HP ProLiant DL360 Quickspecs page 33

QuickSpecs
Additional Options
HP Rack Series HP Rack Series HP Rack Series HP Rack Series
HP Modular Power Distribution Units (mPDU), High Volt Model, 16A (200-240 VAC)
(WW)
NOTE: This PDU has a detachable input power cord and allows for adaptability to NOTE: NOTE: NOTE:
country specific power requirements.
NOTE: Please see the following QuickSpecs for additional options including shorter NOTE: NOTE: NOTE:
jumper cables and country specific power cords:
http://h18000.www1.hp.com/products/quickspecs/11041_div/11041_div.html
(Worldwide)
NOTE: For additional information on HP Power Distribution Units including NOTE: NOTE: NOTE:
accessories please go to: www.hp.com/go/pdu.
NOTE: NOTE: NOTE: Please see the UPS and PDU cable matrix's on the HP Power Protection and NOTE:
Management page. Under Power Cords, click on the "HP Power Cord Matrix" link.
That link will list cable descriptions, requirements, and specifications for UPS and PDU
units. Please see the following link: www.hp.com/products/powercords.
HP Rack 10000 G2 Series (Carbon/Graphite Metallic) HP Rack 10000 G2 Series HP Rack 10000 G2 Series HP Rack 10000 G2 Series
HP 10642 G2 Pallet Universal Rack
HP 10642 G2 Shock Universal Rack
HP 10642 G2 1200mm deep Shock Rack
HP 10647 G2 1200mm deep Shock Rack
NOTE: It is mandatory to use a shock pallet when shipping racks with equipment NOTE: NOTE: NOTE:
installed.
NOTE: NOTE: NOTE: NOTE: Please see the QuickSpecs for additional information:
http://h18000.www1.hp.com/products/quickspecs/12402_div/12402_div.html
(Worldwide)
NOTE: For additional information regarding Rack Cabinets, please see the following NOTE: NOTE: NOTE:
URL: http://www.hp.com/go/rackandpower.
NOTE: NOTE: NOTE: NOTE: The increasing power of new high-performance processor technology requires
increased cooling efficiency for rack-mounted servers. The 10000 G2 Series Racks
provide enhanced airflow for maximum cooling, allowing these racks to be fully
loaded with servers using the latest processors.
CAUTION: If a third-party rack is used, observe the following additional requirements CAUTION: CAUTION: CAUTION:
to ensure adequate airflow and to prevent damage to the equipment: Front and rear
doors: If your 42U server rack includes closing front and rear doors, you must allow
830 square inches (5,350 sq cm) of hole evenly distributed from top to bottom to
permit adequate airflow (equivalent to the required 64 percent open area for
ventilation). Side: The clearance between the installed rack component and the side
panels of the rack must be a minimum of 2.75 inches (7 cm).
CAUTION: Always use blanking panels to fill all remaining empty front panel U- CAUTION: CAUTION: CAUTION:
spaces in the rack. This arrangement ensures proper airflow. Using a rack without
blanking panels results in improper cooling that can lead to thermal damage.
NOTE: NOTE: NOTE: For additional information, refer to the Setup and Installation Guide or the NOTE:
Documentation CD provided with the server, or to the server documentation located
in the Support section at the following URL: www.hp.com/servers/dl360.
Quick deploy rail system provides tool-free support for racks with square or round
mounting holes (including Compaq/HP 7000, 9000, 10000 G2 and HP series), with
an adjustment range of 24" - 36". The ambidextrous cable management arm can be
mounted on either the left or right side for improved cable management.
DA - 13235 Worldwide — Version 38 — October 14, 2011
HP ProLiant DL360 Generation 6 (G6) HP ProLiant DL360 Generation 6 (G6) HP ProLiant DL360 Generation 6 (G6) HP ProLiant DL360 Generation 6 (G6)
252663-B24
AF001A
AF002A
AF092A
AF094A
Page 33