Table of Contents
Advertisement
Models:
SL-550TV-IPI-E
SL-750TV-IPI-E
SL-950TV-IPI-E
• Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppli-
er's instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08
Owner's Manual
• Leave this manual with
party responsible for use
and operation.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fi replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other fl ammable
materials.
• Keep clothing, furniture, draperies and other fl ammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.
A CO detector shall be installed in the room where the appliance
in installed.
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.
Installation and Operation
1
Advertisement
Table of Contents
Related Manuals for Heat & Glo SL-550TV-IPI-E
Summary of Contents for Heat & Glo SL-550TV-IPI-E
- Page 1 Models: SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E • Important operating a n d m a i n t e n a n c e instructions included. WARNING: If the information in these instructions is not followed exactly, a fi re or explosion may result causing property damage, personal injury, or death.
-
Page 2: Congratulations
Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. A. Congratulations Congratulations on selecting a Heat & Glo gas fi replace, an elegant and clean alternative to wood burning fi replaces. The Heat & Glo gas fi replace you have selected is designed to provide the utmost in safety, reliability, and effi... -
Page 3: Table Of Contents
Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. • CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. •... - Page 4 14 Appliance Setup A. Remove Glass Assembly ......33 B. Remove the Shipping Materials ....33 C.
-
Page 5: Limited Lifetime Warranty
B. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTY Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts. - Page 6 B. Limited Lifetime Warranty (continued) • This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, baffl...
-
Page 7: Listing And Code Approvals
Listing and Code Approvals A. Appliance Certifi cation MODELS: SL-550TV-IPI-E, SL-750TV-IPI-E, SL-950TV-IPI-E LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: B-Vent Decorative STANDARD: ANSI Z21.50-2007 • CSA 2.22-2007 This product is listed to ANSI standards for “Vented Gas Fireplaces” and “Gas Fired Appliances for Use at High Altitudes”. -
Page 8: High Altitude Installations
D. High Altitude Installations NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction. When installing above 2000 feet elevation: • In the USA: Reduce input rate 4% for each 1000 feet above 2000 feet. -
Page 9: User Guide
Operating Instructions A. Gas Fireplace Safety WARNING HOT SURFACES! Glass and other surfaces are hot during operation AND cool down. Hot glass will cause burns. • DO NOT touch glass until it is cooled • NEVER allow children to touch glass •... -
Page 10: Fan Kit (Optional)
C. Fan Kit (optional) • Refer to Figures 2.2 and 2.3 for location of control. RHEOSTAT SWITCH Figure 2.2 Fan Wiring with Rheostat VARIABLE SPEED SWITCH TEMPERATURE SENSOR SWITCH BLUE Figure 2.3 Detail of Fan Wiring with Rheostat D. Clear Space WARNING! DO NOT place combustible objects in front of the fi... -
Page 11: For Your Safety Read Before Lighting
I. Lighting Instructions (IPI) The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer. FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fi re or explosion may result causing property damage, personal injury or loss of life. -
Page 12: After Fireplace Is Lit
J. After Fireplace is Lit Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • Turn the fi replace off and allow it to completely cool. • Remove fi xed glass assembly. See Section 14.G. •... -
Page 13: Maintenance And Service
Maintenance and Service Any safety screen or guard removed for servicing must be replaced prior to operating the fi replace. When properly maintained, your fi replace will give you many years of trouble-free service. We recommend an- nual service by a qualifi ed service technician. A. -
Page 14: Maintenance Tasks-Qualifi Ed Service Technician
Venting Frequency: Seasonally By: Homeowner Tools needed: Protective gloves and safety glasses. • Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc. • Verify termination cap clearance to subsequent construc- tion (building additions, decks, fences, or sheds). See Section 6. - Page 15 (Either cobrahead or SIT) Figure 3.2 IPI Pilot Flame Patterns Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08...
