Advertisement
Quick Links
XS35V3L Series Quick Guide【English】
__p
Front Panel
F3
F1. Power Button
F4
F2. Power Status LED
F3. HDD Status LED
F4. SD Card Reader
F5. ODD/ Second HDD (Optional)
F6. ODD Eject Button
F7. USB 2.0 Port
F7
F8. Vertical Stand
F8
Connecting the System
4
3
2
1
5
1
Connecting Monitor or LCD TVs
Digital and analog connections are available so the device can be
connected to computer monitors, flat-panel displays, plasma or LCD TVs.
Analog: Connect this to your computer monitor or LCD TVs.
D-Sub Cable
D-Sub Port
Display with D-Sub input
Digital:
Connect this to your HDMI-enabled computer monitor,
plasma or LCD TV.
HDMI Cable
Display with HDMI input
HDMI Port
Connecting HDTV or external amplifier with HDMI output
Supports HDMI 1.3 standard with the ability to transmit audio and
video signal over the HDMI cable.
HDMI Cable
HDTV HDMI Connector
OR
HDMI Port
Amplifier HDMI Connector
Back Panel
F1
F2
B1
B1. Microphone Jack
B2
B2. Headphone/Line-out Jack
B3
B3. LAN Port
F5
B4. Kensington Lock
B5. HDMI Port (XS35V3L only)
B6. USB 2.0 Ports
F6
B7. D-Sub (VGA) Port (XS35V3L only)
B9
B8. Power Jack (DC-in)
B10
B9. D-Sub (VGA) Port (XS35GS V3L only)
B10. HDMI Port (XS35GS V3L only)
2
Connecting Keyboard/Mouse or USB Devices
USB Ports
3
Connecting LAN
Wall
RJ45 Cable
LAN Port
DSL/Cable Modem
4
Connecting Speakers and Microphonea
Microphone,
Headphone/Line-out Jack
5
Connecting Power
3
Power Jack (DC-in)
2
6
Powering on the system
A. Begin Installation
For safety reasons, please ensure that the power cord is disconnected
before opening the case.
1. Unscrew one screw of the chassis cover.
2. Slide the cover backwards and upwards.
B4
2
B5
3
B6
Screw
1
B7
B. Memory Module Installation
B8
If you install only one memory module in your system, install it in the
slot labeled "DIMM2".
1. Locate the SODIMM slot on the mainboard.
2. Align the notch of the memory module with the one of the memory
slot.
SODIMM slot
USB Keyboard/Mouse
3. Gently insert the module into the slot in a 45-degree angle.
USB Devices
4. Carefully push down the memory module until it snaps into the
locking mechanism.
Internet
2
45-degree
angle
2
1
3
Latch
Microphone/Headphone
Speakers
5. Repeat the above steps to install additional memory modules,
if required.
C. HDD Installation
1. Mount HDD into the bracket with four screws.
1
2. As shown, install the HDD & bracket in the chassis and push it
towards the direction as indicated by the red arrow to connect
the HDD connector.
L
The product's colour and specification will depend on the actual shipping product.
3. Tighten the HDD & bracket with three screws.
D. ODD or Second HDD Installation
1. Turn your XPC upside down and remove another cover.
2. As shown, install the ODD/HDD Adapter Card with two screws and
connect the cable to CN2/CN1.
For the ODD: install the ODD Adapter Card
CN2
For a second HDD: install the HDD Adapter Card
If you are installing a second HDD, tighten the two nuts first just
as shown.
1
two nuts
2
CN1
1
3. Mount ODD/HDD into the bracket with screws.
For the ODD
DIMM2
Screw
DIMM1
Bracket
For a second HDD
Latch
HDD
Screw
4. As shown, install the ODD/HDD & bracket in the chassis and push
it towards the direction as indicated by the red arrow to connect the
ODD/HDD connector.
For the ODD
ODD Connector
For a second HDD
HDD Connector
HDD Connector
5. Turn your XPC upside down and tighten the ODD/HDD & bracket
with one screw.
Screw
E. Complete
1. Replace the cover and refasten one screw.
2. Tear off the double sided protective membrane.
1
2
Protective Membrane
Screw
Using the Vertical Stand
Install vertical stand and check that it is properly aligned, then
tighten securely with one screw.
ODD
Screw
Bracket
Vertical Stand
Safety Information
Read the following precautions before setting up a XPC.
CAUTION
Incorrectly replacing the battery may damage this co-mputer.
Replace only with the same or equivalent type recommended
by the manufacturer. Disposal of used batteries according to
the manufacturer's instructions.
Laser compliance statement
The optical disc drive in this PC is a laser product.
The drive's classification label is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION: INVISIBLE LASER RADIATION WHEN
OPEN.AVOID EXPOSURE TO BEAM.
53R-XS35V3-2801
Advertisement
