Remote Control; Installing The Batteries For The Remote Control - Philips DVP3355V User Manual

Remote Control

Installing the Batteries for
the Remote Control
Install two AAA batteries (supplied)
matching the polarity indicated inside
the battery compartment of the Remote
Control.
1
2
Keep in mind the following when using the
Remote Control:
• Make sure that there are no obstacles
between the Remote Control and the
infrared sensor window on the Unit.
• The maximum operable infrared signal
ranges from the Remote Control are as
follows.
- Line of sight: approx. 23 feet (7m)
- Either side of center:
approx. 16 feet (5m) within 30°
- Above: approx. 16 feet (5m) within 15°
- Below: approx. 10 feet (3m) within 30°
Note(s):
• Do not mix alkaline and manganese batteries.
• Do not mix old and new batteries.
• Always remove batteries from Remote
Control if they are dead or if the Remote
Control is not to be used for an extended
period of time. This will prevent battery acid
from leaking into the battery compartment.
• If you turn off this Unit, [OPEN/CLOSE A] on
the Unit or Remote Control is not available.
Media
Button
(Alphabetical order) )
3
DVD mode
• To select chapter or title
• To select track directly.
directly.
through a disc.
• To search forward/backward
• To begin slow forward/reverse
through a disc.
playback in the pause mode.
• To repeat between your chosen • To repeat between your
point A and B. chosen point A and B.
• To select camera angles on a
disc.
• To select audio languages on a • To select "STEREO", "L-ch" or
disc. "R-ch".
• To clear the markers.
• To remove status number in
• To clear the markers.
program input.
• To clear numbers entered
• To clear numbers entered
incorrectly.
incorrectly.
• To cancel the point for A-B
• To cancel the point for A-B
repeat.
repeat.
• To call up the disc menu on a
disc.
• To display the current disc • To display the current disc
mode. mode.
• To select DVD output mode. • To select the DVD output mode.
• To activate DVD mode. • To activate DVD mode.
• To arrange the playing order or
• To set black level on/off.
play randomly.
• To move the cursor and • To move the cursor and
determine its position. determine its position.
• To open or close the disc tray. • To open or close the disc tray.
• To pause disc playback.
• To advance playback one frame • To pause disc playback.
at a time.
• To begin disc playback. • To begin disc playback.
• To skip chapters or titles. • To skip tracks.
• To play back a track or disc
• To play back a chapter or title
repeatedly.
repeatedly.
• To return to the previous • To return to the previous
operation in menu. operation in menu.
• To search track.
• To search chapter, title or time.
• To search time.
• To set or search the markers. • To set or search the markers.
• To call up the DVD setup menu. • To call up the DVD setup menu. • To call up the VCR menu.
• To turn the Unit on or to turn the • To turn the Unit on or to turn the
Unit into the standby mode. (To Unit into the standby mode. (To
completely turn off the Unit, you completely turn off the Unit, you
must unplug the AC power cord.) p g p ) must unplug the AC power cord.)
• To stop playback. • To stop playback.
• To select subtitles on a disc.
• To call up the top menu on a
disc.
• To magnify part of a picture.
(2x/4x)
– 14 – –
VCR mode
• To forward/backward a tape.
• To begin slow forward
playback in the pause mode.
• To select "HIFI" or "MONO"
mode during playback.
(Hi-Fi tapes only)
• To exit the VCR menu.
• To reset the tape counter.
• To display the current time, tape
counter and L1 or L2.
• To select input "L1" or "L2".
• To select an item on
the VCR menu.
• To advance to the
next VCR menu.
• To go back one step
during clock and
timer programming.
• To eject the cassette tape from
the cassette compartment.
• To pause tape playback or
recording.
• To advance playback one frame
at a time.
• To begin tape playback.
• To start recording or one-touch
timer recording (OTR).
• To select the repeat mode on/
off.
• To call up the index or time
search menu.
• To select the recording speed.
• To turn the Unit on or to turn the
Unit into the standby mode. (To
completely turn off the Unit, you
p g p ) must unplug the AC power cord.) p g
• To stop playback or recording.
• To adjust the tracking manually
during playback.
• To put the VCR into standby
mode for a timer recording.
• To select the VCR output mode.
• To activate VCR mode.
p )
EN