Heat & Glo NorthStar-BK Owner's Manual page 2

Congratulations on selecting a Heat & Glo gas appliance - an
elegant and clean alternative to wood burning appliances.
The Heat & Glo gas appliance you have selected is designed
to provide the utmost in safety, reliability, and efficiency.
As the owner of a new appliance, you'll want to read and
carefully follow all of the instructions contained in this
Owner's Manual. Pay special attention to all Cautions and
Warnings.
LOCATION: ATTACHED TO APPLIANCE WITH BEADED CHAIN
O-T L Portland
Tested and
Oregon USA
Listed by
C US
Report #061-S-50-2
A division of Hearth & Home Technologies Inc.
TESTED TO:
20802 Kensington Boulevard, Lakeville, MN 55044
UL 127, ULC-S610-M87
LISTED FIREPLACE, SOLID FUEL TYPE, ALSO SUITABLE FOR MOBILE
HOME INSTALLATION. (UM) 84 HUD. "For Use with Solid Wood Fuel Only."
Install and use only in accordance with manufacturer's installation, venting and operating instructions.
Any area incorporating warm or cold air ducts shall be enclosed in accordance with the manufacturer's
installation instructions.
Contact Your Local Building Or Fire Officials Or Authority Having Jurisdiction About Restrictions,
Installation Inspection And Permits Required In Your Area.
WARNING - For Mobile Homes: Do not install in a sleeping room. An outside combustion air inlet
must be provided and unrestricted while unit is in use. The structural integrity of the mobile home floor,
ceiling and walls must be maintained. The fireplace needs to be properly grounded to the frame of the
mobile home.
Components required for installation: HTI SLSeries Pipe, Termination Cap, Hearth Extension and required
accessory Chimney Air Kit Part CAK4A.
Do not connect this unit to a chimney serving another appliance.
DANGER: Risk of electrical shock. Disconnect power supply before servicing.
Electrical Rating: 115 VAC <3.0 AMPS 60 Hz
Do not use grate or elevate fire. Build wood fire directly on firebrick.
Do not overfire. If heater or chimney connector glows, you are overfiring.
Do not use a fireplace insert or other products not specified for use with this product.
WARNING - THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED GAS LOG SET OR ANY LOG SET.
TO REDUCE RISK OF FIRE OR INJURY, DO NOT INSTALL AN UNVENTED GAS LOG SET OR ANY LOG SET
INTO FIREPLACE.
Must provide a source of air to prevent air starvation from combustion which could result of high levels
of carbon monoxide.
Replace glass only with 5mm ceramic available from your dealer.
Optional Fire Screen, Part SCR-433, may be used ONLY in USA
U.S. ENVIRONMENTAL PROTECTION AGENCY - Certified to comply with July 1990 particulate emission standards.
Mfg by:
Page 2
Read this manual before installing or operating this appliance.
Please retain this owner's manual for future reference.
Congratulations
SAMPLE OF SERIAL NUMBER / SAFETY LABEL
N
ORTH
E C
PA ERTIFIED
www.heatnglo.com
2008 2009 2010 Jan Feb Mar Apr May June July Aug Sept Oct. Nov. Dec.
DO NOT REMOVE THIS LABEL
Heat & Glo • NorthStar EPA Fireplace • 480-1081C
This Owner's Manual should be retained for future reference.
We suggest that you keep it with your other important
documents and product manuals.
Your new Heat & Glo gas appliance will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of fireplace products!
Model:
Serial No / Numéro De Série
S
007
TAR
F
IREPLACE
Minimum Clearances To Combustible Material
Chimney sections at any level require a 2 inches (51mm)
minimum air space clearance between the framing and
chimney section.
WITHIN ENCLOSURE AREA
Appliance to backwall
Appliance to sidewall
Duct boots to framing
Top standoffs to header
EXPOSED SURFACES
Faceplate to sidewall
Remote outlet air grills to ceiling
MANTEL
Mantel from base of fireplace
Maximum mantel depth
FLOOR PROTECTION
Combustible flooring 20 inches (508mm) in front of and 8 inches
(203mm) to either side of the fuel opening must be insulated with
non-combustible floor protection with a minimum thickness of 1
inch (25mm) and ("k" value = 0.43).
In Canada: The hearth extension must be installed according to
the installation instructions.
Made in U.S.A
Serial No.
Model Name
1" (25mm)
1" (25mm)
0" (0mm)
Test Lab
0" (0mm")
& Report No.
16" (406mm)
12" (305mm)
60" (1524mm)
12" (305mm)
Manufactured
Date
480-1100
September 1, 2008