-
Page 16: Installer Guide
Getting Started A. Typical Appliance System NOTICE: Illustrations and photos refl ect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual NON-COMBUSTIBLE ROOF FLASHING MAINTAINS MINIMUM CLEARANCE AROUND PIPE VENT PIPE (SECTIONS 7 and 8) CEILING FIRESTOP... -
Page 17: Design And Installation Considerations
B. Design and Installation Considerations Heat & Glo B-type vent gas appliances are designed to operate with all exhaust gases expelled to the outside of the building, and combustion air pulled from the room. Installation MUST comply with local, regional, state and national codes and regulations. -
Page 18: Negative Pressure
E. Negative Pressure WARNING! Asphyxiation Negative pressure can Risk! cause spillage of combustion fumes and soot. Fireplace needs to draft properly for safety. Draft is the pressure difference needed to vent fi replaces successfully. Considerations for successful draft include: • Preventing negative pressure •... -
Page 19: Framing And Clearances
WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access. Due to high temperatures, the appliance should be locat- ed out of traffi c and away from furniture and draperies. Model Inches SL-550TV-IPI-E Millimeters Inches SL-750TV-IPI-E Millimeters Inches... -
Page 20: Constructing The Appliance Chase
Rough Models Opening Opening (Vent Pipe) (Height) SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E * Adjust framing dimensions for interior sheathing (such as sheetrock) Figure 5.2 Clearances to Combustibles Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08 To further prevent drafts, the wall shield and ceiling fi... -
Page 21: Mantel And Wall Projections
D. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear- ances as specifi ed. Framing or fi nishing material closer than the minimums listed must be constructed entirely of noncom- bustible materials (i.e., steel studs, concrete board, etc). Combustible Mantels TOP OF HOOD OR FIREPLACE OPENING Note: All measurements are in inches. -
Page 22: Termination Locations
Termination Locations A. Vent Termination Minimum Clearances WARNING Fire Risk. Maintain vent clearance to combustibles as specifi ed. • DO NOT pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause overheating and fi re. 8 FEET LOWEST DISCHARGE... -
Page 23: Vent Information And Diagrams
Incorrect pipe may cause spill- age, condensation and overheating. These models require the following size B-vent double wall, or single wall rigid or fl ex vent pipe. Models SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E • Follow pipe manufacturer’s installation guidelines when installing the appliance. -
Page 24: Vent Clearances And Framing
Vent Clearances and Framing A. Pipe Clearances to Combustibles Vent clearances are per vent manufacturer’s specifi ca- tions. MUST be Listed B-Vent pipe. WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: •... -
Page 25: Appliance Preparation
Appliance Preparation A. Installing Outside Air Kit Damper Assem- CAUTION! Risk of Cuts/Abrasions/Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. WARNING! Risk of Fire/ Asphyxiation. DO NOT draw out- side combustion air from: •... -
Page 26: Installing Vent Pipe
Installing Vent Pipe A. Assembly of Vent Sections This B-Vent appliance requires 5-inch (SL-550/750TV-IPI- E) or 6-inch (SL-950TV-IPI-E) B-vent double-wall pipe. Follow the pipe manufacturer’s installation guidelines when installing the unit. This will ensure proper operation and prevent safety hazards. WARNING! Risk of Fire/Exhaust Fumes! Assemble pipe sections per B-vent manufacturer’s instructions. -
Page 27: Gas Information
11 11 Gas Information A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home Technologies specifi ed and approved parts. B. Gas Pressure •... -
Page 28: Electrical Information
Electrical Information A. Wiring Requirements NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1. •... - Page 29 BATTERY PACK Figure 12.1 Intellifi re Pilot Ignition (IPI) Wiring Diagram with Wall Switch or Thermostat PLUG IN Figure 12.2 Intellifi re Pilot Ignition (IPI) Wiring Diagram with Remote Receiver Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08 INTERMITTENT IGNITION MODULE 3 VAC...
