Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Advertisement
Table of Contents
Related Manuals for Henny Penny COLD TOPS CMC/CMR-103
Summary of Contents for Henny Penny COLD TOPS CMC/CMR-103
- Page 1 Henny Penny Cold Tops Model CMC/CMR-103 Model CMC/CMR-104 Model CMC/CMR-105 Model CMC/CMR-106 Model CMC/CMR-107 OPERATOR’S MANUAL...
- Page 2 0 TO 3 YEARS: During this time, any frypot that fails due to manufacturing or workmanship is- sues will be replaced at no charge for parts, labor, or freight. Henny Penny will either install a new frypot at no cost or provide a new or reconditioned replacement fryer at no cost.
-
Page 3: Table Of Contents
Section Section 1. INTRODUCTION ... 1-1 1-1. Henny Penny Cold Tops ... 1-1 1-2. Features ... 1-1 1-3. Proper Care ... 1-1 1-4. Assistance ... 1-1 1-5. Safety ... 1-2 Section 2. INSTALLATION... 2-1 2-1. Introduction ... 2-1 2-2. Unpacking ... 2-1 2-3. -
Page 4: Section 1. Introduction
• Front glass lifts for easy cleaning As in any unit of food service equipment, the Henny Penny cold top does require care and maintenance. Requirements for the mainte nance and cleaning are contained in this manual and must become a regular part of the operation of the unit at all times. -
Page 5: Safety
1-5. SAFETY Model CMC/CMR-103,104,105,106,107 The Henny Penny cold tops have many safety features incorporated. However, the only way to ensure a safe operation is to fully understand the proper installation, operation, and maintenance procedures. The instructions in this manual have been prepared to aid you in learning the proper procedures. -
Page 6: Section 2. Installation
2-1. INTRODUCTION 2-2. UNPACKING SECTION 2. INSTALLATION This section provides the installation for Henny Penny cold tops. Installation of this unit should be performed only by a qualified service technician. Do not puncture the unit with any objects such as drills or screws, or component damage or electrical shock could result. -
Page 7: Electrical
2-2. UNPACKING (Continued) 2-3. ELECTRICAL Model CMC/CMR-103,104,105,106,107 Take care when moving the fryer to prevent personal injury or damage to the refrigeration system. CMC-107s weigh over 700 lbs. (318 kg). Peel off any protective covering from exterior of the cabinet. Install the grids into unit. -
Page 8: Location
2-4. LOCATION 2-5. REFRIGERANT INFORMATION UL Specs CE Specs 2-6. DRAIN CONNECTION Place the cold tops in an area where product can be loaded and unloaded without interruption. For proper operation, level the unit by adjusting the bolts under the base, and leave 3 feet (91.44 cm) clearance behind the unit for ventilation and service. -
Page 9: Compressor Size And Load
2-7. COMPRESSOR SIZE AND LOAD 2-8. FOOT PRINT DRAWING DRAIN& REFRIGERATION CONNECTIONS Model CMC/CMR-103,104,105,106,107 Model CMC Motor HP CMR Motor HP CMC/ BTU Load R-22 2860 2860 2830 2830 3840 BTU load sized at evaporator temperature + 20 F or -6 C. CMR MODELS R-134a R-22 R-134a... -
Page 10: Cut Out Dimensions For Dry Base Or Table Installation
2-9. CUT OUT DIMENSIONS FOR DRY BASE OR TABLE INSTALLATION Model CMC/CMR-103,104,105,106,107... -
Page 11: Flourescent Lighting And Bulb Replacement
2-10. FLOURESCENT LIGHTING AND BULB REPLACEMENT Model CMC/CMR-103,104,105,106,107 Model of Lights CMR/CMC-103 CMR/CMC-104 CMR/CMC-105 CMR/CMC-106 CMR/CMC-107 UL Units 1. Pull the bulb out of the sockets. 2. Remove the bulb guard caps. 3. Install new fluorescent bulb in reverse order. CE Units 1. - Page 12 2-11. COLD TOP ON A COLD BASE INSTALLATION INSTRUCTIONS Figure 2-1 Figure 2-2 Figure 2-3 Model CMC/CMR-103,104,105,106,107 1. Remove bolts securing the Cold Top to the skid, and save bolts for later use. 2. Carefully set Cold Top on top of the Cold Base. Take care when moving the fryer to prevent personal injury or damage to the refrigeration system.
