Listening Through A Home Theatre; Troubleshooting For Anynet - Samsung PDP-TELEVISION Owner's Instructions Manual

Listening through a Home theatre

You can listen to sound through a receiver (home theatre) instead of the TV's speakers.
1 Press the Anynet+ button.
2 Press the ▲ or ▼ button to select Receiver, press the ◄ or ► button to select to On. Now you can
listen to sound through the Home theatre receiver.
Press the EXIT button to exit.
➢
When the receiver (home theatre) is set to On, you can hear sound output from the TV's Optical jack.
When the TV is displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theatre
receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only
2 channel sound will be heard from the Home Theatre receiver.
➢
If your Home Theatre receiver supports audio only, it may not appear in the device list.
➢
The receiver will work when you have properly connected the Optical IN jack of the receiver to the
Optical Out jack of the TV.
➢
When using the WISELINK feature, sound may not output properly through the receiver.
➢
When listening through the receiver, there are restrictions for using the PIP and audio-related(MTS,
Preferred language) menus.

Troubleshooting for Anynet+

Symptom
Anynet+ does not work.
I want to start Anynet+.
I want to exit Anynet+.
The Connecting to Anynet+
device...message appears
on the screen.
The Anynet+ device does
not play.
The connected device is
not displayed.
The TV program cannot be
recorded.
The TV sound is not output
through the receiver.
Solution
■ Check if the device is an Anynet+ device. The Anynet+ system
supports Anynet+ devices only.
■ Connect only one receiver (home theatre).
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device's Video/Audio/HDMI cable connections.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn't work at a certain condition. (Searching channels,
operating WISELINK)
■ When connecting or removing the HDMI cable, please make sure to
search devices again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
■ Check if the Anynet+ device is properly connected to the TV and check
if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu.
■ Press the TV button on the TV remote control to switch to TV. Then
press the Anynet+ button to show the Anynet+ menu and select a
menu you want.
■ Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a
device other than Anynet+ devices.
■ Press any of CH, CH LIST, PRE-CH, and FAV.CH to change to the TV
mode. (Note that the channel button operates only when an Anynet+
device with a built-in tuner is not connected.)
■ You cannot use the remote control when you are configuring Anynet+
or switching to a view mode.
■ Use the remote control when the Anynet+ setting or switching to view
mode is complete.
■ You cannot use the play function when Plug & Play is in progress.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI cable is properly connected.
■ Check whether <Anynet+ (HDMI-CEC) Setup> is set to <On> in the
Anynet+ setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI cable only. Some
HDMI cables may not support Anynet+ functions.
■ Check whether the antenna jack on the recording device is properly
connected.
■ Connect the optical cable between TV and the receiver.
English - 68