Controls And Features - JVC TM-H1950CG Instructions Manual

CONTROLS AND FEATURES

FRONT VIEW
<Front Panel>
1
CHROMA CONTRAST VOLUME/SELECT MENU UNDER COLOR BLUE POWER
SCAN OFF CHECK ASPECT A B C SLOT D
PHASE BRIGHT INPUT SELECT
TM-H1950CG
(Front view of TM-H1950CG shown)
1
Tally lamp
Lights when the tally control signal is ON. The tally control
signal is input through the REMOTE (external control)
remote terminal. For details, refer to Page 18.
Chroma/Phase button
2
[ CHROMA/
Press this button to activate the picture color density
adjustment mode or picture hue adjustment mode. Each
time you press the button, the adjustment item changes.
Picture color density
Adjust the value with the VOLUME/SELECT buttons
Also used as a control button in the menu function mode.
Contrast/Brightness button
3
[CONTRAST
Press this button to activate the picture contrast adjustment
mode or picture brightness adjustment mode. Each time
you press the button, the adjustment item changes.
Picture contrast
Adjust the value with the VOLUME/SELECT buttons
Also used as a control button in the menu function mode.
Volume/Select buttons
4
[VOLUME/SELECT –
Adjusts the speaker volume. Also used as a control
button in the menu function mode.
Menu button [MENU]
5
Displays and disappears the <MENU> screen.
Pressing the CHROMA/PHASE button
button depressed will display the <SET-UP MENU>
screen.
Under Scan button [UNDER SCAN]
6
Reduces the screen size to display the entire image.
Press the button again to cancel Under Scan.
When selected, the Under Scan button lights.
Color Off button [COLOR OFF]
7
Cuts color signals to display a black and white image.
Press the button again to restore the original color.
When selected, the COLOR OFF button lights.
Note:
● This function is invalid with RGB input.
4
CHROMA CONTRAST VOLUME/SELECT
15
PHASE BRIGHT
2 3
PHASE]
f Picture hue
/ BRIGHT ]
f Picture brightness
+]
2
with the Menu
UNDER COLOR BLUE
MENU
SCAN OFF CHECK
4 5 6
7 8
8
Blue Check button [BLUE CHECK]
Cuts red and green signal components. Only blue signal
components are shown. Press the button again to
restore the normal image.
When selected, this button lights.
Aspect button [ASPECT]
9
Press this button to change the aspect ratio from 4:3 to
16:9.
10
Input A (VIDEO) button [INPUT SELECT A]
Selects the video and audio signals input to the VIDEO A
*
4 and AUDIO A
.
button lights when selected.
11 Input B (VIDEO Y/C) button [INPUT SELECT B]
Selects the video and audio signals input to the VIDEO B
(
or VIDEO B (Y/C)
the rear panel. The button lights when selected.
Note:
● The VIDEO B terminals include a video terminal (BNC
connector) and a Y/C terminal (mini-DIN 4-pin connector).
4
.
The Y/C (S-video) terminal has priority.
Input C/D (Slot) buttons [INPUT SELECT C/D
12
(SLOT)]
Selects the signals to be input via the input cards installed
in the rear panel card slots.
C, D: Selects the image from the input card in the slot.
For details on input connectors and using the INPUT
SELECT button, refer to page 7.
Power indicator
13
Unlit : The main power is OFF.
Orange : The main power is ON, but the monitor's power
is OFF (in the stand-by mode).
Green : The main power is ON, and the monitor's power
is ON (in the normal operation mode).
Power switch [POWER ]
14
Press the power switch to turn the monitor's power ON or
OFF when the main power is ON.
Note:
● When RUSH DELAY is set to SLOW, it takes about
three seconds before power is actually supplied after
the power switch is pressed.
Speaker
15
A built-in speaker is located inside the right side panel
when the monitor is viewed from the front.
ASPECT A B C SLOT D
INPUT SELECT
9 10 11 12
q
terminals on the rear panel. The
) w
and AUDIO B terminals on
POWER
13 14