange wire
connectors, connect the
black wire (ungrounded)
from the ceiling to the black
wire from the receiver.
Connect the white wire
(grounded) from the ceiling
to both the white wire from
the receiver and the white
wire from the fan.
After removing the switch plate
AFTER ALL WIRES ARE
cover, remove all wiring from
CONNECTED and secured
with wire connectors,
re-install the canopy.
M0061-01 • 01/16/14 • © Hunter Fan Company
Receiver
OR
OR
Canopy
Using orange wire connectors,
connect the two black wires
the switch.
(ungrounded) from the outlet
box. Also connect the two green
or bare wires (grounding) from
the outlet box with the grounding
wire from the wall control.
To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off
the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers
in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
www.HunterFan.com
If you are installing multiple remote-controlled fans
on the same circuit breaker,
you may need to perform a few extra steps to prevent interference
or faulty operation of your remote controls.
Go to www.HunterFan.com/FAQs and click "How do I properly
install multiple remote-controlled fans?" for more information.
For low pro le fans, the receiver should
be secured to the ceiling bracket with a
cable tie.
Ceiling
Cable Tie
Plate
OR
Receiver
Receiver
Canopy
Insert the wall control into
Install the cover plate using a
the outlet box and secure the
Phillips Head screwdriver to
two screws using a Phillips
secure the two cover plate screws.
head screwdriver.
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
1.888.830.1326
Ceiling
Bracket
Fan Body

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 99120 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hunter 99120

  • Page 1 If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel. M0061-01 • 01/16/14 • © Hunter Fan Company...
  • Page 2: Maintenance

    • Make sure the power is on at the This product conforms to UL Standard 507. The Hunter Fan Company makes the following limited warranty to the original purchaser light when you turn the lights circuit breaker and the wall switch.

Table of Contents