Related Manuals for Henny Penny HHC-990
Summary of Contents for Henny Penny HHC-990
- Page 1 Henny Penny Humidified Holding Cabinets Model HHC-990 Model HHC-992 Model HHC-993 Model HHC-996 Model HHC-997 Model HHC-998 OPERATOR’S MANUAL...
- Page 2 0 TO 3 YEARS: During this time, any frypot that fails due to manufacturing or workmanship is- sues will be replaced at no charge for parts, labor, or freight. Henny Penny will either install a new frypot at no cost or provide a new or reconditioned replacement fryer at no cost.
-
Page 3: Table Of Contents
Section 4. PROGRAMMING 4-1. Timer Programming ... 4-2. Clock Set ... 4-3. Special Programming ... Section 5. TROUBLESHOOTING 5-1. Troubleshooting Guide ... 5-2. Error Codes and Warnings ... GLOSSARY ... Distributors List - Domestic and International TABLE OF CONTENTS Model HHC-990 Page... -
Page 4: Section 1. Introduction
• Food probe supplied to easily display food temperature As in any unit of food service equipment, the Henny Penny humidi- fied holding cabinet does require care and maintenance. Require- ments for the maintenance and cleaning are contained in this manual and must become a regular part of the operation of the unit at all times. -
Page 5: Safety
1-5. SAFETY The Henny Penny Humidified Holding Cabinet has safety features incorporated. However, to ensure a safe operation, read and fully understand the proper installation, operation, and maintenance procedures. The instructions in this manual have been prepared to aid you in learning the proper proce- dures. -
Page 6: Section 2. Installation
Do not puncture the skin of the unit with drills or screws, or component damage or electrical shock could result. The Henny Penny humidified holding cabinet has been tested, inspected, and expertly packed to ensure arrival at its destination in the best possible condition. -
Page 7: Location
Place the humidified holding cabinet in an area that allows the doors to be opened without interference of loading and unloading product. Also, keep the unit level for proper operation. No minimum clearances are required for the rear and sides of the cabinet. Model HHC-990... -
Page 8: Electrical Connection
If the electrical supply to the unit is a cord and plug, then the electrical receptacle, for the plug, must be easily accessible.Refer to the table below for the electrical ratings for the HHC-990 series cabinets. Model... -
Page 9: Cabinet Dimensions And Weights
31-3/4” (806 mm) 27-3/4” (705 mm) 31-3/4” (806 mm) 27-3/4” (705 mm) 31-3/4” (806 mm) 27-3/4” (705 mm) 31-3/4” (806 mm) Model HHC-990 72-1/4” (1835 mm) Depth Shipping Weight 220 lbs (100 kg) 367 lbs (167 kg) 493 lbs (224 kg) -
Page 10: Probe Clip (Optional)
Remove one of the module screws and mount the probe clip with that screw. See photo at left. The food probe is accessed easier if the clip is mounted on the side of the unit that the door opens. See photo below. Mount clip here. Model HHC-990... -
Page 11: Section 3. Operation
Program Mode, shows previous settings; pressing this along with the Information Mode which has historic information on the cabinet’s performance Used to adjust the value of the currently displayed setting in the Program Mode Model HHC-990 accesses... - Page 12 “0:00”, and the control beeps; the HHC-990 and 996 have 15 timers, and the HHC-993 and 998 have 5 timers...
- Page 13 3-2. OPERATING CONTROLS (Continued) Control Decal Figure 3-1 Model HHC-990...
-
Page 14: Start-Up
(minimum 1 gallon) up to the slot on the concentration ring. See figure 3-2. Do not overfill the water pan, or water could over flow and spill onto the floor, and personal injury could result. Model HHC-990... -
Page 15: Operation With Product
“WATER LEVEL LOW”. Add more water to the water pan. Open the doors only as necessary to load and unload product. This helps to keep the interior conditions constant and saves energy. Model HHC-990 F (66 C). Use the food... -
Page 16: Cleaning Procedures
Wipe the control panel with a damp cloth. Do not splash water around controls. Reinstall racks, and leave a door partially open over night to allow interior cabinet to thoroughly dry. Model HHC-990... - Page 17 Unit is now ready for use. Monthly: Remove the 2 screws securing the vented panel on the rear of the module and remove the panel, and clean vents. Using a cloth or sponge, clean the trough once a month. Model HHC-990...
-
Page 18: Section 4. Programming
“CLOCK SET” shows in display. After 5 seconds, “ENTER CODE” shows in display. Press “CS-1, SET, HOUR”, and the time of day (with the hour flashing) shows in the display. Press the to change the hours. Model HHC-990 , and new timer... - Page 19 “CS-4, SET, DATE” shows in the display, with the date flashing. Press to change the date. Press and “CS-5, SET, YEAR” shows in the display, with the year flashing. Press to change the year. Press and hold to exit programming. Model HHC-990...
-
Page 20: Special Programming
8. Press and “SP-3, AIRTEMP SETPOINT,” and the preset cabinet temperature shows in display. 9. Press to change the air temperature setpoint, F (60 C) minimum, 210 Model HHC-990 F (99 C) maximum. - Page 21 We recommend a setpoint temperature of 425 19. Press to change the setpoint. Model HHC-990 F (60 C) maximum. F (232 F (218...
- Page 22 Special Programming Mode. For more information on the other settings of Special Programming, call your local Henny Penny distributor in your area, or call Henny Penny Corp. at 1-800-417-8405 or 1-937-456-8405. Model HHC-990...
-
Page 23: Section 5. Troubleshooting
• Door gasket torn or worn More detailed troubleshooting information is available in the Technical Manual, available at www.hennypenny.com, CAUSE or 1-800-417-8405 or 1-937-456-8405. Model HHC-990 CORRECTION • Keep doors closed except to load and serve product • Hold product only for recom- mended times •... -
Page 24: Error Codes And Warnings
• Turn switch to OFF position, then back to ON; if the display shows “E-6”, the temperature probe should be checked; once the temperature probe is repaired, or replaced, the controls should return to normal; if “E-6” persists, have the PC board replaced Model HHC-990 Panel Board Correction... - Page 25 2 complete pieces of insulation are on water heater cover under the water heater cover; if “E-18” loose, or water heater persists, have PC board replaced insulation missing or damaged Model HHC-990 Panel Board Correction...
- Page 26 “PLEASE DE-LIME WATER PAN” persists, have PC board replaced • Fill water pan, in bottom of unit, to the maximum water fill mark; this warning or empty won’t shut down the heat or humidity Model HHC-990 Panel Board Correction...
-
Page 27: Glossary
G L O S S A R Y HENNY PENNY HOLDING CABINETS a round device located inside the cabinet that measures the inside air temperature and sends that information to the control panel a metal assembly located in the water pan in the bottom of the unit that... - Page 28 NOT be used to clean a holding cabinet the area in the cabinet that holds water for creating humidity inside the cabinet Model HHC-990...