Rotor Pedal Mode; Organ Trig Mode; Drawbar Speed; Midi Menu - Clavia Nord C2 User Manual

18 | NordC2ComboorgaNUsermaNUalosv1.X

Rotor Pedal Mode

If you are using a sustain pedal connected to control Rotor Speed
this allows you to set how this should operate . "Hold" means that the
Rotor Speed is fast for as long as the pedal is down and reverts back
to slow/stopped when the pedal is released (or vice versa depending
on the set pedal polarity) .
"Toggle" means that the fast & slow/stopped rotor speed is cycled
each time you activate the pedal, like an on/off switch pedal .
Range: Hd - Hold, (default), tO - Toggle.

Organ Trig Mode

This allows you to change how the Nord C2 keyboard triggers the
organ sounds . When "Fast" is selected, you will trigger organ sounds
before the key reaches the end of its travel . This mode closely mimics
the way a vintage tonewheel organ trigger its notes .
M The pipe organ model is not affected by this setting.
Range: F- Fast (default), n- normal

Drawbar Speed

This sets the speed with which the drawbars will increase or decrease
the values when the drawbar buttons are held down .
Range: F- Fast (default), S- slow .

MIDI Menu

Swell Channel

This sets the MIDI Channel that the swell manual on the Nord C2 trans-
mits and responds to .
Range: Off, 1-16 (default = 1)

Great Channel

This sets the MIDI channel that the great manual on the Nord C2 trans-
mits and responds to .
Range: Off, 1-16, (default = 2)

Pedal Channel

This sets the MIDI channel that the Bass section of the Nord C2 organ
transmits (if the Great manual is split) and responds to .
Range: Off, 1-16, (default = 3)

Local Control

This allows you to set if the Nord C2 keyboard and front panel controls
should control internal Programs or only send note and controller mes-
sages via MIDI . Local On is the normal "mode" . In Local Off mode, the
front panel and keyboard action are transmitted via MIDI only and does
not control the internal sound(s) directly .
If the "E" mode is active, the keyboard of the C2 will transmit velocity .
Range: On (default), Off, E - External Device
M Local defaults back to mode On every time the Nord C2 is pow-
ered on.

Control Change (CC) Mode

This setting specifies how the front panel's knobs and buttons are han-
dled in the MIDI communication with MIDI Control Change messages .
You can select if the panel controls and functions should either send or
receive, or both or if Control Change messages should be ignored .
Range: Sr (send & receive - default), r (receive only), S (send only),
Off

Program Change Mode

Specifies how the Nord C2 should handle MIDI Program Change mes-
sages .
Range: Sr (send & receive - default), r (receive only), S (send only),
Off
Send CC
You can perform a dump of all the active Program's parameters as
MIDI Control Change messages . Press the Store button to perform the
dump .

Dump One

This allows you to perform a MIDI SysEx dump of the currently selected
Program . Press the Store button to perform the dump .

Dump All

This allows you to perform a MIDI SysEx dump of all the Programs in
the Nord C2 . Press the Store button to perform the dump .
In the MIDI chapter, on page xx is a description on how the Nord C2
receives a Sys Ex dump .

Sound Menu

Treble Horn Speed

Sets the speed setting (in the fast and slow speed modes) of the rotary
speaker simulation's treble horn .
Range: H - High, n - Normal (default), L - Low

Bass Rotor Speed

Sets the speed setting (in the fast and slow speed modes) of the rotary
speaker simulation's bass rotor .
Range: H - High, n - Normal (default), L - Low

Treble Horn Acceleration

Sets the acceleration and retardation time of the rotary speaker simula-
tion's treble horn .
Range: H - High, n - Normal (default), L - Low