Download Print this page

Toshiba SD-R1202 User Manual

Cd-rw/dvd-rom combo drive
Hide thumbs





  Also See for Toshiba SD-R1202

  Related Manuals for Toshiba SD-R1202

  Summary of Contents for Toshiba SD-R1202

  • Page 2: Table Of Contents

    CONTENTS Introduction................1 Setup ..................3 Using the Combo Drive ............6 Troubleshooting...............9 Specifications ................10 Drive Connectors..............13...
  • Page 3: Introduction

    INTRODUCTION – SD-R1202 General Features Reads and records digital data on CD-R/-RW discs at 16X/10X 3-way Disc Eject (eject button, software, emergency eject hole) Average Random Access Time 110ms DVD-ROM 130ms Horizontal or Vertical Mount 2MByte Buffer Playback interchangeability for CD-ROM and DVD-ROM discs...
  • Page 4 Front Panel Figure 1.SD-R1202 DVD Writeable Drive Front Panel Loading Load disc using tray. Tray The LED lights green or amber when the drive is operating (LED is amber when drive is Busy Light writing.) Eject The Eject button is used to open the disc tray so you can install or remove a disc.
  • Page 5: Setup

    SETUP – SD-R1202 The following steps must be performed to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pins located on the rear of the Combo drive.
  • Page 6 If the Combo drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in your system. Your Toshiba Combo drive can be placed in any free half-height drive slot at the front of your computer. (It can be mounted horizontally or vertically.) Carefully start sliding the Combo drive into the opening with the disc tray facing the front of the computer.
  • Page 7 DOS, download the DOS ATAPI driver from our web site. Other Software - Additional software is required to use the SD-R1202 CD-R/-RW and DVD functions. When you purchase the SD-R1202 as a kit, it will include the following software (Nero6): •...
  • Page 8: Using The Combo Drive

    USING THE DVD Combo Drive – SD-R1202 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is mounted horizontally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's Loading tray by pressing the Eject Button.
  • Page 9 3. Grasp disc by edges, and lift out of loading tray. 4. Press Eject Button again to close Loading Tray. Software When you purchase the SD-R1202 as a Kit, it will include Nero6 OEM Suite Software, which is used to create CDs and view DVDs. Usage Guidelines •...
  • Page 10 Emergency Ejection CAUTION: The following procedure is intended only as a last resort when pressing the eject button fails to open the Loading Tray 1. Turn computer power OFF by properly shutting down system. 2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push in until loading tray opens.
  • Page 11: Troubleshooting

    TROUBLESHOOTING – SD-R1202 Solution Problem • Disc tray cannot be opened Check that there is power to drive. • Use Emergency Eject instructions to open tray. • Drive is not recognized by system Is the drive connected properly? Are all cables plugged in properly (e.g.
  • Page 12: Specifications

    SPECIFICATIONS – SD-R1202 General Interface: ATAPI Applicable Formats - Write: Formats for Writing Disc at once, Track at once, session at once, Packet Write, incremental write, restricted overwrite Applicable Write Disc – CD-DA, CD+(E)G, CD-MIDI, CD-ROM, CD-ROM XA, CD-I, MIXED MODE...
  • Page 13 CD-R (Write) 3,400 – 5,940rpm (12/16X PCAV) 2,440 – 5,940rpm (12/16X ZCLV) 2,440 – 5,940rpm (12X CLV) 1,700 – 3,960rpm (8X CLV) 850 – 1,980prm (4X CLV) High Speed CD-RW (Write) 2,125 – 4,950rpm (10X CLV) 850 – 1,980rpm (4X CLV) CD-RW (Write) 850 –...
  • Page 14 Audio Connectors 4-pin and 2-pin connector (use matching housing, Part No. 70066, made by Molex Corp, or equivalent) Regulatory The SD-R1202 Combo drive has been certified by the following regulatory agencies: • UL 1950 • CSA C22.2 No. 950 •...
  • Page 15: Drive Connectors

    ON Audio Supplies Analog and Digital sound to your system. Connectors The SD-R1202 DVD drive is connected to your computer system through the ATAPI ATAPI connector Connector The mode select jumpers are 6 straight angle pins located on the rear of the DVD drive.
  • Page 16 Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT SIGNAL HOST SIGNAL NAME SIGNAL HOST SIGNAL NAME NAME NAME Reset Host Reset HDRQ DMA Request Host Data Bus BIT 7 HWR-,STOP Host I/O Write Host Data Bus BIT 8 Host Data Bus BIT 6 HRD-, Host I/O Read HDMARDY, -...