-
Page 13: Section 3. Operation
3-1. INTRODUCTION 3-2. OPERATING CONTROLS Fig. Item Description Power Switch Digital Display SECTION 3. OPERATION This section provides explanations of all controls, along with operating procedures and daily maintenance. Read the Introduction, Installation and Opeation Sections before operating the unit. Wait at least 4 hours before plugging the unit into an electrical supply. - Page 14 Model CMC/CMR-103,104,105,106,107 3-2. OPERATING CONTROLS (Continued) Figure 3-1...
-
Page 15: Basic Operation
3-3. BASIC OPERATION 3-4. CLEANING Model CMC/CMR-103,104,105,106,107 Turn power switch to ON position. Wait for temperature to reach operating temperature, 34 to 38° F (1.1 to 3.3° C). Place chilled product into case. Do not block the air return and air discharge vents with product. - Page 16 3-4. CLEANING (Continued) Model CMC/CMR-103,104,105,106,107 Every 3 Months: 1. Remove all electrical power supplied to the unit by unplugging the power cord from the wall, or by turning off the wall circuit breaker. 2. Remove all product from the unit. 3.
-
Page 17: Programming
3-5. PROGRAMMING Temperature Setpoint Other Parameters Model CMC/CMR-103,104,105,106,107 1. Press and hold for 4 seconds. The “DEF/SET” light flashes in display. 2. Press the to change the temperature setpoint, within 5 seconds. After 5 seconds, the last entered setpoint stays in memory. 3. - Page 18 3-5. PROGRAMMING Continued Model CMC/CMR-103,104,105,106,107 dS: defrost system (computation); dF=digifrost Feature; defrost start time based on total compressor running time rt=real time; defrost start frequency, based on real time dI: defrost interval; defrost frequency in hours, based on the selection of “dS” dE: defrost endurance;...
-
Page 19: Fluorescent Bulb Replacement
3-6. FLUORESCENT BULB REPLACEMENT Model CMC/CMR-103,104,105,106,107 UL Units 1. Pull the bulb out of the sockets. 2. Remove the bulb guard caps. 3. Install new fluorescent bulb in reverse order. CE Units 1. Remove the bulb cover. 2. Rotate the bulb. 3. - Page 20 Model CMC/CMR-103,104,105,106,107 DIAGRAM FOR CMC MODEL 1002...
- Page 21 Model CMC/CMR-103,104,105,106,107 DIAGRAM FOR CMR MODEL 1002...
- Page 22 Model CMC/CMR-103,104,105,106,107 230V-50Hz-1ph-CE 1002 3-10...
-
Page 23: Section 4. Parts Information
This section identifies and lists the replaceable parts of the Henny Penny Cold Top. Use only genuine Henny Penny parts in your cabinet. Using a part of lesser quality or substitute design may result in cabinet damage or personal injury. - Page 24 Item Part 56242-001 Side Glass-Flat-Clear 56242-002 Side Glass-Flat-Mirrored - LH 56242-003 Side Glass-Flat-Mirrored - RH 56050-001 Side Glass-HP Profile- Clear 56050-002 Side Glass-HP Profile-Mirrored - LH 56050-003 Side Glass-HP Profile-Mirrored - RH 56050-006 Side Glass-HP Profile-Mirrored-Antique White - LH 56050-007 Side Glass-HP Profile-Mirrored-Antique White - RH 56050-008 Side Glass-HP Profile-Mirrored-Shadow Black - LH...
- Page 25 Use the chart below to identify the correct canopy glass assembly and the correct gas shock configuration. (Gas shock configuration is from left to right, customer side.) Item Part 58607-001 HP (Curved Profile) - 2 well - Full Serve 58607-002 HP (Curved Profile) - 3 well - Full Serve 58607-003 HP (Curved Profile) - 4 well - Full Serve...
- Page 26 Item Part √ √ √ √ √ 1 56878 Gas Shock Tool 56343-001 Gas Ram - 100N 56343-002 Gas Ram - 200N 56343-003 Gas Ram - 300N 56343-004 Gas Ram - 400N 56343-005 Gas Ram - 500N Description Model CMC/CMR-103,104,105,106,107 Quantity 103 104 105 106 107 See chart on page 4-3...
- Page 27 Item Part 23967 Refrigeration unit 1/4 HP - CMC-103/104 23969 Refrigeration unit 1/3 HP - CMC-105/106 23968 Refrigeration unit 1/2 HP - CMC-107 23973 Evaporator-152-24 - CMC/CMR-103 23971 Evaporator - CMC/CMR-104 23972 Evaporator - CMC/CMR-105 23970 Evaporator - CMC/CMR-106 23996 Evaporator - CMC/CMR-107 √...