-
Page 30: Junction Box Installation
E. Junction Box Installation If the box is being wired from the INSIDE of the appli- ance: • Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to dis- engage it from the outer shell (see Figure 12.4). •... -
Page 31: Finishing
Finishing A. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear- ances as specifi ed. Framing closer than the minimums list- ed must be constructed entirely of noncombustible materi- als (i.e., steel studs, concrete board, etc.) Failure to comply could cause fi... -
Page 32: Facing Material
B. Facing Material • Metal front faces may be covered with non-combustible materials only. • Facing and/or fi nishing materials must not interfere with air fl ow through louvers, operation of louvers or doors, or access for service. • Facing and/or fi nishing materials must never overhang into the glass opening. -
Page 33: Appliance Setup
Appliance Setup A. Remove Glass Assembly See Section 14.G. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity. D. -
Page 34: Lava Rock, Mineral Wool/Ember Placement
E. Lava Rock, Mineral Wool/Ember Placement Placing the Lava Rock See Section 14.F for Lava Rock placement instructions. WARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT place embers directly over burner ports. Replace ember material annually. Improperly placed embers interfere with proper burner operation. -
Page 35: Install The Log Assembly
F. Install the Log Assembly If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions. Note: Figure 1 illustrates the recommended gap between the burner and the lava rock retainer. - Page 36 Figure 6 Figure 6 Swing knot towards log #3 Swing knot towards log #3 Mate notch with grate tine Mate notch with grate tine Figure 8 Figure 8 Log #4: Locate the notch at the end of log # 4. Mate the notch with the tine as shown above.
-
Page 37: Fixed Glass Assembly
• Tighten the wing nut. NOTICE: If sooting occurs, provide more air by opening the air shutter. SHUTTER ADJUSTMENT Figure 14.4 Air Shutter Air Shutter Settings Models SL-550TV-IPI-E Fully Closed SL-750TV-IPI-E Fully Closed SL-950TV-IPI-E 3/16 in. 3/16 in. 3/16 in. -
Page 38: Troubleshooting
Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualifi ed service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualifi ed service technician. Contact your dealer to arrange a service call by a qualifi... - Page 39 Intellifi re Ignition System - (continued) Symptom A. A shorted or loose connection in fl ame 4. Pilot lights but contin- sensing rod. ues to spark, and main burner will not ignite. (If the pilot continues to spark after the B.
-
Page 40: Reference Materials
Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5. GAS LINE ACCESS 18-1/16 27-3/16 SL-550TV-E 21-1/2 32-1/16 33-9/16 34-9/16 5-1/2 3-13/16 16-5/16 8-3/8 1/2 30-3/4 15-3/8 15-13/16 5-1/16 SL-750TV-E mm 1040 917 23-9/16 39-1/16 37-9/16 38-9/16 5-1/2 3-13/16 16-5/16 8-3/8 1/2 37-3/4 18-7/8 15-13/16 6-1/16... -
Page 41: Service Parts
SL-550TV-IPI-E B. Service Parts Service Parts Diagram Beginning Manufacturing Date: June 2007 Ending Manufacturing Date:_________ Log Set Assembly Part number list on following page. Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08... -
Page 42: Service Parts List
Pilot Orifi ce NG Pilot Orifi ce LP Regulator NG Regulator LP Additional service part numbers appear on following page. Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08 SL-550TV-IPI-E COMMENTS PART NUMBER LOGS-550-E SRV2115-701 SRV2115-702... - Page 43 SL-750TV-IPI-E Service Parts Beginning Manufacturing Date: June 2007 Service Parts Diagram Ending Manufacturing Date: ________ Log Set Assembly Part number list on following page. Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08...
- Page 44 Service Parts List IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. ITEM DESCRIPTION Log Set Assembly Log 1 Log 2 Log 3...
- Page 45 SL-950TV-IPI-E Service Parts Beginning Manufacturing Date: June 2007 Service Parts Diagram Ending Manufacturing Date: ________ Log Set Assembly Part number list on following page. Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08...
- Page 46 Service Parts List IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. ITEM DESCRIPTION Log Set Assembly Log 1 Log 2 Log 3...
- Page 47 Valve NG Valve LP Flex Ball Valve Assembly Valve Bracket Heat & Glo • SL-550 / 750 / 950TV-IPI-E • 2119-900 Rev. H • 11/08 SL-550TV-IPI-E SL-750TV-IPI-E SL-950TV-IPI-E SL-550 / 750 / 950TV-IPI-E Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: ______...
-
Page 48: Contact Information
C. Contact Information Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer, ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ • Important operating a n d m a i n t e n a n c e instructions included.
Need help?
Do you have a question about the SL-550TV-IPI-E and is the answer not in the manual?
Questions and answers