Advertisement
Quick Links
XS36VL Series Quick Guide【English】
__p
Front Panel
F3
F1. Power Button
F2. Power Status LED
F4
F3. HDD Status LED
F4. Serial Ports (COM1,COM2)
F5. SD Card Reader
F6. USB 2.0 Port
F7. Vertical Stand
F4
F6
Connecting the System
4
3
2
1
5
1
Connecting Monitor or LCD TVs
Digital and analog connections are available so the device can be
connected to computer monitors, flat-panel displays, plasma or LCD TVs.
Analog: Connect this to your computer monitor or LCD TVs.
D-Sub Cable
Display with D-Sub input
DVI Cable
Display with DVI-D input
D-Sub or DVI-D Port
Digital:
Connect this to your HDMI-enabled computer monitor,
plasma or LCD TV.
HDMI Cable
Display with HDMI input
HDMI Port
Connecting HDTV or external amplifier with HDMI output
Supports HDMI 1.3 standard with the ability to transmit audio and
video signal over the HDMI cable.
HDMI Cable
HDTV HDMI Connector
OR
HDMI Port
Amplifier HDMI Connector
Back Panel
F1
F2
B1
B1. Microphone Jack
B2
B2. Headphone/Line-out Jack
B3
B3. LAN Port
B4. Kensington Lock
B5. HDMI Port
F5
B6. USB 2.0 Ports
B7. D-Sub (VGA) Port
B8. DVI-D Port
B8
B9. Power Jack (DC-in)
F7
2
Connecting Keyboard/Mouse or USB Devices
USB Keyboard/Mouse
USB Ports
3
Connecting LAN
Wall
RJ45 Cable
LAN Port
DSL/Cable Modem
4
Connecting Speakers and Microphonea
Microphone,
Headphone/Line-out Jack
5
Connecting Power
1
Power Jack (DC-in)
6
Powering on the system
A. Begin Installation
For safety reasons, please ensure that the power cord is disconnected before
opening the case.
1. Unscrew one screw of the chassis cover.
B4
2. Slide the cover backwards and upwards.
B5
B6
B7
B. Memory Module Installation
B9
If you install only one memory module in your system, install it in the slot
labeled "DIMM2".
1. Locate the SODIMM slot on the mainboard.
2. Align the notch of the memory module with
the one of the memory slot.
3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking mechanism.
USB Devices
Internet
Microphone/Headphone
Speakers
5. Repeat the above steps to install additional memory modules, if required.
C. HDD Installation
1. Mount HDD into the bracket with four screws.
2
3
2. As shown, install the HDD & bracket in the chassis and push it towards the direction as
indicated by the red arrow to connect the HDD connector.
The product's colour and specification will depend on the actual shipping product.
L
3. Tighten the HDD & bracket with three screws.
2
Screw
D. Complete
1
1. Replace the cover and refasten one screw.
2. Tear off the double sided protective membrane.
SODIMM slot
Using the Vertical Stand
DIMM2
Install vertical stand and check that it is properly aligned, then tighten securely with one
screw.
DIMM1
1
2
45-degree
angle
3
Latch
Latch
Safety Information
Read the following precautions before setting up a XPC.
CAUTION
Incorrectly replacing the battery may damage this co-mputer.Replace only with the
same or equivalent type recommended by the manufacturer. Disposal of used batteries
according to the manufacturer's instructions.
HDD Connector
Laser compliance statement
The optical disc drive in this PC is a laser product.
The drive's classification label is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN.AVOID EXPOSURE TO BEAM.
1
2
Screw
Screw
Vertical Stand
53R-XS36V3-2401
Advertisement
