JVC TM-H1950CG Instructions Manual page 15

HOW TO USE THE MENU
FUNCTIONS
Set-up menu items
PICTURE SUB ADJ.
CONTRAST
BRIGHT
CHROMA
PHASE
H. POSITION
V. POSITION
WHITE BALANCE
DRIVE R. DRIVE
B. DRIVE
CUT OFF R. CUT OFF
G. CUT OFF
B. CUT OFF
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE
*1 May not be shown depending on the type of signals input.
*2 Refer to HOW TO USE EXTERNAL CONTROL on page 18 for more details.
4. To set the other set-up menu items, repeat the
procedures 2 and 3.
5. Press the MENU button to quit.
MENU
Note:
Setting Description
MAKE Make contact system: Controls the function using the control
terminal's short-circuit and open (short-circuits or opens 15th
terminal (GND)).
TRG. Trigger system: Controls the function by short-circuiting (short-
circuits or opens 15th terminal (GND)) with pulse (about 1 sec.)
A-D Switches the input by short-circuiting a specified signal line in
INPUT A, B, C, or D.
A/B Switches between INPUT A and INPUT B with D-sub pin 2.
14
(cont'd)
Purpose
Image sub adjustment
Adjusts contrast.
Adjusts brightness.
Adjusts color density.
Adjusts hue.
Adjusts the horizontal position of the
screen (+: Horizontal position shifts
to the right/-: Horizontal position shifts to
the left)
Adjusts the vertical position of the screen
(+: Vertical position moves up/-: Vertical
position moves down)
Adjusts the white balance.
Adjusts red level.
Adjusts blue level.
Adjusts red cut off.
Adjusts green cut off.
Adjusts blue cut off.
Sets the operation buttons on the front
panel to control lock mode.
Sets the status display of the color system.
Sets the external control function method.
Sets external control of input selection.
(Shown only when REMOTE SYSTEM is
set to MAKE.)
Front panel Function
button displayed
MENU EXIT
Selects CONTRAST/BRIGHT/CHROMA/PHASE. The
selected setting screen is shown. Select the function display for
adjustment.
– 10 – 9 – 01
• •
– 10 – 9 – 01
• •
– 10 – 9 – 01
*1 • •
– 10 – 9 – 01
*1 • •
– 5 • • • – 01
– 5 – 01
• • •
Selects the drive (DRV) or cut off (CUTO) adjustment. The selected
setting screen is shown. Select the function display for adjustment.
– 20 –1 9
• •
– 20 – 1 9
• •
– 20 – 1 9
• •
– 20 –1 9
• •
– 20 – 1 9
• •
O FF ON
O FF ON
M AKE T RG.
A–D A/B
Contents
Quit (or Release) the <MENU>
screen
Settings
+ 01 + 09 + 10
00 • •
+ 01 + 09 + 10
00 • •
+ 01 + 09 + 10
00 • •
+ 01 + 09 + 10
00
• •
+ 1 + 5
00 • • •
+ 1 + 5
00 • • •
+ 01 + 19 + 20
– 01
00 • •
– 01 + 01 + 19 + 20
00 • •
+ 01 + 19 + 20
– 01 00
• •
+ 01 + 19 + 20
– 01 00
• •
+ 01 + 19 + 20
– 01
00 • •
Notes:
● When the CONTROL LOCK function is
set to ON, pressing operation buttons
on the front panel will display the
message "CONTROL LOCK ON!" on
the screen for about 3 seconds.
● The CONTROL LOCK function is
maintained even when the power is
turned off.
● To turn off the CONTROL LOCK
function, while holding the MENU button
press the CHROMA/PHASE button.
Then set the CONTROL LOCK function
to OFF.
● Even when the CONTROL LOCK
function is set to ON, the following
operations are available:
– Power Switch operation
– Volume control with the VOLUME/
SELECT buttons
– Display or disappear of the <SET-UP
MENU> screen.
● The STATUS DISPLAY function can be
set to display (ON) or not display (OFF)
the present color system when the
power is turned on or the input signal is
changed. Refer to page 9 for more
information.
● When REMOTE SYSTEM is set to
MAKE and any one of the INPUT A to D
buttons, the UNDER SCAN button,
COLOR OFF button or the ASPECT
button is pressed, "REMOTE ON!"
appears on screen for about 3 seconds.
(Not shown with CONTROL LOCK set
to ON.)
● When REMOTE SYSTEM is set to
TRG, the front panel controls can be
operated.
● INPUT REMOTE and REMOTE
SYSTEM are enabled when REMOTE
ENABLE is set to ON.
*2
*2