Table of Contents
Advertisement
Quick Links
Installation
Instructions
Full Size Laundry
Center
Gas & Electric
Before
beginning
installation,
carefully
read these
instructions.
This will
simplify
the installation
and ensure
the
laundry
center
is installed
correctly
and safely.
Leave
these
instructions
near the
laundry
center
after
installation
for future
reference.
NOTE:
The electrical
service
to the laundry
center
must conform
with
local codes and ordinances
and
the
latest
edition
of the
National
Electrical
Code,
ANSI/NFPA
70, or in Canada,
CSA C22.1
Canadian
Electrical
Code
Part
1.
NOTE: The gas service to the laundry
center must conform with local codes and ordinances
and
the latest edition
of the National
Fuel Gas Code ANSI Z223.1 or in Canada, CAN/CGA
B149.12.
NOTE:
The
laundry
center
is designed
under
ANSI
Z21.5.1
or ANSI/UL
2158
- CAN/CSA
C22.2
(latest
edition)
for
HOME
USE only.
This
laundry
center
is not
recommended
for
commercial
applications
such as restaurants
or beauty
salons,
etc.
For your safety the information
in
this manual must be followed to minimize
the risk
of fire or explosion
or to prevent property damage,
personal
injury or loss of life.
ll_e aa_...,lne
or
- DO not store or
<
._q,,r
other
flammable
vapors
and
liquid
in the
vicinity
ol this
or any
other
appliance.
- WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any appliance.
• Do not touch any electrical
switch; do not use
any phone in your building.
• Clear the room, building or area of all
occupants.
• Immediately
call your gas supplier
from a
neighbor's
phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier,
call the
fire department.
Installation and service must be performed by a
qualified
installer,
service
agency or the gas
supplier.
_rinted in U.S.A.
Contents
SUBJECT
Pre-lnstallation Requirements
Electrical Requirements
Drain Requirements
Exhaust System Requirements
Gas Supply Requirements
Location
Mobile Home Installation
Rough-In Dimensions
Unpacking
Electrical Installation
Grounding Requirements
3 & 4-Wire Connections
Installation
Replacement Parts
PAGE
2
2
2
2
3
4
4
4
5
5
6
6
7
7
8
PiN134182900 (0212)
Advertisement
Table of Contents
Related Manuals for Frigidaire FLSG62MRFS4
Summary of Contents for Frigidaire FLSG62MRFS4
- Page 1 Installation Instructions Full Size Laundry Center Gas & Electric Before beginning installation, carefully read these instructions. This will simplify the installation and ensure laundry center is installed correctly and safely. Leave these instructions near the laundry center after installation for future reference.
-
Page 2: Pre-Installation Requirements
POWER SUPPLY CORD - The gas laundry center is equipped PRE-INSTALLATION REQUIREMENTS with a 120 volt 3-wire power cord. Tools and Materials Required for Installation: I. Phillips head screwdriver. 2. Channel-lock adjustable pliers. 3. Carpenter's level. NOTE: Do not under 4. -
Page 3: Exhaust System Requirements
EXHAUST SYSTEM REQUIREMENTS The maximum length of the exhaust system depends upon the type of duct used, number of elbows and type of exhaust Use only 4 inch (10.16 cm) diameter (minimum) rigid or flexible hood. metal duct and approved vent hood which has a swing-out damper(s) that opens when the dryer is in operation. -
Page 4: Gas Supply Requirements
The following illustrations show minimum clearance GAS SUPPLY REQUIREMENTS dimensions for proper operation in a recess or closet 1. Installation MUST conform with local codes, or in the installation. absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition) or in Canada, the current 0 IN. -
Page 5: Shipping Blocks
ROUGH-IN DIMENSIONS (64.13 CM) .2-1/2 (6.35 CM) 47 IN. (119,38 CM) 16-1/4 (41.27 CM) GAS SUPPLY 1-7!8 IN. (4.76 CM) 75-1/2 (191, 7 CM) (13,33 5-1/4 IN.l 41 1! 43 IN. (109.22CM) _ 4-13116 IN. WATER INLETS ,.j. (,o,.77ca, (12.22 CM) 54-5/16 IN. -
Page 6: Electrical Installation
ELECTRICAL INSTALLATION For a permanently connected laundry center: The laundry center MUST be connected to a grounded metal, ALL ELECTRIC Laundry Centers permanent wiring system; or an equipment grounding conductor MUST be run with the circuit conductors The following are specific requirements for connected to the equipment-grounding terminal or lead on proper and safe electrical installation... -
Page 7: Installation
ELECTRICAL CONNECTIONS Attach the white (neutral) wire from the power cord and the green ground wire from the appliance harness to the FOR A 3-WIRE SYSTEM silver-colored center terminal on the terminal block. ELECTRIC Laundry Center Tighten the screw securely. 1, Remove the screw securing the Gsc_w n Ground terminal... -
Page 8: Replacement Parts
10. Connect the exhaust duct to outside duct work. Use duct GAS CONNECTION (Gas laundry centers only) tape to seal all joints. a. Remove the shipping cap from gas pipe at the rear of 11. Plug the power cord into a grounded outlet. the dryer, NOTE: Check to ensure the power isoff at a circuit breaker/ NOTE: DO NOT connect the laundry center to natural gas...